Steel-Line Garage Doors Australia | Manufacturer & Supplier
User Guide for Steel-Line models including: SC100 Steel Roller Shutter, SC100, Steel Roller Shutter, Roller Shutter, Shutter
File Info : application/pdf, 2 Pages, 1.01MB
DocumentDocumentGuide with Silencing Strip Spring and Springless Option Standard Colours (available in 1.0mm) Surfmist® Shale GreyTM Ironstone® Monument® Duralloy Powdercoat Colours also available. 100mm Slat SC100 Steel Roller Shutter FEATURES · ROBUST · QUIETER OPERATION · EASILY INSTALLED AND MAINTAINED · CYCLONE RATED TO COMPLY WITH AS/NZS 1170.2-2011 · SHORT LEAD TIMES · MADE IN AUSTRALIA The SC100 Roll Formed Roller Shutter with 100mm Galvanized Steel slats as supplied by Steel-Line. The heavy duty steel slat is designed to withstand the wear and tear of industrial and commercial applications with minimal maintenance. The rolled slat can be replaced individually should the damage occur. The SC100 Steel Roller Shutter is purposely built with guide channel that has nylon rubber to minimize the noise that comes from the interlocking slats. The SC100 Steel Roller Shutter can be hand operated or electric operated. Each slat is fitted with nylon end clips to reduce the lateral movements and ensure smooth operation for the life of the door. The SC100 Steel Roller Shutter is available in a limited range of Colorbond colours. Standard Curtain The SC100 shutters are available in 0.8mm and 1mm thickness. Note: Recommended maximum width is 10 metres. Refer to Steel-Line Counterweight products for larger single span openings. Curtain Alternatives Slotted Slats (Ventilation) Any number of the slats can be punched with 90mm wide x 25mm high slots. Multi-hole Slats* The slats can also be continuously perforated with 2.41mm diameter holes at 3.66mm staggered centres prior to rolling (this allows maximum air flow the holes are over the entire surface area of the slat). These perforations cover 40% of the slat surface. *The perforation process removes much of the Galvabond protection from the slat. Premature surface corrosion may occur as a result. This is not covered by warranty. Roller Drum The roller drum is a robust seamless steel tube encasing the shaft and helical counterbalance spring (for manually operated). The end caps and roller bearings are designed to provide smooth operation. Guide Channels 2mm galvanized steel is roll formed with the nylon rubber to make a noticeably quiet steel roller shutter when opens and closes on a 100mm x 48mm guide channel. *Nylon rubber not available with wind locked guides. Support Bracket The support brackets are fabricated from mild steel plate and designed to be fitted to a solid fixing point of adequate strength to support the weight of the door and any wind loading that may be required (adequate fixing points to be supplied by others). Bottom Rail The bottom rail is roll formed from 3mm galvanized steel to make a 50mm x 50mm angle. This angle is securely fixed to the front of the slat (bottom of angle protrude to inside of opening). This can also be aluminium bottom rail. Operation Hand Operation Small roller shutters with an area of 6 square meters may be hand operated. Pull hook is provided for opening and closing the door. Electric Operated Motorization includes 1Hp motor incorporating a standard reversing contractor and an Up, Down, Stop button controller with a hand chain override in case of power failure. For remote control and other options, please contact Steel-Line. All wiring will be by others. Locking Operation Hand Operated will have sliding shoot bolts. Electric Operated by electrical motors and controls. Finish Standard finish is galvanised curtain and guides with all other exposed parts prime painted. Optional finishes to slats only is powder coating. For Cyclonic Conditions High strength wind locks and guides are designed to prevent the curtain from blowing out of the guide rail. Wind locks can be fitted every 2nd or every 4th slat depending on the location and function. 26 48 114 50 80 30 (TYP.) 68 Q100 BUNDLE DIAMETER & MINIMUM REQUIRED HEADROOM DRUM ø 165 165 165 165 165 HEIGHT 2000 3000 4000 5000 6000 WIDTH BUNDLE ø HEADROOM 5000 285 543 5000 345 573 5000 405 603 5000 465 633 5000 525 663 DRUM ø HEIGHT WIDTH BUNDLE ø HEADROOM 165 2000 6000 285 543 165 3000 6000 345 573 165 4000 6000 405 603 165 5000 6000 465 633 168 6000 6000 528 664 DRUM ø HEIGHT WIDTH BUNDLE ø HEADROOM 165 2000 7000 285 543 168 3000 7000 348 574 168 4000 7000 408 604 168 5000 7000 468 634 168 6000 7000 528 664 DRUM ø HEIGHT WIDTH BUNDLE ø HEADROOM 168 2000 8000 288 544 219 3000 8000 399 600 219 4000 8000 459 630 219 5000 8000 519 660 219 6000 8000 579 690 165 7000 5000 585 693 168 7000 6000 588 694 219 7000 7000 639 720 N/A 7000 8000 N/A N/A 165 8000 5000 645 723 168 8000 6000 648 724 219 8000 7000 699 750 N/A 8000 8000 N/A N/A 100 100 25 103 20x10 FL Silencer strip STANDARD 100mm GUIDE CHANNEL 48 3 25 STANDARD WIND LOCK GUIDE 100mm SLAT 168 9000 5000 708 754 168 9000 6000 708 754 N/A 9000 7000 N/A N/A N/A 9000 8000 N/A N/A 64 ALUMINIUM BOTTOM RAIL (Up to 5800mm Only) STANDARD 1.0mm SLAT 1.0MM SLAT CUT TO SUIT 1.0MM SLAT 75x50x2.5 RHS 50 STEEL ANGLE BOTTOM RAIL STEEL REVIT STEEL BOX EVERY 500MM BOTTOM RAIL MULTI-HOLE SLAT 40% ventilation per slat STANDARD SLOTTED SLAT (Ventilation) NYLONE END CLIP BOTTOM RAIL 50x50x3 Galv. Angle Steel-Line reserves the right to change specifications at any time without notice. V3 (0521) Copyright © Steel-Line Garage Door Australia. All rights reserved. QBBC: 1129059 | CBS: 223285 Call 1300 427 243 | steel-line.com.au