User Manual for ATETOOL models including: AE988, AE988D, AE970, AE970D, Soldering Station
ATETOOL AE970D: Soldering station, AE970D, 1-channel, 80 W at reichelt elektronik
ATETOOL AE970D: Lötstation, AE970D, 1-Kanal, 80 W bei reichelt elektronik
User Manual
AE988/AE988D/AE970/AE970D Soldering Station
Packing List
Main unit: 1pc
Handle:
1pc
Iron stand 1pc
User manual: 1pc
Brass wool: 1pc
Main unit AE988/AE970) Main unit AE988D/AE970D)
AE988/AE988D/AE970/AE970D
Handle Product Specification
Iron stand
Brass wool
User manual
Model No.
AE988
AE970
AE988D
AE970D
Total Power
70W
80W Main Unit
70W
80W
Output voltage
25VAC
Temperature range
Temperature stability Dimension
200480(392-896)
50500 (122-932)
±1±1.8{200(400)}
148x120x85mm
150550 (302-1022)
weightcpower cable excluded
1.32kg
1.32kg
1.33kg
1.334kg
Handle
Power consumption Tip to ground impedance
Tip to ground voltage
65W
75W
65W
<2 <2mV
75W
Heating element
PTC ceramic heater
Integrated tip
PTC ceramic heater
Integrated tip
Cable length
1.2m
Weight
79g
68g
79g
68g
Note: specifications and appearance are subject to change for product improvement without prior notice
1
Safety and Precautions
The precautions in this manual are divided into the following [warning] and [attention]. Please fully understand the content.
!
Warning: misuse may cause death or serious injury to the user
!
Note: misuse may cause injury to users or substantial damage to objects involved
For your own safety, please strictly abide by the following precautions
Warning
When power is on, the temperature of the soldering iron tip might reach to
!
50 ~ 550 (120 ~ 1022).
Misuse may cause burns and fire, please strictly observe the following precautions:
Do not touch the soldering iron tip or the metal part around it while using Do not use it around combustibles Inform the people around of the potential risk caused by high temperature Turn the power off when not in use Before replacing parts or tip, turn off the power and wait till the iron tip cools down Do not use this product if you are inexperienced or have no sufficient necessary knowledge
without the guidance of related qualified personnel Please keep it out of reach of children If the power cord is damaged, please ask the manufacturer or its service agent or similar qualified
personnel to repair it, so as to avoid personal injury or damage to product
Please strictly observe the following precautions, otherwise it may cause injuries or death Do not use this product for works other than soldering Do not hit the handle hard for removing the tin on the iron tip Do not modify this product When replace parts, must use original ATETOOL parts Do not soak the product in water or use it with wet hands Unplug it properly after using Smoke will be emitted during soldering, please use it in open space Do not engage in other dangerous acts with this product
Using Method(AE988D/AE970D)
1.Operation and display instructions
Indicator Socket
LED segment Function key
Knob Calibration hole
Panel display:
LED segment: digital display
Indicator:
indicates the statement of heater (light on/off means power on/off)
Function key: function operation
Knob:
to adjust temperature
Calibration hole: for calibrate the temperature
2
2.Turn on the power switch
After switching on, indicator lights up and LED segment displays
for 1 second, now power is on.
And then it displays the temperature unit
or
for 1 second, so you know which unit is used
right now. If the standby function is enabled in this soldering station,
will be displayed for 1 second
to show standby function is available. Then displays the set temperature for 1.5 seconds, and finally displays
the real time temperature. When the temperature is stable, indicator will flash.
Note: when not in use, please put the soldering iron on the holder. If it won't be used for a while, please cut off
the power supply.
3.After use
After use, please clean the soldering iron tip and apply new solder on it.
4.Temperature unit conversion
First press function key, in the meanwhile switch on the power, till LED segment displays
, release
the function key, now the temperature unit changes. If it was Fahrenheit, now switch to Celsius, and vice versa.
5.Temperature adjustment
Temperature range AE988D50-500¥c122-932 AE970D150-550¥c302-1022, note: as LED segment shows only 3 digits, 1022 will be displayed as A22, "A" represents digit "10" Temperature adjusted by knob.
6.Screen brightness setting
1) Press and hold the function key till the the screen displays
, to enter the brightness setting.
2) Show the current digital display brightness level
-
.
3) Adjust the brightness level through the knob: gear 1-6.
4) Press the function key or wait for 10s to automatically save to complete the setting.
7.Standby and sleep functions
Standby function on and off:
1)Press and hold the function key till
display on LED segment to enter the standby function on/off setting:
2)Display the current setting
or
3)Adjust by knob:
or
to turn on/off the standby and sleep function.
4)Press the function key or wait for 10s to automatically save to complete the setting.
Standby function
1)When standby function is turned on, the soldering station will enter standby mode after not in use for 10 minutes.
2)In standby mode, LED segment displays
and temperature drops to 250 (482 ).
3)When any operation is detected, such as using the soldering iron, adjusting knob or pressing the function key,
it will return to the work mode.
4)When in standby mode, if no further operation is detected for 10 minutes, it will enter sleep mode.
Sleep function:
1)That short press the function key or long time in standby mode can make it enter sleep mode:
2)When entering sleep mode, screen displays
and heating is turn off.
3)Press the function key to return to normal heating work mode.
8.Temperature locking function:
Temperature locking function on and off:
1)Turning the knob to adjust the temperature to be set.
2)Long press the function key till
is displayed.
3)Now LEd segment displays
or
4)Turn the knob to set the locking function to be
or
5)Press the function key or wait for 10s to automatically save to complete the setting.
6)When the temperature is locked, adjusting the knob does not change the setting temperature, it will display
for 1 second to show that the current temperature is locked.
