3633coolon.com
Instruction Manual for COOLON models including: MBR-RB-TB-BLK ARIS Compact Medium Power LED Linear Floodlight, MBR-RB-TB-BLK, ARIS Compact Medium Power LED Linear Floodlight, Compact Medium Power LED Linear Floodlight, Medium Power LED Linear Floodlight, Power LED Linear Floodlight, LED Linear Floodlight, Linear Floodlight, Floodlight
File Info : application/pdf, 4 Pages, 756.61KB
DocumentDocumentARIS INSTALL ATION INSTRUCTIONS PROFILE DIMENSIONS 25mm 25mm 4.5mm Approximately 14mm With MC-CCLIP Stainless Steel C-Clip A 11.4mm 26.5mm Minimum 12mm screw 25mm 6.8mm B C 5mm 20mm With MBR-RB-TA-BLK & MBR-RB-TB-BLK Rotating Bracket Type A & Type B TYPE A 25mm 35° TYPE B 125° 25mm ARIS INSTALLATION INSTRUCTIONS ATTENTION · Please observe / follow the instructions methodically. · Please ensure the units are handled with extreme care. · Do not remove LED strips from packaging prematurely. Only remove from packaging when ready for installation. · Failure to observe installation instructions and handling will void warranty of the product. ØBmm Cmm MC-CCLIP M B R- R B -TA / TB - M A X ØAmm A (Ø_mm) Screw outer diameter 3.5 4 B (Ø_mm) Screw head clearance 6.6 N/A C (mm) Screw head pocket depth 2.5 N/A 115° A 75° 2.5mm 60mm minimum clearance required for full rotation 60mm minimum clearance required for full rotation 46mm 46mm 22mm Minimum 12mm screw Minimum 12mm screw 27.5mm 90mm minimum clearance required for full rotation 45mm archsales@coolon.com.au aus. 1300 287 533 intl. +613 8681 3633 w w w.c o o l o n.c o m.a u All documentation is subject to change without notice. Refer to our website for the latest information. 90mm minimum clearance required for full rotation 29.4mm 39mm Version 1.1 ARIS INSTALLATION INSTRUCTIONS STEP 1 Before you begin installation, ensure that you understand the fitting layout required as supplied fitting lengths may vary. Refer to the supplied cut sheet for length breakdowns. * For fittings 1 metre or longer two installers are recommended. Product Length STAINLESS STEEL C-CLIP STEP 3 Prepare mounting clips and screws (Ø3mm with a minimum length of 12mm). Secure mounting clips with screws on timber or metal surface ensuring that mounting clips are straight with spacings of 500 600mm. 12mm length minimum Ø3mm ROTATING BRACKET TYPE A & TYPE B STEP 2 Place rhomb nut in the base of the extrusion of the luminaire, ensuring that the edges of the nut are parallel with the edges of the extrusion. Next place the plastic aligning clip over the rhomb nut. Stainless Steel C-Clip 500 600mm WIRING If the fitting is wired from the back: It will need to wired before mounting. If the fitting is wired from the side: It will need to wired after mounting. Wire the fitting to the correct power supply as advised on the cut sheet. STEP 4 Lay the LED fitting on top of the clips and align so all clips are centred. Starting at one end push down the fitting until you hear the clip lock into place. Continue along the profile until all clips are locked. STEP 3 Place the edge of the bracket (with the slight lip) over the extrusion and secure the bracket to the rhomb nut using the screw provided. archsales@coolon.com.au aus. 1300 287 533 intl. +613 8681 3633 w w w.c o o l o n.c o m.a u All documentation is subject to change without notice. Refer to our website for the latest information. Version 1.1 STEP 4 Prepare screws (Ø4mm). Secure the other side of the bracket with screws on timber or metal surface ensuring that mounting clips are straight with spacings of 1,000mm. STEP 6 Wire the fitting to the correct power supply as advised on the cut sheet. * Typically supplied with AU flex and plug (1.8m long) Approximately 1,000mm spacings STEP 5 Rotate the fitting to the desired angle and use Allen key provided to tighten bracket to secure in place. TYPE A 35° 125° Lock when at desired angle TYPE B 115° 75° Lock when at desired angle to Mains AC/L (Brown) AC/N (Blue) FG (Green/Yellow) to Luminaire V (Black) +V(Red) archsales@coolon.com.au aus. 1300 287 533 intl. +613 8681 3633 w w w.c o o l o n.c o m.a u All documentation is subject to change without notice. Refer to our website for the latest information. ARIS INSTALLATION INSTRUCTIONS Version 1.1