Intelligent lighting controls | Lumos Controls
Installation Guide for lumos models including: AF10 2 Channel AC Powered 0-10V Fixture Controller, AF10, 2 Channel AC Powered 0-10V Fixture Controller, 0-10V Fixture Controller, Fixture Controller
Radiar AF10 - Installation Guide Radiar AF10 - Installation Guide The Installation guide of Radiar AF10 can be accessed here
File Info : application/pdf, 3 Pages, 4.29MB
DocumentDocumentRadiar AF10 2 channel AC powered 0-10V fixture controller with inbuilt relay FCC ID: 2AG4N-WCA2CSFN INSTALLATION AND QUICK START SHEET WARNING AND GUIDELINES!!! Read and follow all safety instructions!! DO NOT INSTALL DAMAGED PRODUCT! This product has been properly packed so that no parts should have been damaged during transit. Inspect to confirm. Any part damaged or broken during or after assembly should be replaced. WARNING : TURN THE POWER OFF AT THE CIRCUIT BREAKER BEFORE WIRING WARNING: Risk of Product Damage Electrostatic Discharge (ESD): ESD can damage product(s). Personal grounding equipment should be worn during all installation or servicing of the unit Do not stretch or use cable sets that are too short or are of insufficient length Do not modify the product Do not mount near gas or electric heater Do not change or alter internal wiring or installation circuitry Do not use product for anything other than its intended use WARNING - Risk of Electric Shock Verify that supply voltage is correct by comparing it with the product information Make all electrical and grounded connections in accordance with the National Electrical Code (NEC) and any applicable local code requirements All wiring connections should be capped with UL approved recognized wire connectors All unused wiring must be capped Product Overview Radiar AF10, the dual-channel dimming/ tunable AC fixture controller is a part of the Lumos Controls ecosystem. The device is easy to mount in an electrical junction box or compatible fixtures. The device has dual channel 0-10V independent output to control intensity and correlated color temperature(CCT) and it has a 0-3 VDC input channel and 12VDC aux output to integrate with third-party sensors. Do's Installation should be performed by a qualified electrician Installation shall be in accordance with all applicable local and NEC codes Turn the power OFF at circuit breakers before wiring Observe the correct polarity of output terminal Don'ts Don't use outdoors Avoid input voltage exceeding maximum rating Don't disassemble the products - Specifications Input voltage Input current Load voltage Load current Aux voltage Dimming output Dimming current Dimming range Sensor input Operating temperature Dimensions Case Temperature Value Remarks 120-277VAC 3.10A 120-277VAC Rated input voltage @Max RF transmtting 3A 12VDC 0-10VDC 10mA 0-100% 2channels , Tolerance + 2%, Source current per channel 1000 steps resolution 0-3VDC Current: 1mA -30 to 55°C (-22 to 122°F) 3.22 x 1.71 x 1.25 (inch) L x W x H 81.79 x 43.43 x 31.75 (mm) 80°C (176°F) Required tools & supplies Black White Red Yellow Brown Purple Orange Pink Line Common neutral Load 12VDC 0-3VDC Sensor input 0-10V Dimming[DIM1+] 0-10V Dimming [Dim2+] DIM-/GND Electrical pliers Screwdriver Wire nuts Electrical box ½ inch trade size cable connector INSTALLATION INSTRUCTIONS Mounting Steps- Standard Install the electrical box as per the local, state & national electrical codes and requirements Turn the power OFF at circuit breaker and ensure the power is OFF before wiring Use electrical screw driver to remove three ½ inch Knock Out (KO) from the junction box Remove the locknut from the Radiar AF10 chase nipple Take in the wires and chase nipple of the Radiar AF10 through knock out(KO) hole Install the washer and locknut on to the chase nipple. Use a plier to additionally tighten and fix the device firmly with the junction box. (Note: Ensure the antenna faces towards the floor for better communication) Take the AC line and neutral mains wires through another KO hole of junction box connect the line(black) and neutral wires(white) of the fixture controller with the line and neutral wires from mains Take the line, neutral, dimming wires from the driver in to the J-box through another knockout hole To power the driver, connect the Load (Red color) of Radiar AF10 with Input Line of driver and common neutral (White color) with input neutral of driver Connect the dimming wires of the driver to the dimming wires of the controller Close the electrical box with cover plate Restore power to