MOZA AY210 Force Feedback Yoke Base

01 Product Features

• MCLS Force Feedback Technology
• 9Nm Roll Force and 200N Pitch Force
• Aluminum Quick Release
• Programmable Switch Panel
• 150mm Long Pitch Travel
• High-Resolution Encoder

02 Parameters

Dimensions and Mounting:

• Overall Length: 503.4 mm
• Width: 215.8 mm
• Height: 111.28 mm
• Mounting Hole Pattern: Four M6 and four M5 holes
• Front Panel Dimensions: 243 mm width, 111.28 mm height
• Details on mounting hole spacing and port layout are provided in technical diagrams.

03 Connection Ports

The rear panel of the AY210 base features the following ports:

• Power
• Rudder (RJ 11)
• Throttle (RJ 11)
• USB-B (for PC connection)
• Instrument Screen (RJ 11)
• Panel (RJ 11)

04 User Guide

1. Securing the Yoke

Follow these steps to attach the yoke handle to the base:

1. Rotate the D-shaped head of the MOZA Force Feedback Yoke Base to the correct position as shown in the diagram.
2. Press and hold the quick release handle located on the back of the MFY Yoke Handle. Align the yoke with the connecting rod on the base.
3. After attaching the yoke, release the quick release handle. Gently wiggle the yoke to ensure it is securely mounted.
4. Once connected, power on the MOZA yoke base. The lights on the MFY yoke handle should illuminate.

Note: If the connection fails, ensure the MFY yoke handle is fully secured to the yoke base. If the lights do not turn on, check the brightness settings in the MOZA Cockpit software.

2. Securing the Yoke Base

Desktop Clamping (Requires Optional Desk Clamp):

• Attach the included extension pads to the outer sides of the protruding sections on both sides of the Yoke Base.
• Secure the desk clamp to the protruding sections of the yoke base.
• Tighten the star-shaped handle until the clamp is securely fastened to the desk, ensuring the base and clamp are stable.

The base can also be mounted onto simulator cockpits using the screw holes located on the bottom of the base.

3. Connecting to PC

• Connect the power cable to the MOZA AY210 yoke base and plug it into a 220V outlet. Press the power button briefly to turn it on (long press to turn it off). The power light will flash upon successful connection.
• Use the included USB cable. Connect the Type-B end to the corresponding port on the back of the base, and the Type-A end to your PC. If connected successfully, the power light will remain on, and the control panel lights will illuminate.

Download and install the MOZA Cockpit Software from www.mozaracing.com. For additional information and tutorial videos, please visit the official website.

05 Software Introduction

The main page of MOZA Cockpit displays the operational status of all connected devices, including the base, yoke, throttle, and rudder pedals. It also enables quick game launches.

From the left-side icon menu in MOZA Cockpit, select the MFY yoke icon to access the Yoke Settings page, where you can adjust various parameters.

06 Base Features

Cogging Torque Calibration

Click the calibration button on the interface to optimize the cogging feel and balance of the yoke handle. This process may take some time; please wait for the progress bar to complete before proceeding. During calibration, avoid touching the yoke handle to ensure accurate results.

Base Front Panel Backlight Adjustment

The AY210 base offers two modes for adjusting backlight brightness:

• Manual Mode: Adjust lighting intensity using the backlight brightness slider in the MOZA Cockpit software. Brightness levels range from 0 to 15, with level 0 turning off the lights.
• Telemetry Mode: Synchronizes backlight brightness with in-game cockpit lighting using telemetry data.

Landing Gear Light

The landing gear light is located at the top-right corner of the front panel and supports three modes: Off, Red, and Green. Brightness can be adjusted via two modes:

• Manual Mode: Adjust lighting intensity using the landing gear light brightness slider in the MOZA Cockpit software (levels 0-15).
• Telemetry Mode: Synchronizes lighting intensity with in-game cockpit lighting.

Landing Gear Status Lighting

Gear Up Position: Set the landing gear light color when the gear handle is in the UP position.

• Off: Light turns off when the gear is retracted.
• Red: Light illuminates red when the gear is retracted.

Unlocked State:

Set the landing gear light color when the landing gear is in an unlocked state.

• Off: Light remains off during the transition.
• Red: Light illuminates red during the transition.

Flap Switch Long-press Timeout

Adjust the long-press activation time for the flap switch. This setting determines how long the switch must be held to trigger the long-press function (e.g., 2 seconds).

07 Base Force Feedback Settings

Click the base icon in the sidebar to access force feedback settings. Here, you can adjust mechanical parameters and fine-tune force feedback effects through various tabs. Settings can be saved as presets using the Preset Management feature.

08 Base Reset

If you encounter issues with force feedback or axis calibration, try resetting the base by clicking the 'Reset Base' button in the interface. If problems persist, contact customer support. The reset process may take a few moments.

09 Specifications

10 Precautions

• Do not expose the device to liquids or humidity to prevent fire or electric shock.
• Avoid using the device in direct sunlight.
• Do not use MOZA flight sim gear with MOZA racing gear.
• Recommended indoor temperature: 5°C ~ 35°C.
• Monitor gaming time and take breaks for safety and well-being.
• The device is not suitable for children under 6; small accessories may pose a choking hazard.
• Children under 13 should have adult supervision.
• Do not disassemble the equipment yourself; this will void the warranty.
• Use only the factory-supplied power supply for electrical safety and user rights.
• Parts repair or replacement must be performed by officially authorized repair centers.
• Non-standard power supplies are prohibited, even if voltage data matches.
• Use only AC power from a standard wall outlet to avoid product damage.
• Do not expose the device to heat sources.
• Unplug the power cord if the device will not be used for a long time.
• If any abnormality occurs, stop use immediately and seek help from MOZA representatives or authorized repair centers.
• Stay tuned to the official website and social media for product updates.

Manufacturer Information

Manufacturer: Shenzhen Gudsen Technology Co., Ltd

Address: Room 1903-1904, Building 3, Nanshan ZhiyuanChongwen Park, No. 3370 Liuxian Avenue, Nanshan District, Shenzhen China

Web: www.mozaracing.com

E-mail: info@mozaracing.com

Made in China