FORIOUS Multi-Function Shower Panel
Simple & Luxury
To Get Started
- Before you begin, read all instructions carefully. This manual is a graphic reference for installation purposes. Some graphic elements and components may differ.
- Inspect unit carefully to ensure there is no damage or defects. If such is the case, please contact FORIOUS customer service.
- Make sure you have received all parts (tools not included).
- Consult local building codes to ensure that installation complies with standards in your area.
WE STRONGLY SUGGEST YOU LET A SPECIALIST PROCEED WITH THE INSTALLATION.
Installation Steps
Step 1: Rain shower and Body shower panel connect
Follow the diagrams for connecting the rain shower and body shower panel components. Ensure all connections are secure.
Step 2: Handheld shower holder installation
Install the handheld shower holder according to the provided illustrations. Ensure it is mounted securely.
Step 3: Measurement
Adjust the plumbing to ensure adequate space for the shower. Establish the precise height and position of the unit on the wall.
Recommendations:
- Leave a 10" (25 cm) space between the shower head and the average height of people.
- Maintain a minimum distance of 1" (2.5 cm) from the ceiling.
Diagram illustrating recommended height placement relative to a person and ceiling.
Step 4: Mounting Brackets Installation
Measure and mark the wall for bracket placement. Drill holes (Ø6.0mm) and install the mounting brackets using screws and anchors. Ensure the brackets are level.
WARNING: HOSES BENT IS NOT ALLOWED, IT WILL CAUSE NO WATER SUPPLY!
Step 5: Water supply checking and supply hoses connection
Connect the hot and cold water supply hoses. Use sealing tape on threaded connections to prevent leaks. Check for any water leakage after connections are made.
Step 6: Hand shower connection
Connect the handheld shower hose to the shower panel and the handheld shower head. Ensure a secure connection.
Step 7: Battery Box Installation
Install the battery box for the LED display. Insert 2 AA batteries. Ensure correct polarity.
Step 8: Test
- Check for no water leakage at any connection.
- Verify that all shower modes work correctly.
Usage Guide
LED Switch: Control the LED features.
DIVERTER KNOB: Use to switch between shower functions (e.g., rainfall, handheld, jets).
TEMPERATURE CONTROL: Adjust the water temperature.
Diagrams showing the operation of the diverter knob and temperature control.
Care and Maintenance
- Wipe with a soft towel after each use. Use mild dishwashing detergent to keep surfaces bright and clean. Rinse well and dry with a clean cloth.
- Powdered detergents and abrasive liquid cleaners may damage surfaces.
- Do not allow the surface to come into contact with corrosive products such as acetone, nail polish remover, dry cleaning solution, lacquer, paint thinner, gasoline, or etc.
- Any cleaning product should be tested on an inconspicuous surface before using to clean.
More Design
The shower panel designs may vary; this instruction is for reference for installation and usage. Specific operations are subject to the actual shower panel.
Technical Data
- Operating pressure: Max. 1MPa
- Recommended operating pressure: 0.22-0.5MPa
- Test pressure: 1.5MPa (1MPa=10bar=147 PSI)
- Hot water temperature: Max. 176°F
- Recommended hot water temperature: 149°F
- Connections (cold right-hot left): G1/2
Parts List
- 1: Rain panel body*1 Pcs
- 2: Shower panel body*1 Pcs
- 3: Handheld shower*1 Pcs
- 4: Mounting brackets, Screws and anchors*2 Sets
- 5: Handheld shower holder*1 Set
- 6: Hose for handheld shower*1 Pcs
- 7: 90 Degree hose connector G1/2*2 Pcs
- 8: Gasket*2 Pcs
- 9: Teflon Tape*1 Pcs
- 10: White gloves*1 Pair
- Additional components: Screw anchor*4 Pcs, Screws*4 Pcs, Hose clamp*2 Pcs, Screws set*4 Pcs, Mounting brackets*2 Pcs (Rain panel & Shower panel screws)
Diagram illustrating all included parts.
Recommended Tools for Installation
- Screwdriver
- Hammer
- Pencil
- Level
- Drill Bit 6mm
- Electric Drill
- Wrenches
- Sealing Tape