3
9.Temperature calibration
1) Adjust the set temperature to 350 ¥ (662 ) by knob and wait for 2 minutes to stabilize the temperature. 2) Use a thermometer to measure the temperature of the soldering iron tip. 3) Use a cross screwdriver to adjust the calibration hole to make the displayed temperature value equal to the measured value. For example, if the measured value is 345 ¥, adjust calibration hole to reduce display temperature 350 to 345, make the display temperature match the measured value. 4) Press the function key to complete calibration.
Using MethodcAE988/AE970
1.Operation and display instructions
Indicator socket
Knob Calibration hole
Indicator:
indicate the power state(light on/off means power on/off)
Knob:
adjust the temperature
Calibration hole: for calibrate the temperature
2.Switch on the power
After the power is on, indicator lights up, and the soldering station starts heating up according to the set temperature. After the temperature is stable, indicator flashes. Note: when not in use, please put the soldering iron on the holder. If it won't used for a while, please cut off the power supply.
3.Temperature adjustment
Temperature range: AE988/AE970200-480¥c392-896 Temperature adjusted by knob.
4.Temperature calibration
1) Adjust the set temperature to 350 ¥ (662 ) by knob and wait for 2 minutes to stabilize the temperature. 2) Use a thermometer to measure the temperature of the soldering iron tip. 3) Use a cross screwdriver to adjust calibration hole to make the measured value equal to set temperaure. For example, if measured value is 345¥
adjust calibration hole to increase it to 350, make the measured value match set temperature. 4) Temperature calibration completed.
Maintenance
In order to make this product durable, please maintain it regularly. The lifespan of this product depends on the used temperature, quality of solder wire and soldering paste, frequency of use etc. Please repair and maintain it according to specific use conditions.
! Warning
Please pay close attention when the soldering station is in use at high temperature, cut off the power and unplug the power cord after use.
4
Soldering iron tip maintenance 1. Set the temperature to 250 ¥ (480 ). 2. After the temperature is stable, clean the soldering iron tip with a brass wool and check its condition. 3. If black oxide is attached to it, please apply new solder (including flux) and wipe it repeatedly with a brass wool until it's clean, then apply some new solder. 4. If the soldering iron tip has been deformed, perforated or worn out, please replace it with a new one.
T900M series soldering tipsAE988/AE988D)
900M-T-I
900M-T-B
900M-T-K
Troubleshooting Guide
! Warning
When checking or replacing parts, be sure to pull out the power plug to prevent electric shock If the power cable is damage, it must be sent to the manufacturer, agency store or maintenance personnel with the same qualification for repair to avoid accidents
Failure phenomenon
Examination
Check whether the power cord is good, or plug falls off
Dealing method
Connect the power supply well
Not working after power is on
The display shows "S-E"
Is the fuse OK
Whether the handle cable is well connected with main unit Whether the wire connecting to handle is broken
Whether the heater is damaged (the resistance of the blue lead wire shall be less than 100 at room temperature).
Figure out the cause of fuse damage: 1. Short circuit inside the station. 2. Inside the handle, the spring might meets the heating element. 3. Check whether the pin of heating element is twisted or short circuited. Even if the cause is unknown, please replace the fuse. If the fuse get burnt out again, please return the handle with the main unit for maintenance.
Reconnected
If so please replace it with a new handle
If damaged, replace the heater
The display shows "H-E"
Whether the wire connecting to handle is broken
Whether the heater is damaged (the resistance of the red lead wire shall be less than 100 at room temperature)
If so please replace it with a new handle If damaged, replace the heater
Iron tip heating is on and off
The solder won't get on the iron tip
Whether the wire connecting to handle is broken
Check whether the temperature of the iron tip is too high
Check whether there is oxide on the tip
If so please replace it with a new handle Adjust to the proper temperature Clean the oxide with a brass wool
Iron tip temperature is too low
Check whether there is oxide on the tip
Clean the oxide with a brass wool
Whether the temperature is proper Adjust to the proper temperature
The iron tip won't fit
Whether there is oxide inside tip, or Change the tip and heater soldering iron tip expands
Not original tip or not same type tip use original factory tip or same type tips
The actual temperature can't reach
Is the temperature adjusted correctly
Haven't done temperature calibration for a long time
Adjust the set temperature again Re-calibrate temperature accordingly
5
900M-T-1.2D
900M-T-1.6D
900M-T-3.2D
900M-T-4.6D
900M-T-0.8C
900M-T-3C
900M-T-6.4C (More soldering tips information please contact us)
T80 series soldering tipsAE970/AE970D)
900M-T-2.4D 900M-T-6.5D 900M-T-5C
T80-B2
R0.5 10
T80-B2
R0.2 12
T80-BL
R0.2 9.5
T80-I
R0.15 13.5
T80-ILS
R0.2 7.5
T80-B
4.7
2
45°
15
T80-K
3 1.2
45° 11
T80-KU
4.7
2.4
45°
17 T80-KF
4.7
1.5
45°
11
T80-KL
3.5 R0.2
12 T80-J02
1 11.5
T80-BC1 2
11.5 T80-BC2
3
10 T80-BC3
(More soldering tips information please contact us)
Shenzhen ATETOOL Co., Ltd.
AddressF5, 1-2 #, Tongfuyu, Aiqun Road, Shiyan Street, Bao'an District, Shenzhen, 518132,P.R.China
Tel (0755) 23408674 - 802 Support(0755) 23408704 - 818 URL www.atten.com.cn( in Chinese )
www.atten.com(in English)
6
0.8 0.5
9.5 T80-D08 1.2 0.5
10 T80-D12 1.6 0.5
10 T80-D16 2.4 0.5
10 T80-D24
MADE IN CHINA CBN300123cA)
Adobe PDF library 15.00 Adobe Illustrator(R) 17.0