User Manual for SYNCO models including: G2A1 Microphone, G2A1, Microphone
SYNCO Wireless Microphone | SYNCO
Portable Wireless Microphone SYNCO G2(A1) | SYNCO
Caring For Your SYNCO Product · Please keep the product in a dry, clean, dust-free environment. · Keep corrosive chemicals, liquids and heat source away from the product to prevent mechanics damage. · Use only a soft and dry cloth for cleaning the product. · Malfunction may be caused by dropping, impact of external force. · Do not attempt to disassemble the product. Doing so voids warranty. · Please have the product checked or repaired by authorized technicians if any malfunctions happened. · Failure to follow all the instructions may result in mechanics damage. · Warranty does not apply to human errors. Package List Product Instruction 1. TX Transmitter External Mic Input Type-C Charging Port On/ Off Button Built-in Mic Display Screen Noise Reduction Gain Adjustment of TX Magnet Pocket Clip RX Receiver x1 TX Transmitter x1 Carrying Bag x1 Microphone G2A1 User Manual Thank you for choosing SYNCO product. Please read this manual carefully before use and follow all instructions mentioned herein. 2-in-1 Charging Cable x1 External Lav Mic (With Wind Muff) x1 3.5mm TRRS Phone Cable x1 3.5mm TRS Camera Cable x1 Mic Windshield x1 Magnet x1 User Manual X1 2. RX Receiver Type-C Charging Port / Digital Output On/ Off Button (Mono / Stereo / Safety Channel) 3.5mm TRS Output 3.5mm Monitoring Port Display Screen Gain Adjustment of TX A Gain Adjustment of TX B Magnet Pocket Clip 3. Display Screen Recording Muting Noise Reduction on TX Transmitter Power Indicator Disconnected Connecting Connected Audio Dynamic Display Recording Mode: Mono/ Stereo/ Safety TX A Gain of TX A Audio Dynamic Display of TX A RX Receiver Power Indicator TX B Gain of TX B Audio Dynamic Display of TX B Operations 1. Power On/ Off Power On The TX and RX automatically turn on when long press the power button for 3 seconds, and the display screen lights up. Power Off The TX and RX automatically turn off when long press the power button for 3 seconds, and the display screen lights off. 2. Pairing Automatic Pairing Automatically pairing after the TX/RX turns on. Manual Pairing Long press the transmitter and receiver at the same time for 3 seconds to power off . After shutdown, long press the power button of the transmitter and receiver for 8 seconds at the same time to enter the [connecting ] state. Disconnected Connecting Successfully Connected show as the picture Connected *Note: Before successful connection, the transmitter channel displays A by default. The transmitter connected to the receiver first is the transmitter A, and the later one is the transmitter B. 3. Channel output connection 3.5mm OUT output The receiver outputs the audio signal to the recording device via either a 3.5mm TRRS phone cable or a 3.5mm TRS camera cable. Please use the appropriate cable according to your device. 3.5mm TRS Camera Cable 3.5mm TRRS Phone Cable Apple Adapter (With MFI Certification) *Note: When using an external microphone, please insert it correctly into the microphone input jack. Only TRS interface microphones are supported. Type-C port digital output The receiver Type-C port has a digital output function, which can directly use the Type-C to Type-C cable to output mobile phones or computers and other devices. *Note: When connecting the computer, enter the sound Settings and set the input microphone to SYNCO G2Pro to use G2 recording; Set the output speaker to SYNCO G2 Pro to use real-time ear return in the receiver listening interface. 4. Real-time monitoring The 3.5mm monitoring port of the receiver supports digital monitoring, which can simultaneously monitor the sound source of the transmitter and the input sound source of the device. 