ILIFE V80 Max Robotic Vacuum Cleaner

Dear Customer

Thank you for purchasing the ILIFE V80 Max robotic vacuum cleaner! You've joined millions of people who clean with robots – the smarter way to get it done.

Please take a few moments to read this manual and get acquainted with your robot to ensure the best performance. If you encounter any problems, do not hesitate to contact customer service or visit our website at www.iliferobot.com for more information.

Stay connected with ILIFE on Facebook and Twitter for exclusive benefits:

• Get support tailored to your specific robot, including answers to questions, maintenance tips, video demos, and live chat.
• Be among the first to receive product updates, valuable information about new robots, exclusive discounts, and special promotions.

Connect with us:

• Facebook: facebook.com/iliferobotics
• Twitter: twitter.com/ILIFEROBOTUS

Enjoy a thorough cleaning every day!

Best regards,
ILIFE Innovation

ILIFE Customer Service

Russia
? 89299401228 (Mon-Fri: 9:00 - 18:00)
? service_russia@iliferobot.com

Other countries
? support@iliferobot.com

For more detailed information, please visit: www.iliferobot.com

Important Tips

⚠️ WARNING: V80 Max contains electronic parts. Do not submerge the robot or spray it with water. Clean with a dry cloth only.

For best usage

• Place the charging dock against the wall in a wide open area. Do not place the charging dock near a door or stairs.
• Remove excess clutter from the floor before cleaning (e.g., electrical cords, cables, small objects, etc.).
• Choose MAX mode to clean an area with highly concentrated dirt and dust.

Maintenance

• Clean the side brush and suction inlet when they become dirty and replace them if they become damaged. (See figure 1)
• Remove the nose wheel and holder by pulling the wheel straight up. Clean the debris and hair from the wheel cavity as well as the axle that holds the wheel in place. This should be done once a month. (See figure 2)
• Empty the dustbin and clean the filter after each use. Replace the filter every month.

Safety Instructions

Before using this product, please read the following safety instructions and follow all normal safety precautions.

• Read this user manual thoroughly and carefully before using this product.
• Keep this user manual.
• Any operation or use of this product in any way other than that described in this manual may lead to serious injury or product damage.

WARNING

1. Only certified technicians may disassemble the product. Users are not allowed to disassemble or repair the product.
2. Only use the AC adapter provided by the factory. Using other AC adapters may cause electric shock, fire, or product damage.
3. Do not touch the power cord, plug, or adapter when your hands are wet.
4. Keep loose clothing and fingers away from being drawn into the product's wheels.
5. Keep the robot vacuum away from all flammables.
6. Never clean the robot while it is on the charging dock or plugged in directly. Unplug the robot and turn off the power switch when cleaning.
7. Keep the AC power cord tucked away from becoming damaged in any way.
8. This product is to be used only indoors. Not intended for outdoor use.
9. Do not sit on top of the product or attach an object on the top of it.
10. Do not use this product in wet or moist environments.
11. Before use, remove all objects that could get caught in the brushes or suction passage.
12. Do not place this product on furniture or platforms where it can fall and be damaged.
13. To avoid battery damage, please check whether the adapter and outlet are properly connected.
14. To avoid any tripping hazards or injuries, please inform all people in the house when this product is in use.
15. Do not use this product when the dustbin is full.
16. Normal operating temperatures: -10 to 50 (centigrade).
17. Do not operate this product in high-temperature environments.
18. The battery must be removed from the product before it is scrapped.
19. Unplug the vacuum from the power source when removing the battery.
20. The battery is to be disposed of safely.
21. Use factory-authorized battery only. Do not use unmatched batteries.

NOTE: This product is not a toy and should not be used by children or people with a lack of related experience or knowledge.

Product Composition

List of accessories

Robot anatomy

Top View:

• Bumper
• Clean / Pause button
• Dustbin release button
• WiFi indicator

Bottom View:

• Cliff sensors
• Nose wheel
• Side brushes
• Charging pins
• Battery lid
• Side wheels
• Dustbin

Side View:

• Dustbin
• Power switch
• DC-in

Dustbin

Components: High performance filter, Sponge, Primary filter, Dustbin cover, Dustbin.

Water tank

Components: Water inlet, Water tank, Mop bracket, Mopping cloth.

Charging dock

Components: Power supply socket, Signal light, Power adapter, Charging pins.

