SWT3-31-HU-TR 3x1 4K60 USB–C/HDMI Switcher Extender
User Guide for kramer models including: SWT3-31-HU-TR 3x1 4K60 USB C HDMI Switcher Extender, SWT3-31-HU-TR, 3x1 4K60 USB C HDMI Switcher Extender, USB C HDMI Switcher Extender, HDMI Switcher Extender, Switcher Extender, Extender
Application Diagrams - Kramer Electronics
Купить SWT3-31-HU-TR Автокоммутатор 3х1 интерфейса USB-C и 2x HDMI/USB, 4K60 (4:4:4), вход/выход HDBaseT, деэмбеддер аудио | СНК-С | Дистрибьютор ProAV
File Info : application/pdf, 4 Pages, 1.30MB
DocumentDocumentSWT3-31-HU-TR Quick Start Guide Scan for full manual This guide helps you install and use your SWT3-31-HU-TR for the first time. Go to www.kramerav.com/downloads/SWT3-31-HU-TR to download the latest user manual and check if firmware upgrades are available. Step 1: Check what's in the box SWT3-31-HU-TR 3x1 4K60 USB-C/HDMI Switcher Extender 1 Power adapter and cord 1 Multi signal USB-C cable (1m) 4 Rubber feet 1 Quick start guide Step 2: Get to know your SWT3-31-HU-TR Configuring the device as transmitter (Tx) or receiver (Rx, default) is done via the embedded webpages settings. # Feature Function 1 USB-C IN 1 Port Connect to USB-C AV sources: · that support DisplayPort Alternate Mode, for example, a laptop) to share content. · to communicate with the USB devices (for example, a PTZ camera) that are connected to the device, · to connect to the LAN · to charge the connected sources (that supports USB Power Delivery 2.0). 2 IN Status LED 1 to 3 (per input port) While charging, the charging icon (to the right of the connector) becomes visible and lights orange. LED Status Indicates Lights blue An input is selected and connected with an active AV or AV+USB source. Flashes blue An input is selected and has no active AV signal. Lights green An input is selected and connected with an active USB host only (no AV). Off An input is not selected and has an active AV signal. 3 IN Ports HDMI Connect to an HDMI source. 4 (2 and 3) HOST USB B Connect to a USB host (for example, a room PC) to communicate with the USB devices (for 3.2 Connector example, a PTZ camera) connected on this device. 5 INPUT SELECT Button Press to select an input. Each press toggles to the next input. 1-3 inputs for Tx mode, 1-4 inputs for Rx mode. 6 DISPLAY ON Button 7 PoE LED Press to turn display On/Off. Button LED lights on sending Display On message. Button LED turns off on sending Display Off message. Lights green when the device provides PoE to a connected device. SWT3-31-HU-TR Quick Start P/N: 2900- 301704QS Rev: 3 # Feature 8 NET LED 9 STATUS LED Function LED Status Dark Lights green Flashes green for 60 seconds LED Status Dark lights white Lights blue Lights green Indicates No IP address acquired. A valid IP address has been acquired. A means to identify the device in a system, using command #IDV. Indicates Power is off PoE powering is active. Power is on and a source is connected. Power is on, and a source and an acceptor are connected. # Feature Function 10 HDBT PoE RJ-45 Connector Connect to the HDBT RJ-45 connector to a paired receiver (when set to OUT on Tx mode) or transmitter (when set to IN on Rx mode) device that receives or provides PoE (for example, EXT3-21-XR-TR). HDBT provides PoE only when the device is PSU-powered. HDBT is IN 4 on Rx mode. 11 HDMI OUT Connector Tx Mode: Connect to a local HDMI acceptor (for example, a monitor). Rx Mode: Connect to an HDMI acceptor. 12 USB DEVICE A 3.1 Port (1 to 3) Connect to the USB local devices (for example, a USB camera, a soundbar, microphone and so on). 13 IR 3.5mm Mini Jack Connect to an IR emitter or sensor cable for IR extension over HDBT, or IR emitter for IR signal output per command from LAN-connected controller (for example, from KC-VB1). 14 AUDIO OUT 5-pin Terminal Connect to a balanced stereo analog audio acceptor. Block Connector 15 I/O 3-pin Terminal Block Connect to: (S1 to S2) (GND is common for I/O and RS-232). · Input-triggering devices (for example, remote buttons or sensors), OR · Output-triggered devices (for example, remote alarm LED indication). Each of these GPIO ports may be configured as a digital input, digital output, or an analog input port. 16 RS-232 3-pin Terminal Block · Connect and control the SWT3-31-HU-TR unit (default). · Connect to an RS-232 controlled device (for example, the connected PTZ USB camera) to be controlled via an IP-connected controller (for example, SL-240C). 17 1G LAN PoE RJ-45 Connector Connect to LAN. The device accepts power from the LAN port. 18 20V DC Power Connector Use the included +20V 6A power supply for powering the unit and charging the source device connected to the USB-C port. 19 RESET Recessed Button For restoring factory default settings, press the RESET button and connect power to device (keep pressing longer than 6sec after power connection). Step 3: Mount SWT3-31-HU-TR Install SWT3-31-HU-TR using one of the following methods: · Mount device with its recommended mounting accessory to the underside of the table and secure. · Mount the unit in a rack using the recommended rack adapter (see https://www.kramerav.com/SWT3-31-HU-TR). · Attach the rubber feet and place the unit on a flat surface. · Ensure that the environment (e.g., maximum ambient temperature & air flow) is compatible for the device. · Avoid uneven mechanical loading. · Appropriate consideration of equipment nameplate ratings should be used for avoiding overloading of the circuits. · Reliable earthing of rack-mounted equipment should be maintained. · Maximum mounting height for the device is 2 meters. Step 4: Connect inputs and outputs Always switch OFF the power on each device before connecting it to your SWT3-31-HU-TR. Regarding power options, see next section. Connecting the audio output To a balanced stereo audio acceptor: To an unbalanced stereo audio acceptor: Step 5: Connect power Power the device via the LAN or HDBT port. Use the supplied 20V power adapter to power the device and enable the USBC port to charge its connected devices. Safety Instructions (See www.kramerav.com for updated safety information) Caution: · For products with relay terminals and GPI\O ports, please refer to the permitted rating for an external connection, located next to the terminal or in the User Manual. · There are no operator serviceable parts inside the unit. Warning: · Use only the power cord that is supplied with the unit. · Disconnect the power and unplug the unit from the wall before installing. Step 6: Operate SWT3-31-HU-TR Operate SWT3-31-HU-TR via: · Front panel buttons. · Remotely, by IP or RS-232 serial commands transmitted by a touch screen system, PC, or other serial controller. · Device web pages via the IP client connection. RS-232 Control / Protocol 3000 Baud Rate: 115,200 Parity: None Data Bits: 8 Command Format: ASCII Stop Bits: 1 Example: (flash LEDs on the front panel for 60 seconds): #IDV<CR> Default IP Parameters DHCP ON Fallback IP Address: Subnet mask: Gateway: Factory Reset 192.168.1.39 255.255.255.0 192.168.0.1 UDP Port #: TCP Port #: User/Password 50000 5000 Admin/Admin Protocol 3000: "#FACTORY" command. After receiving "FACTORY OK" perform one of the following to restart the device and complete the procedure: · Power cycle · Send command "#RESET" Web Pages: In the Settings page, click Factory Reset. The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.