Installation Guide for STREET AERO models including: s-rda-chv-06-e1, s-rda-chv-06-e1 Rear Diffuser, Rear Diffuser, Diffuser
2016-2023 Chevrolet Camaro SS (Dual Exhaust) - Rear Diffuser – Street Aero
STEP: 1 Carefully place Fin 1 and Fin 2 onto the Main Panel (Match the number on the Fin to the number on the Main Panel) Secure with Black Bolt and Black Nut Black Bolt Black Nut Black Nut x4 1 2 STREET AERO Black Bolt 2 x4 1 STEP: 2 Remove the 2 OEM Washer Bolt and Clip located under the bumper 1 Remove 2 OEM Washer Bolt and Clip STEP: 3 Mount the assembled Main Panel to the bumper by securing Mounting Bracket CT-2 to the OEM mounting hole on STEP: 2 with M6 40mm Bolt, Finishing Washer, Washer, and Nut NOTE: Reach under or to the side of the bumper to place Washer and Nut inside the bumper Align Mounting Bracket CT-3 to its correct mounting location then Mark and Pre-Drill into the bumper NOTE: Use the hole on top of CT-3 to mark the drill location NOTE: Main Panel and Mounting Bracket may need to be removed before pre-drilling Secure the Main Panel and Mounting Bracket CT-3 to the bumper with provided M6 70mm Bolt, Finishing Washer, Mounting Bracket CT-1, Washer and Nut NOTE: Reach under or to the side of the bumper to place CT-1, Washer, and Nut inside the bumper Nut x4 Washer x4 CT-1 x2 CT-2 x2 CT-3 x2 Finishing Washer x4 CT-1 CT-2 CT-3 M6 M6 Finishing 70mm Bolt 40mm Bolt Washer Washer Nut CT-1 Pre-Drill x2 CT-3 CT-2 CT-1 x2 Nut x4 Washer x4 STREET AERO M6 40mm Bolt x2 M6 70mm Bolt x2 Pre-Drill x2 CT-1 & CT-3 Mounting Nut Washer x4 x4 CT-2 x2 CT-2 OEM Mounting 2 STEP: 4 Attach and secure Mounting Bracket CT-4 and CT-5 to the Side Panel with M6 16mm Bolt, Finishing Washer, and Nut NOTE: Push the bolt all the way into the socket to prevent it from falling out Attach the Side Panel to the Main Panel with Black Bolt and Black Nut NOTE: Do Not tighten Black Bolt (you will need to remove the Side Panel to pre-drill) Mark where Mounting Bracket CT-4 and CT-5 will be mounted to the bumper NOTE: Use the hole on top of CT-4 and CT-5 to mark the drill location Pre-drill into the bumper NOTE: Side Panel and Mounting Bracket may need to be removed before pre-drilling Mount the Side Panel by securing Mounting Bracket CT-4 and CT-5 with M6 25mm Bolt, Finishing Washer, Washer, and Nut NOTE: Reach under or to the side of the bumper to place the Washer and Nut inside the bumper Repeat to install Passenger Side Panel to the Main Panel and bumper M6 16mm Bolt CT-4 x4 CT-5 CT-6 M6 25mm Bolt x4 Behind Mounting Brackets CT-4 CT-5 CT-6 Nut x8 Washer x4 Pre-Drill x4 CT-4 x2 M6 16mm Bolt x4 CT-5 M6 25mm Bolt x4 Finishing Washer x4 M6 M6 Finishing 25mm Bolt 16mm Bolt Washer Washer Nut Black Bolt Black Nut 3 CT-4 CT-6 Main Panel Black Nut x4 Side Panel Black Bolt x4 INSTALLATION GUIDE 2016-2023 Chevrolet Camaro SS (Dual Exhaust) LT (Dual Exhaust) SS (Quad Exhaust) Rear Diffuser s-rda-chv-06-e1 s-rda-chv-08-e1 s-rda-chv-09-e1 www.streetaero.com info@streetaero.comAdobe PDF library 17.00 Adobe Illustrator 27.9 (Windows)