the circuit breaker Mounting Steps- Plenum Spaces Install the electrical box as per the local, state & national electrical codes and requirements Turn power OFF at circuit breaker and ensure the power is OFF before wiring Use electrical screw driver to remove Knock Outs from the airtight junction box (In jurisdiction where airtight box is needed, use corresponding variants of airtight junction box) Remove the locknut from the Radiar AF10 chase nipple Place Radiar AF10 inside the junction box and feed the wires and chase nipple of the device through knock out(KO) hole Install the washer and locknut on to the chase nipple and hand tighten to the wall of junction box Open the connector and take out the wire antenna and insert in to the connector Take the AC line and neutral main wires through another KO hole of junction box and connect the line(black) and neutral wires(white) of the fixture controller with the line and neutral wires from mains Take the line, neutral, dimming wires from the driver in to the junction-box through another KO hole To power the driver, connect the Load (Red color) of Radiar AF10 with Input line of driver and common neutral (White color) with input neutral of driver Connect the dimming wires of the driver to the dimming wires of the controller Close the electrical box with cover plate Restore power to the circuit breaker Wiring diagram Install the electrical box as per the local, state & national electrical codes and requirements 1. Configuring Radiar AF10 for dimming, tuning and an external sensor control L Radiar AF10 WCA2CSFN N Line DRIVER Neutral DIM1+ DIM2+ DIM LED + LED - 0-3V 12V SENSOR GND Line (Black) Neutral (White) Load (Red) 12V DC (Yellow) DIM - (Pink) 0-10V DIM2+ (Orange) 0-10V DIM1+ (Purple) 0-3V Sensor input (Brown) 2. Configuring Radiar AF10 for dimming, tuning and an external sensor control (with additional surge protection) L N E SPD L N GND Radiar AF10 WCA2CSFN Line DRIVER Neutral DIM1+ DIM2+ DIM LED + LED - 0-3V 12V SENSOR GND Application Driver Motion sensor LED fixture AC lines Junction box Radiar AF10 WCA2CSFN Troubleshooting When returning from a Power Outage, lights go back to ON state. There is a delay for the device to turn on/off/dim Lights flickering Lights did not turn ON This is normal operation. Our device has a fail-safe feature forcing the device to go to 50% or 100% and 0-10V at the full output on the loss of power. Alternatively, the device will return to its previous state after the power is restored, as configured using the Lumos Controls mobile app needs to be updated to Alternatively, the device will return to the previous state or a custom state as configured using the Lumos Controls mobile app after the power is restored Check whether you have set up a transition time Check whether connection is as per wiring diagram Check for loose connections Check whether circuit breaker has tripped Check whether fuse has blown Check for loose connections Commissioning Once powered up, the device will be ready to be commissioned via the Lumos Controls mobile app, available for free download on iOS and Android. To begin commissioning, click the `+' icon from the top of the `Devices' tab. The app allows you to preset certain configurations which will be loaded after the device is added. The pre-configurations made using 'Commissioning Settings' will be sent to the devices being commissioned. Once commissioned, the device will be displayed in the `Devices' tab and you can perform individual operations like ON/OFF/dimming on it from this tab. Note: The `Output Channel Configuration' will be `Single Channel' by default. To configure dual channel settings, go to `Additional Settings' and click `Output Channel Settings'. Then select `Controller based color tuning' or `Driver based color tuning' based on the connected driver. Please visit Help center for more details Warranty 5-year limited warranty Please find warranty terms and conditions Note: Specifications may change without notice Actual performance can vary due to end-user environment and application Lumos Controls Application Download the `Lumos Controls' application from Play Store or App Store OR Scan the QR codes to download the `Lumos Controls' application The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by WiSilica Inc. is under license. Other trademarks and trade names are those of their respective owners. 20321 Lake Forest Dr D6, Lake Forest, CA 92630 www.lumoscontrols.com +1 949-397-9330 All Rights Reserved WiSilica Inc Ver 1.1 Jul 2022