User Manual for Bartscher models including: TR I3WL1350 Heat Bridge, TR I3WL1350, Heat Bridge, Bridge
Calentador para Buffet Bartscher TR I3WL1350
PCI/4711 - PCI/4712 - PCI/4713 WARMING SURFACES WITH INFRARED LAMPS CONTENTS 1 GENERAL INFORMATION Purpose of the manual................................ 4 Manufacturer and machine identification......... 4 Warming surfaces with infrared lamps description................................................ 5 Technical specifications............................... 5 Overall dimensions..................................... 5 Safety information....................................... 6 3 USE AND CLEANING INFORMATION Control descriptions..................................... 8 Recommendations for use ........................... 8 Warming surfaces with infrared lamps use....... 8 End of the day cleaning ............................... 8 Extended periods of disuse ........................... 8 2 INSTALLATION INFORMATION Packaging and unpacking............................ 7 Installation area......................................... 7 Electrical connections ................................. 7 4 TROUBLE SHOOTING, RECYCLING Introduction................................................ 9 Problems, causes, solutions.......................... 9 Disposal and recycling................................. 9 ATTACHMENTS Spare parts catalogue Wiring diagram 1 GENERAL INFORMATION Purpose of the manual This manual was written by the Manufacturer and is an integral part of machine equipment. During design and construction the Manufacturer has carefully considered possible hazards and personal risks that may result from interaction with the machine. In addition to observing the specific laws in force, the manufacturer has adopted all "exemplary construction technique principles". The purpose of this information is to advise the users to use extreme caution to avoid risks. However, discretion is invaluable. Safety is also in the hands of all the operators who interact with the machine. Keep this manual in a suitable place, always within reach for consultation. The following symbols are included to better stress some passages: DANGER WARNING: indicates hazards that may cause serious damages; attention is required. INFORMATION: indicates particularly important technical information. The following is enclosed with this manual: - Warranty certificate describing the Manufacturer's warranty conditions. - Documents that prove conformity with effective health and safety laws. Contact the Authorised dealer for any service request, information or spare parts order. Manufacturer and machine identification Manufacturer Identification Machine model Technical specifications Conformity markings Serial number 4 1 GENERAL INFORMATION Warming surfaces with infrared lamp description This product is specifically designed to keep the temperature of food placed over the heating surfaces constant. It is characterised by a highly simplified construction in order to reduce the possibility of malfunctions to a minimum and facilitate maintenance. The heating surface is fully constructed with stainless steel AISI 304 18/10 with galvanized steel sheet metal bottom cover. The resistance is attached under the heating surface. The heating surface is distinguished by infrared lamps placed above the surface to increase its already high heating capacity. 4 rubber feet can be applied to the bottom of the heating surface for support and insulation. Controls to turn on the machine and set temperature are found on the long side of the surface. Technical specifications Descriptions Power supply Nominal power Net weight Packaged weight Installation Protection level Electrical shock protection Unit of measure V Hz Ph W Kg Kg Conformity with directives and norms PCI 4711 500 10 14 PCI 4712 230V 50Hz 1Ph 1000 17 22 Counter IPX4 PCI 4713 1500 25 30 Class I 73/23/EEC - 93/68/EEC 93/44/EEC - 89/336/EEC 89/109/EEC Overall dimensions mm A B C PCI4711 60 50 85 PCI4712 65 85 85 PCI4713 70 125 85 mm A B C PCI4711 460 510 780 PCI4712 620 860 780 PCI4713 620 1270 780 5 1 GENERAL INFORMATION Safety information · Careful consultation of this manual before installation and use is essential. Continual observance of the indications found in the manual guarantee personal and machine safety. · Never tamper with safety devices for any reason. · Strict observance of the work safety regulations issued by the responsible organisations in each country is strongly recommended. · The manufacturer is not liable for damages to persons or things due to the neglect of safety regulations. · Correct machine placement, illumination and cleanliness are important conditions for