Seaview | Leaders In Mounting Solutions For Marine Electronics
Profitez des meilleurs équipements pour votre bateau
Instruction Manual for SEAVIEW models including: LTBU1ALED12 Light Bar Top, LTBU1ALED12, Light Bar Top, Bar Top, Top
Seaview Light Bar Top w/LTBLED12 Masthead Light & Threads f/GPS
Seaview Light Bar Top w/LTBLED12 Masthead Light & Threads f/GPS SEAVIEWLTBU1ALED12
Seaview Global
File Info : application/pdf, 7 Pages, 747.82KB
DocumentDocumentINSTALLATION INSTRUCTIONS For Seaview Light Bar Top: LTBU1ALED12 Refer to website for most up to date instructions and videos. WWW.SEAVIEWGLOBAL.COM SVLTP12 (12" Post) + LTBLED12 (LED nav light) PARTS INCLUDED x2 (LTBRVT) x1 (LTBU1APLID) x3 (1058PFHSMS) x1 (LTBU1APBASE) x1 x3 (101PPHSMS) x3 (10NW) TOOLS NEEDED /16 inch = 5mm Sudbury Elastomeric Marine Sealant is recommended. To purchase call 800-6557922 or visit www.seaviewglobal.com 1 1 Drill a hole to run cables for the light. This may have already been done for you. 2 Apply marine adhesive sealant around the top of the light bar as shown, then slide on to the light bar. 3 Apply marine adhesive sealant to the mounting holes. Then insert the two plastic rivets into holes as shown. 2 4 Apply marine adhesive sealant into the groove as shown. 5 Make sure the GPS & light wires are running through the lid and down the hole into the light bar. Apply marine sealant to the bottom of the light post and then screw this to the lid and base (use screws 101PPHSMS). Make sure the light post is facing the forward position (arrow on top of the light is facing forward and the rivet hole on the light post is facing forward). Screw the lid to the base with the 3 screws provided (1058PFHSMS). Thread the GPS to the 1-14 threads on the lid. It is recommended to apply marine sealant to all the screws. Be sure the rivet hole is facing forward so the tube is in the right orientation 3 OPTIONAL ACCESSORIES Call 800-655-7922 or visit www.seaviewglobal.com for available accessories. SPREADER KIT WEDGES SP1-MOD Allows user to mount GPS units or antennas onto a Seaview Modular Mount. HINGES Compensates for plane angle. Available in 2, 4 or 6 degree wedges. Seaview Hinge Adapters fold in any direction necessary for added height clearance. 4 LTBLED12 LED Combination Masthead and All-Round White (Anchor) Light The above light is designed for use on sail or power driven vessels under 20 meters (65.6 ft.) in length operating on a nominal 12 volt system. In order to comply with `72 COLREGS and U.S. Inland Rules, the following must be adhered to: MOUNTING INFORMATION Read all instructions before proceeding. 1) These instructions show the orientation of each light. For proper light selection, positioning and configuration, refer to A.B.Y.C. Standard A-16*, the `72 COLREGS and the U.S. Inland Navigation Rules* . These lights are supplied complete with 12 volt LED's. LED lights have no user serviceable parts. 2) These lights are designed to be mounted on a horizontal surface. 3) These lights are furnished for mounting such that the long dimension of the mounting base is parallel to the fore-aft centerline of the boat. 4) This light is furnished with a 3/4 inch tube and is designed to be mounted vertically into a 3/4 inch hole. 5) WIRING: Please choose from the configurations that meet your current wiring. Attach supply connections to the light making sure to wire in accordance with both A.B.Y.C. Standard E4* and U.S. Coast Guard Safety Standards for Boat Electrical Systems (33 CFR 183)*. The connection wires are coded as follows: WHITE: RED: BLACK: Steaming: Forward compartment only (masthead light) positive lead supply. Anchor: Forward compartment and aft compartment (anchor light) positive lead supply. Ground: Negative lead supply. Electrical connections are to be made such that only the forward compartment (masthead light) is energized with the other running lights (sidelights, stern lights etc.) while underway. Both compartments are energized simultaneously by themselves to create the all-round (anchor) light. 6) Make sure the top of the light is vertical during operation (see illustration) and the arrow on the top cover points ahead (not astern), with the reference mark parallel to the fore-aft centerline of the boat. *The above referenced standards can be obtained from: (1). American Boat & Yacht Council,Inc. (2). U.S. Coast Guard 613 Third Street, Suite 10 Washington D.C. 20593 Annapolis, MD 21403 (or your local C.G. office) WIRING DIAGRAMS Diagram A (Rotary Switch) +12 WHITE RED White Red Light Status Black (Ground) White (Steaming - Red (Anchor) Forward) 0 0 OFF +12 0 Steaming 0 +12 Anchor CONFIRM LIGHT MOUNTING Arrow should be pointing forward (Ahead) Diagram B (Two Switches) STEAMING +12 WHITE +12 RED ANCHOR White Red Light Status 0 0 OFF +12 0 Steaming 0 +12 Anchor +12 +12 Anchor Diagram C (SPDT Toggle Switch) STEAMING WHITE +12 RED ANCHOR White Red Light Status +12 0 Steaming 0 0 OFF 0 +12 Anchor APPROPRIATE WIRE INSTALLATION Using Waterproof Butt Connectors (not included) Step 1 Step 2 Prop. 65 Warning for California Residents WARNING: This product may contain chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. 7 Strip wire insulation 1/3 inch on both wire ends and insert into splice barrel. Step 3 Crimp the insulated connector with crimping tool. Step 4 Apply heat while rotating the connector using heat gun Allow the terminal to cool and inspect your waterproof connection Tel: 800-655-7922 www.seaviewglobal.com EUROPEAN OFFICE Tel: +33 4 94 53 27 70 www.seaviewprogress.com 1-03122023