Instructions for AIPIN models including: AP-1201, AP1201, 2A4YZ-AP-1201, 2A4YZAP1201, 2.4GHz Touch Remote RGB Controller
GUANGDONG AIPIN TECHNOLOGY CO., LTD AP-1201 LED 2.4G CONTROLLER 2A4YZ-AP-1201 2A4YZAP1201 ap 1201
RF 2.4GHZ Dimmer Wireless intuitive touch remote control Effective receiving distance nearly 30m Easy operation,16million colors changing 2.4GHz Touch Remote RGB Controller 0117 TOUCH SCREEN LEDRGB STRIP RF CONTROLLER Input Output Voltage:DC12V~24V : Total Output Current 18A + + B - + S M - - : Connec ng Setup: Remote Receiver Control Freq. 2.4G Hz RF Input DC12V~24V Power Supply 2*AAA ba ery Output 3 Channel) TX Power 6db Output current 6A(each channel) Standby Power Consump on 10uA Output Power Max 216W/432W(12V/24V) Size: L110xW53xH20mm Connec ng mode Common anode 2.4GHZ Remote Distance >20m Output gary level 256 Standby me 6 months Size: L86xW45xH23mm Opera ng Temp. -20C~55C Remote Interface: ON/OFF Turn ON/OFF the Light and the Controller Color Wheel Select the LED Light color Signal indicator light RED Light means the Remote Send signal Brightness Adjust Bu on Change the LED Light Brightness by clicking the bu ons Speed Adjust Bu on In Dynamic Mode,increase/decrease the changing speed Modes Select Bu on Select the Modes by clicking the bu on - - MS B + + - + Controller Interface: POWER1 AC POWER2 AC TO DC + DC12-24V RF 2.4GHZ Dimmer Wireless intuitive touch remote control Effective receiving distance nearly 30m Easy operation,16million colors changing TOUCH SCREEN LEDRGB STRIP RF CONTROLLER : Input Output Voltage:DC12V~24V Total Output Current 18A + + B - + S M - - Program List: (The mode is just for reference,The actual modes are by the product criterion that has been received.) No. Mode Note No. Mode 1 W Sta c Brightness Adjustable 11 W Strobeing 2 W Breathing 12 R Flashing 3 3-Colors Gradient 13 R Strobeing 4 3-Colors Breathing 14 G Flashing 5 7-Colors Jumping 15 6 3-Colors Jumping Brightness/Speed Adjustable 16 7 R/G Jumping 17 G Strobeing B Flashing B Strobeing 8 R/B Jumping 18 Y Flashing 9 B/G Jumping 19 Y Strobeing 10 W Flashing 20 Loop mode(1~19) Note Brightness/Speed Adjustable PS: R&red G&green B&blue W&white + + B - + S M - - FCC Statement This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Radiation Exposure Statement This device complies with RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.Corel PDF Engine Version 19.1.0.419