CLEAN button status

Remote control operating

The remote control has the following functions:

• 1. Starting up/Pause: Press the button to switch the robot from Sleep Mode to Select Mode. Press the button when in Select Mode to start cleaning. Press the button to Pause the robot during its operation.
• 2. Clock: Press this button to enter clock mode when in selected mode or charging mode. Press this button to confirm clock setting in clock mode.
• 3. Spot mode button: Press the button to start the spot cleaning in selected mode.
• 4. Auto charge button: Press the button and the robot will return to the charging dock for recharging.
• 5. Display screen: Shows the current time and schedule.
• 6. Directional buttons:
• Forward: Press the button to move the robot forward in selected mode.
• Left: Press the button and the robot will turn left in selected mode.
• Right: Press the button and the robot will turn right in selected mode.
• 7. Plan: Press this button to enter scheduling mode when in selected mode or charging mode. Press this button to confirm scheduling in scheduling mode.
• 8. MAX mode: Under the Cleaning Mode, to clean dust traffic areas, press the MAX button to increase the suction level, and the vacuum will go to deep cleaning mode.
• 9. Edge mode/Classic mode button: Edge mode: press the button once to enter edge cleaning when the robot is in selected mode. Classic mode: press the button twice to enter classic cleaning when the robot is in selected mode.

Note: Install two AAA type batteries into the remote control. Take out the batteries if the remote control is not used for a long time.

Product specifications

Remark: The company reserves the right of final decision on the interpretation of these terms and conditions.

Product Operation

Charging dock

1. Placement of charging dock:
   • Connect the adapter with the charging dock.
   • Placement of the charging dock: place the charging dock against the wall horizontally. Ensure there is no object on the left and right side within one meter, and in the front within two meters. There should also be no reflective objects, such as mirrors, around the dock.
   • Connect the power.

   Reminder: When the charging dock is connected to the adapter, the signal light of the dock will light up.

2. Turn on the robot:
   • Turn on the power button on the side. Use "I" for ON, "O" for OFF.

   Reminder: After the robot finishes its work, please do not turn it off; keep it recharged for the next run.

3. Robot charging:
   • A. Auto charging: Under the Auto mode, the robot will automatically search for the charging dock when the power is low. Under the selected mode, the robot will begin to search for the charging dock when the respective button on the remote control is pressed.

   Reminder: Please keep the charging pins clean in daily use to ensure a good connection.

   • B. Manual charging: Turn on the power button on the side of the robot, connect the adapter with the robot, and then plug the adapter into the power socket.

   Reminder:

   • Charge for 6 hours for the first time.
   • Please leave the robot on the charging dock in daily use and make sure that the charging dock is connected to the power and the main switch is on.
   • If you won't use the robot for a long time, please fully charge it, turn off the power, and store it in a well-ventilated dry place.
   • Please do not use manual recharge mode under the Schedule Mode, otherwise the robot cannot perform the function of Schedule Mode.

Start/Pause/Sleep

Sleeping mode: Robot is not working, light at the '►II' button is off, and power switch is on.

Selected mode: Robot is not working, green light at the '►II' button flashes.

Cleaning mode: Robot is working, green light at the '►II' button turns solid.

1. Starting up:
   • Make sure that the power switch on the side of the robot is "ON".
   • Press the '►II' button to start operation.
   • Press the '►II' button on the remote control to start operation.

   Reminder: If the robot is in Sleep Mode, press the '►II' button to wake up the robot and enter Select Mode, then press the '►II' button once again, and the robot will automatically start operation.

2. Pause:

   'Pause' will switch the robot from Cleaning Mode to Select Mode, and it can be enabled by pressing the '►II' button on the remote control or the '►II' button on the robot.

   Reminder: You can operate the machine again after it's paused.

3. Sleep:
   • To enter the Sleep Mode: Press the '►II' button for three seconds.
   • The machine will automatically enter the Sleep Mode if no action is taken for 10 minutes.

Mode selection

There are several cleaning modes to fit various floor conditions for deep cleaning. You can make a choice with the remote control.

• You can use the remote control to switch between various modes.
• Ensure the robot is awake before starting any of the following modes. The power is on, the button light is green, and the robot is paused.

1. Auto cleaning: The most frequently used cleaning mode. Press '►II' on the main body or on the remote control. The robot plans a path and cleans along a zigzag pattern. During cleaning, the robot detects and cleans areas that have been missed.
2. Spot mode: Place the robot near the required area, and then press the '回' button on the robot to start cleaning in Spot Mode.
3. Edge mode/Classic mode:
   • Edge Mode: Press the button once to enter edge cleaning when the robot is in selected mode. (Refer to Figure 1)
   • Classic Mode: Press the button twice to enter classic cleaning when the robot is in selected mode. (Refer to Figure 2)
4. MAX mode: It is suitable for environments where the whole ground is dirty and with more dust. Press the '▼' button of the remote control to increase the suction of the robot. Press the '▲' button again to switch to normal suction.
5. Auto charge mode: The robot can sense lower power during the cleaning process and automatically activate Self-charge Mode and search for the charging dock. You can also use the '回' button on the remote control to command the robot to activate the mode.

