New Item Warranty | Moultrie Warranty Policy | Learn More
Instruction Manual for MOULTRIE models including: MFG-15047, 053695150475, Ranch Series, Ranch Series 300lb Hopper Broadcast Feeder, 300lb Hopper Broadcast Feeder, Hopper Broadcast Feeder, Broadcast Feeder, Feeder
300-lb Gray Steel Deer Feeder 053695150475
24 ore fa — Thank you for your purchase of a Moultrie Ranch Series 300lb Hopper. Please read this sheet before operating the unit. If you should have any questions ...
5 days ago —
File Info : application/pdf, 5 Pages, 4.97MB
DocumentDocumentInstructions for Ranch Series 300lb Hopper Thank you for your purchase of a Moultrie Ranch Series 300lb Hopper. Please read this sheet before operating the unit. If you should have any questions about this product or any other Moultrie product, please contact us using the information on the back of this sheet. Allow us to better serve you by activating your 1-year warranty online at http://www.moultriefeeders.com/warranty . Short M6 Bolt M6 x 1 x 14 Qty. 16 M6 Lock Nut M6 x 1 Qty. 16 Short M8 Bolt M8 x 1.25 x 14 Qty. 8 A ASSEMBLE THE HOPPER Remove all hardware from packaging. M8 Lock Nut M8 x 1.25 Qty. 16 Long M8 Bolt M8 x 1.25 x 50 Qty. 8 Top Gather all 4 hopper panels and the hopper cone. Place the cone on its side, with the front arrow pointing either Left or Right. Attach both face panels to the cone using (4) M6 Short Bolts and (4) M6 Lock Nut. Hand tighten only. Face Panel (x2) Face Panels Side Panel (x2) Bottom Cone (x1) (x4) Cone Place a face panel on top of the cone and overlapping the side panels. Align the bolt holes in the cone with the (2) lower holes in the face panel. Secure using (2) Short M6 Bolts and (2) M6 Lock Nuts. Hand tighten only. Side Panel Face Panel M6 M6 Lock Nut Short Bolt M6 Short Bolt (x4) M6 Lock Nut Flip the hopper over and install the remaining face panel following the same procedure above. OPTIONAL: (2) Solar Panel Mounts are included with the kit. Install during this step if you choose to use them. (Not included with Gravity Kit) Stand the hopper upright with the cone flat on the floor. Align the bolt holes in the top (4) corners. Secure with (4) Short M6 Bolts and (4) M6 Lock Nuts. Hand tighten only. M6 Lock Nut M6 Short Bolt M6 Lock Nut Solar Panel Mount M6 Short Bolt Place the (4) leg brackets against the corner bracket mounting holes as shown, align the holes and insert (2) short M8 bolts from the outside of each leg bracket into the hopper. Secure with a hand-tight M8 lock nut on each bolt (8). Bracket Mounting Hole M8 Lock Nut Short M8 Bolt Leg Bracket Leg Bracket Leg Bracket (x4) Go back and tighten all previously installed bolts. M6 bolts will require a 10mm wrench, M8 bolts (leg bracket) will require a 13mm wrench. Note: Do not overtighten. Install the Face Panel Tabs (2) to both the face panels, using a short M6 bolt and a lock nut. Tighten with a 10mm wrench. The "lip" should point upwards to create a hanger for the lid handle while filling feeder. Lip Face Panel Tab (x2) Face Panel Tab M6 Lock Nut M6 Bolt Face Panel (x2) B ASSEMBLE & INSTALL THE LEGS Collect all 4 Top-Leg sections. Insert each section into a leg bracket. Set the leg angle to either 0° or 15° (15º recommended for most installations). Secure each with (2) long M8 bolts and (2) M8 lock nuts. Tighten using a 13mm wrench. Top Leg (x4) Long M8 Bolt M8 Lock Nut Top Leg (x4) Leg Bracket 15 Degree Leg Orientation 0 Degrees 15 Degrees (recommended) Insert the remaining leg sections into the (4) top-leg sections. Tap firmly on the end of the legs when joining leg sections; this will help to keep them locked together. Top Leg Leg Section Leg Sections (x4) C INSTALL FEEDER KIT ONTO HOPPER See additional feeder kit instructions for installation. D INSTALL INTERNAL FUNNEL After installing your feeder kit onto your hopper, insert the internal funnel into the hopper, letting the self-alignment ring lock it into place at the bottom of the hopper cone. NOTE: Make sure internal funnel is fully seated at hopper exit, and placed at the very bottom of the hopper. Funnel alignment is critical to proper feeder operation. Internal Funnel Internal Funnel Self-Alignment Ring E ASSEMBLE & INSTALL THE LID Install the Lid Tabs (2) to the mounting holes on the lid by inserting a short M6 bolt from the INSIDE of the lid and securing with a lock nut tightened with a 10mm wrench. These will enable you to lock your feeder lid using most standard locks. Lid Lock Nut Lid Tab (x2) Place the lid assembly on top of the feeder with the tabs aligned. The handles should be on the sides of the feeder. Lid Assembly Lid Tab Handle Panel Tab Our Service Department will gladly answer any questions you have. www.moultriefeeders.com/support 11292022 / MFG-15042 · MFG-15045 · MFG-15047 (x2) Lid Tab M6 Bolt Instructions for Ranch Series Gravity Feeder Kit Thank you for your purchase of a Moultrie Ranch Series Gravity Feeder Kit. Please read this sheet before operating the unit. If you should have any questions about this product or any other Moultrie product, please contact us using the information on the back of this sheet. Allow us to better serve you by activating your 1-year warranty online at http://www.moultriefeeders.com/warranty . Hex Bolt M6 x 1 x 18 Qty. 9 Flat Washer M6 Qty. 6* * 3 only required if mounting to a hopper other than Moultrie Ranch Series A ASSEMBLE FEEDER KIT Hex Nut M6 x 1 Qty. 9** ** 3 only required if mounting to a hopper other than Moultrie Ranch Series Remove all hardware from packaging. Fit the Extension Tube to the top of the gravity head, aligning the 3 bolt holes. NOTE: Extension Tube can be left off if a higher feeding elevation is desired. Extension Tube Bolt Holes Gravity Head From the outside of the extension tube, Insert the (3) M6 bolts through the holes from Step 3. Secure with the supplied hex nuts on the inside of the tube. Once all three bolts are in place and hex nuts are finger tight, fully tighten with 10mm wrench. ONLY TIGHTEN AFTER ALL 3 BOLTS ARE INSTALLED (10mm wrench) M6 Nut M6 Bolt Following the same procedure from Step 3, attach the Mounting Plate (ribs facing downward) to the top of the Extension Tube. ONLY TIGHTEN AFTER ALL 3 BOLTS ARE INSTALLED (10mm wrench) Mounting Plate The kit is now ready to be installed to your hopper. Rotate the kit so that the 4 feed chutes are all spaced evenly between the feeder legs. Align the (3) pre-installed mounting nuts in the bottom of the hopper with the (3) holes in the mounting plate, then secure the kit using (3) Hex Bolts and (3) Flat Washers. ONLY TIGHTEN AFTER ALL 3 BOLTS ARE INSTALLED (10mm wrench) Align hardware with mounting plate holes and lift kit to hopper Insert a bolt and washer into each threaded nut Tighten all mounting hardware Our Service Department will gladly answer any questions you have. www.moultriefeeders.com/support 0615023 / MFA-15047 · MFG-15050