Smart Mini Sensor Instruction Manual

Product Description

This product is used to detect the opening and closing status of doors and windows. After the user installs it according to the instructions, the equipment enters the working state. When opening the door/window, pressing the button reports the door/window alarm data to the host computer. When closing the door/window, pressing the button also reports the door/window alarm data to the host computer. The host then pushes the alarm information to the user's mobile phone to achieve real-time alarm functionality.

When the product is powered on, it will detect the network status of the device. The LED light flashes 3 times.

Device Components

The Smart Mini Sensor consists of the following parts:

• 1. Main Magnet: The primary magnetic component.
• 2. Vice Magnet: The secondary magnetic component.
• 3. Network Access Hole: A small hole for network access operations.
• 4. LED Indication: An indicator light for status.
• 5. Opening Guide: A visual guide for alignment.
• 6. Sensing Area Side: The side of the sensor responsible for detection.

Visual Representation: The diagram shows three outlines. The first outline (labeled UIOT) depicts the main unit with labels pointing to the LED indication and sensing area. The second outline shows the main magnet and vice magnet side-by-side. The third outline shows the vice magnet. Labels 1 through 6 correspond to the components listed above.

Installation Instructions

Installation Requirements

• It is recommended to install the main magnet on the door (window) frame and the secondary magnet on the door (window) itself.
• The installation position should be firm. Avoid installing it outdoors.

Installation Steps

1. Open the lower cover of the main magnet, remove the battery separator, and power on the product.
2. According to the operating instructions, first perform the network access operation and then proceed to the next step of installation.
3. Choose to install door and window magnets on doors, windows, and other suitable scenes.
4. Peel off the 3M adhesive from the main magnet and the secondary magnet. Paste the devices to their selected positions. It must be ensured that the secondary magnet and the main magnet are next to each other when the door/window is closed, as shown in the figure below.

Visual Representation: Diagrams show typical installation on a door and a window. Another diagram illustrates the correct proximity of the main magnet and vice magnet when the door/window is closed, with a label indicating the maximum allowed distance is less than 15mm (<15mm).

Note: The installation distance between the main magnet and the secondary magnet should not be greater than the detection gap, so as not to affect the accuracy of door and window opening/closing detection.

APP Instructions

The UIOT smart home APP provides remote control capabilities.

1. Install UIOT Smart Home APP

Scan the QR code with your mobile phone to download the "UIOT smart home" APP, or search for "UIOT smart home" in your mobile app market to download and install.

2. Add Equipment

Premise: Ensure you have a UIOT intelligent server, powered on and connected to the network. Power on the device to be added.

1. Open and log into the UIOT "smart home" APP.
2. Navigate to "My" > "Equipment Management" > "+". Find and click "Smart Mini Sensor". Follow the APP prompts, inserting the card pin into the mesh hole for 3 seconds and releasing it.
3. After setting the device name and room, complete the addition.

3. APP Control

Through the "UIOT smart home" APP, you can:

• Check the current device alarm and fault status.
• Set the device state as a linkage trigger source to realize automatic control of the device.
• Pay attention to system control notifications; the APP of the system control device will receive alerts.
• Access help resources for further guidance.

4. Delete Device

If the device is connected to the network, long-press the shortlist button for 8 seconds to delete it.

Technical Specifications

• Product Color: White
• Product Material: PC
• Installation Method: Paste
• Product Size:
  • Main Magnet: 42.5*22.5*11.4mm
  • Vice Magnet: 30*10.5*9.5mm
• Power Supply: CR1632
• Communication: ZigBee
• Communication Distance: 50-80m (Open and unobstructed)
• Monitoring Method: Magnetic induction
• Detection Distance: ≤5m

Caution and Notice

Caution

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

• (1) This device may not cause harmful interference, and
• (2) This device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Notice

• There are fragile components in the product; please avoid destructive actions such as dropping or applying heavy pressure.
• The product contains precision electronic components; pay attention to waterproofing and avoid high temperatures during use.
• Do not let foreign objects fall into the machine.
• Do not disassemble or modify the machine in any way.
• The mains power supply must be cut off during the installation process to avoid accidents.
• Wiring must be done strictly in accordance with the product wiring diagram.
• Do not press the device hard during the wiring process to avoid damage.
• When fixing the bottom shell, do not press hard to avoid damage to the shell.
• Do not install the equipment in a humid environment.

Warranty

Warranty Policy Service Commitment

According to national "three guarantees" regulations, with valid bills and warranty certificates, enjoy the following services:

1. If the product has a performance failure within 7 days from the date of sale, the user can choose to return, exchange, or repair for free.
2. Within 15 days from the date of sale, if the product has a performance failure, the user can choose to exchange it or repair it for free. (After exchange, the three-guarantee period of the product itself will be recalculated.)
3. If the product has a performance failure within 1 year from the date of sale, the user can choose free maintenance service.
4. After the warranty period, if the product has a performance failure, the user can choose toll repair service.

Non-Warranty Regulations

Within the validity period of the three guarantees, in the following situations (not limited to these), the responsibility of the three guarantees will not be borne. However, reasonable maintenance fees should be provided.

• No valid bills and three-pack certificates.
• Unauthorized alteration of the three-guarantee certificate.
• The product name, model, and code on the invoice or three-guarantee certificate do not match the actual product.
• Failure to properly use, maintain, and store in accordance with the product instruction manual causes damage or failure.
• The user (not the party responsible for the three guarantees) causes damage or malfunctions due to improper disassembly.
• Damage or malfunction not caused by product quality problems.
• Machine failure beyond the warranty period.
• Damage or malfunction caused by force majeure.

Regulatory Compliance

FCC Radiation Exposure Statement

The transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. This equipment complies with the FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body.

Information to Users

According to FCC Part 15.19, 15.21, and 15.105 rules, for this EUT, the instructions or operation manual furnished to the user shall include the following or similar statement, placed in a prominent location in the text of the manual:

NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

IC WARNING (Canada)

This device contains licence-exempt transmitter(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions:

• (1) This device may not cause interference.
• (2) This device must accept any interference, including interference that may cause undesired operation of the device.

RF Exposure Statement (Canada)

This equipment meets the exemption from the routine evaluation limits in section 2.5 of RSS-102. It should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body.

Déclaration d'exposition aux radiofréquences (Canada)

Cet équipement est conforme à l'exemption des limites d'évaluation habituelle de la section 2.5 de la norme RSS-102. Il doit être installé et utilisé à une distance minimale de 20 cm entre le radiateur et toute partie de votre corps.