User Manual

Lock Body Overview

This section describes the components of the smart lock.

Exterior Lock:

The exterior part of the lock features:

• Light Indicator: Provides visual feedback.
• Keypad: For entering PIN codes.
• Fingerprint Reader: For biometric authentication.
• Key Hole: For mechanical key access.
• Type-C Backup Power Port: For emergency power supply.

Interior Lock:

The interior part of the lock features:

• Battery Cover: Houses the batteries.
• Thumb Turn: For manual locking and unlocking from the inside.

Specifications

Components Overview

The package includes the following components:

Installation Overview

This diagram illustrates the assembly process of the smart lock components onto a door. The exterior lock (a) attaches to the front rubber pad (b), which is mounted on the door. The mounting plate (c) secures the assembly. The deadbolt (e) passes through the door, and the interior lock (d) is attached to the mounting plate. Screws (i, j, k, l) are used for fastening various parts, and the battery cover is part of the interior lock assembly.

How to Install the Lock

Ensure your door meets the following requirements before installation:

• Door Thickness: 1-3/8" to 2"
• Hole Diameter (Cross-bore): 2-1/8"
• Backset Size: 2-3/8" or 2-3/4"

Deadbolt Adjustment: If the backset is 70mm, turn the faceplate 180° to extend its length.

Diagram showing door dimensions: 2-1/8" (Cross-bore diameter), 2-3/8" or 2-3/4" (Backset), 1-3/8" to 2" (Door thickness). Diagram showing deadbolt adjustment: a 2-3/8" (60mm) deadbolt can be extended to 2-3/4" (70mm) by rotating the faceplate 180°.

1. Fix the deadbolt (e) with 2 deadbolt/strike plate screws (i) and ensure it is retracted.
2. Attach the exterior lock (a) to the front rubber pad (b) and secure it onto the door.
3. Make sure the paddle is slid through the deadbolt and the cable is threaded through the door hole.
   NOTE: 1. Route the cable below the deadbolt. 2. Deadbolt must be in unlock position, and the paddle must be in 'horizontal' status.
4. Peel the tape off the mounting plate (j). Ensure the cable passes through the door and is positioned near the mounting plate. Then, fix the exterior lock with 2 interior lock screws (l); screw (i) can be fixed selectively.
5. Insert the cable into the wire connector and ensure it is properly and securely installed. Insert the paddle into the hole at the back of the thumb turn.
   NOTE: When pressing the indoor panel against the door, try to conceal the wires inside the door or place them in the designated wire-housing areas on the indoor panel.
6. Open the battery cover. Fix the back body (interior lock) to the mounting plate with 3 interior lock screws (k or l).
7. Place the batteries (?) in position and close the battery cover.
   NOTE: Insert AA batteries into the interior assembly while the door is locked.
8. Set the direction of the lock: This lock requires the deadbolt to be engaged to identify the open direction. Please make sure the deadbolt is engaged after installation.
   NOTE: If the deadbolt is retracted, a red light will flash, accompanied by a sound alarm to indicate that the lock's opening direction is not set. Please rotate the thumb turn to engage the deadbolt and set the opening direction.

How To Use

This section covers the basic operations and settings of the smart lock.

Alarms and Lockout

• Low Battery Alarm: 6 short beeps and red light flashing 6 times.
• Lockout for Incorrect PIN: After 3 unsuccessful PIN code entries, a light will flash accompanied by an alarm. The keypad will be locked for 180 seconds.

Reset Lock

Press the reset button (j) for 3 seconds. You will hear 1 long beep and see a blue light flash once, followed by 3 short beeps and a red light flash 3 times. After reset, the lock will revert to its factory default settings, with the Master PIN code set to 123456, and all User PIN codes and User fingerprints will be erased.

Change Master PIN code

The factory default Master PIN code is 123456. It is recommended to change this code upon receiving the lock.

Steps:

1. Enter 123456 + ⚙️
2. Press 4 + ⚙️
3. Enter New Master PIN code (6 digits) + ⚙️
4. Repeat Enter New Master PIN code (6 digits) + ⚙️

Add User PIN code

(Up to 98 user PIN codes can be set)

Steps:

1. Select "Add User PIN code".
2. Enter Master PIN code + ⚙️
3. Enter 1 + ⚙️
4. Enter ID number (02-99) + ⚙️
5. Enter User PIN code (4-9 digits) + ⚙️
6. Repeat Enter User PIN code (4-9 digits) + ⚙️

Adding User fingerprint

(Up to 50 new user fingerprints can be added)

Steps:

1. Select "Add User fingerprint".
2. Enter Master PIN code + ⚙️
3. Enter 1 + ⚙️
4. Enter ID number (01-50) + ⚙️
5. Press fingerprint reader 5 times.

Delete some of the User PIN codes

Steps:

1. Select "Delete some of the User PIN codes".
2. Enter Master PIN code + ⚙️
3. Enter 2 + ⚙️
4. Enter ID number (02-99) + ⚙️
5. Repeat Enter ID number + ⚙️

Delete some of the User fingerprints

Steps:

1. Select "Delete some of the User fingerprints".
2. Enter Master PIN code + ⚙️
3. Enter 2 + ⚙️
4. Enter ID number (01-50) + ⚙️
5. Repeat Enter ID number + ⚙️

Delete all User PIN codes at a time

(This action will delete user PIN codes but not the master PIN code)

Steps:

1. Select "Delete all User PIN codes at a time".
2. Enter Master PIN code + ⚙️
3. Enter 3 + ⚙️
4. Enter Master PIN code + ⚙️

Delete all User fingerprints at a time

(This action will delete all User fingerprints)

Steps:

1. Select "Delete all User fingerprints at a time".
2. Enter Master PIN code + ⚙️
3. Enter 3 + ⚙️
4. Enter Master PIN code + ⚙️

Delete all User PIN codes and all User fingerprints at the same time

(This action will delete all User PIN codes and User fingerprints but not the Master PIN code)

Steps:

1. Select "Delete all User at the same time".
2. Enter Master PIN code + ⚙️
3. Enter 3 + ⚙️
4. Enter Master PIN code + ⚙️

Auto lock mode

The lock will be locked automatically after a specified duration.

Steps:

1. Select "Auto lock mode".
2. Enter Master PIN code + ⚙️
3. Enter 5 + ⚙️
4. Enter duration (3-30 minutes) + ⚙️

Cancel Auto lock function

This programming will keep the door open all the time.

Steps:

1. Select "Cancel Auto lock function".
2. Enter Master PIN code + ⚙️
3. Enter 5 + ⚙️
4. Enter 00 + ⚙️

NOTE: You can press ? to lock the door.

Turn Sound on/off

You can "mute" or "unmute" your lock by entering the following commands (the feature is on by default).

Steps:

1. Select "Turn Sound on/off".
2. Enter Master PIN code + ⚙️
3. Enter 6 + ⚙️
4. Select "Sound OFF" or "Sound ON".

Alternative Steps:

1. Enter 1 + ⚙️
2. Enter 2 + ⚙️

Light and Sound Indication