Schedule mode

To offer a complete automatic cleaning experience, the robot receives preset cleaning schedules. Set the local time and schedules with the remote control. The robot will start cleaning automatically at the preset time every day.

Before setting local time and cleaning schedules, make sure the '►II' is on the main body is switched on. A green flashing light indicates the robot is activated from Sleep mode. To activate the robot, tap '►II' on the main body or '►II' on the remote control.

1 Set local time with remote control

Tap the 'L' button. The remote control display will show '00:00' and flashing '00:00'. Adjust time with the '▲' / '▼' buttons. To set local time, press '►' to change from hours to minute. Press the '回' button to save local time. Voice announcement will confirm the completion of setting.

2 Set a schedule

Tap the 'L' button. The remote control display will show '00:00' and flashing '00:00'. Use direction buttons to adjust the schedule time. Press the '回' button to save a schedule. Voice announcement will confirm a successful schedule, and the robot will start working at the preset times.

3 Cancel a schedule

Adjust time to "00:00" and save; or turn off the power switch on the main body.

• Please pay attention to the prompt to see if the robot is successfully scheduled.
• Rescheduling is required after changing batteries in the remote control.

Water Tank Operation

The product is equipped with water tank components. If there is a demand for mopping, it is recommended to clean the area with the dustbin first. Then, change the dustbin to the water tank components to carry out the mopping work.

• ! If during the mopping process the robot is stopped to either add water or clean the mop, the robot will reset and plan a new pathway from where it started. To achieve better cleaning, it is recommended for single room use.
• When cleaning a second room, it is recommended to manually move the robot to the corresponding room and add water and clean the cloth as needed.
• Please do not use the water tank components on carpets or rugs. Please fold the edge of the rugs or block carpet areas to avoid cleaning them during the mopping mode.
• Please pay attention during the mopping mode, timely add water or clean the mopping pad. The water tank needs to be removed when adding water.
• Be sure to remove the water tank components when charging.

1 Add water

• Open the water injection cap, fill the water with the water cup, and pour the water slowly into the tank.

2 Place the mop cloth

• Close the water injection cap tightly, put on the mop cloth, and strap the two elastic bands.

3 Install water tank components

• Press the button at the end of the dustbin, remove the dustbin, and replace it with the water tank components.

4 Mop the floor

• Start any cleaning mode on demand, and the robot will perform mopping.

APP Download

Downloading the APP

The robot can be controlled by the “ILIFEHOME” app. Scan the QR code to install the app on your iOS or Android device.

Maintenance

Reminder: Please turn off the robot and unplug the charging dock when cleaning the robot and its accessories.

Side brush and suction inlet cleaning

Please clean the side brush and suction inlet when they are dirty and replace them if needed.

Dustbin and filter cleaning

Please clean the dustbin and filter after each use of the robot as instructed below.

• Remove the dustbin and check if there is any debris in the suction inlet, and then clean it.
• A primary filter is replaceable and should be washed with water after having been in use for about 15-30 days, after which it should be dried in a cool and well-ventilated place and not squeezed.
• High Performance Filter cannot be cleaned with water. To prolong the life of the filter, it can be cleaned by shaking the filter.

Cleaning mop cloth & water tank

1. Cleaning mop cloth:
   • Remove: After mopping, please remove the water tank components and the mop cloth.
   • Maintenance: Rinse and air dry the mop cloth.
2. Cleaning water tank:
   • Remove: After mopping, remove the mop cloth and the components, drain the remaining water in the water tank.
   • Maintenance: Dry the water tank by hand and then air dry it.

Sensors and charging pins cleaning

Please use a cleaning tool or soft cloth to clean the sensors or charging pins as illustrated below.

Reminder: The charging pins should be cleaned in a timely manner if they are contaminated.

Nose wheel

Make sure the nose wheel housing is not jammed by debris, otherwise the robot's cleaning performance will be affected.

1. Pull the wheel up and out vertically and clean the wheel, wheel holder, and wheel housing.

Replace accessories regularly

Troubleshooting

Error code sheet

When the robot encounters routine troubles, it will remind you by beep.

• Short tone