personal safety. · Do not expose the machine to the elements. · Machine connections and start-up must only be performed by qualified technicians. · Make sure that the system specifications of the room where the machine is installed correspond to the information printed on the plate. · Make sure the machine is connected to a grounding system. · The work area around the machine must always be kept clean and dry. · Use the garments foreseen by work safety regulations. · This machine must only be used for its specific purpose; any other use is considered improper and therefore hazardous. · Do not overload the machine. · Introducing objects, tools, hands or other within hazardous parts is forbidden. · Keep the machine away from children. · Disconnect the power cord from the electrical socket when the machine is not in use. · In the event of malfunctions and/or problems, do not attempt to repair the machine. Contact the authorised dealer. · Use original spare parts. · Before cleaning the machine, disconnect the power supply by unplugging the machine. · Do not clean with running water. 6 2 INSTALLATION INFORMATION Packaging and unpacking The machine is packaged in cardboard with polystyrene inserts to guarantee full integrity during transport. · Handle the packaging according to the instructions. · Open the packaging and check the integrity of all components. Keep packaging for future moves. · Lift the machine as indicated and place it in the installation area. Installation area The arranged area must be suitably illuminated and an electrical socket must be available. The resting surface must be sufficiently ample, even and dry. The machine must be installed in rooms with non-explosive environments. In any case, installation must also be performed in consideration of the work safety laws in force. Room conditions table Descriptions Working temperature Storage temperature Relative humidity Dustiness Values 0÷35 °C (32÷95 °F) -15 to +65 °C (from 6.8 to +149 °F) Maximum 80% with 20 °C room temperature Maximum 50% with room temperature between 20÷60 °C Less than 0.03 g/m³ Electrical connections DANGER WARNING: Electrical connections to the supply mains must be performed by qualified personnel. Verify the efficiency of the grounding system in the building. Make sure that line voltage (V) and frequency (Hz) correspond to those of the machine (See the identification plate and wiring diagram). The machine is equipped with a power cord that connects to a multi-polar plug. The plug is to be connected to a wall switch equipped with a circuit breaker. Connection single-phase 230V 1Ph 7 3 USE AND CLEANING INFORMATION Control descriptions - Indicator light (B) - Adjustable thermostat 0°- 90°C (C) - Loaded circuit breaker (A) with tension led - Power cord inlet (D) + cord Recommendations for use Before using the machine remove, if found, the special protective film. Unpleasant odours produced during the first minutes of operation are due to the presence of processing grease residues. On first use, heat the machine to the maximum temperature. Warming surfaces with infrared lamps use Connect the power cord to the main switch and turn the thermostat graduated knob to set the desired temperature. The led will stay on until the surface reaches the previously set temperature. End of the day cleaning · Remove the plug from the electrical socket at the end of the day. · Accurately clean using neutral products. · Clean external machine parts with a damp sponge when the machine is fully cooled. · Do not use metallic pads and abrasive detergents. · To avoid hazards caused by contact with high temperature parts, only access heating parts after maintenance operations have been completed. Extended periods of disuse For extended periods of disuse, turn off the main wall switch, clean the machine and cover it with a cloth to protect if from dust. 8 4 TROUBLE SHOOTING, RECYCLING Introduction In the event of breakdown or malfunctioning, disconnect the plug from the socket and contact your Dealer's service centre. Avoid dismantling internal machine parts. The manufacturer is not liable for any machine tampering! Problems, causes, solutions Problem Cause Main switch off The machine does not heat No voltage on the power supply Resistance broken Solution Turn on main switch Contact your dealer's service centre Contact your dealer's service centre Disposal and recycling The machine was designed and constructed to work for an average of 10.000 hours. When finished using the machine, follow national laws for disposal and recycling. Please contact the environmental authorities or authorised organisations. 9Bullzip PDF Printer / www.bullzip.com / Freeware Edition