3.5mm Monitoring Jack Headphone Impedance: under 100 5. Volume Control Press the power button on the TX to turn on/off the mute. Short press the gain adjustment button of the TX to adjust the volume for 6 levels (0-3-6-9-12-15). Short press the gain adjustment of A/B TX buttons on the RX to adjust the volume of A/B TX. 6. Noise Cancellation Short press the noise cancellation button on the transmitter to switch between noise-control modes: Noise Cancellation Off Low-Level Noise Cancellation High-Level Noise Cancellation High-Level Noise Cancellation Low-Level Noise Cancellation Noise Cancellation Off 7.Switch the Channel Mode Short press the power button on the RX to switch the mono/stereo/safety channel mode. Default mono mode. 8.Charging Connect the charging cable through Type-C port of TX and RXand fully charged in about 2 hours. ( Note: The grey end of the 2-in-1 charging cable included in the package can be used for digital output. ) 9. Mic Windshield & Device Installation Screw to mount the windshield. TX RX 10.Setting The Recording Level Correctly Camera devices generally have poor-quality, noisy preamps. In order to get the cleanest signals possible, it is highly recommended that you set the recording level on your camera quite low, 1/2 or 1/3 of it. G2 provides variable gain control, allowing you to tailor your levels to just about environment and recording device. Adjust the recording level of inbuilt mics for SONY Camera (Take A7S for example) Adjust the recording level of inbuilt mics for Canon Camera (Take EOS 5D Mark for example) Adjust the recording level of inbuilt mics for Panasonic Camera (Take LUMIX GH5 for example) Specifications TX Transmitter Wireless Transmission RF Frequency Band Working Distance Mounting Audio Input Power Requirements Battery Type Battery Charging Time Battery Life Display Screen Dimensions Material Weight Digital 2.4GHz 2400-2483.5MHz 656ft/200m (LOS area), 164ft/50m (NLOS area) Pocket Clip 3.5 mm TRS Mic Input 5V 1A Built-in Lithium Battery, 400mAh 2H 8H TFT Screen 52X42X17mm ABS 39g RX Receiver Wireless Transmission RF Frequency Band Working Distance Latency Mounting Number of Audio Channels Audio Output Volume Adjustment Power Requirements Battery Type Battery Charging Time Battery Life Display Screen Dimensions Material Weight Microphone Form Factor Frequency Range Sensitivity Maximum SPL Digital 2.4GHz 2400-2483.5MHz 656ft/200m (LOS area) 164ft/50m (NLOS area) 20ms Pocket Clip 2 3.5 mm TRS Mic Output 3.5 mm TRS Headphone Output Type-C Output 6 levels (0-3-6-9-12-15)/(0~30dB) 5V 1A Built-in Lithium Battery, 400mAh 2H 8H TFT Screen 52X42X17mm ABS 39g Built-in/External Mic 50Hz-20KHz -35dB±3dBre 1V/Pa at 1 KHz 120dB SPLat 1KHz Warranty Warranty Period Thank you for purchasing SYNCO products. 1. Customers are entitled to free replacement or repair service in case of quality defect(s) found in the product under normal use within 30 days upon receipt of the product. 2. Original SYNCO products are entitled to 12-month limited warranty service. The warranty period begins on the date of purchase of brand new, unused products by the first end-user. Within the warranty period, if product defect or failure is attributable to material defection or technological problem, the defective product or defective part will be repaired or replaced without charge (service and materials fee). Warranty Exclusions and Limitations Faults resulted from inappropriate use of a product without following its operation specification 1. Artificial damage, e.g. crash, squeeze, scratch, or soaking 2. Modifications to a product by its user or a third party without prior written consent of SYNCO, e.g. replacement of element or circuit, label alteration 3. The code on product is inconsistent with that of warranty certificate, or the code on the product or warranty certificate is altered or torn off 4. All consumable accessory attached to a product, like cable, wind muff, battery 5. Faults as a result of force majeure, such as fire, flood, lightning, etc. Warranty Claim Procedure 1. If failure or any problem occurs to your product after purchase, please contact a local agent for assistance, or you can always contact SYNCO's customer service through email at support@syncoaudio.com. 2. Please retain your sales receipt and warranty certificate as proof of purchase. If any of these documents is missing, only sales return or chargeable service will be provided. 3. If the SYNCO product is out of the warranty coverage, the service and the parts cost will be charged. WARRANTY CERTIFICATE Product Model: Date of Purchase: Serial Number: Malfunction Description : Buyer Name: Buyer Telephone : Buyer Mail : Buyer Address : Dealer : Dealer Telephone : Delivery Date : Cause of Malfunction : Maintenance Personnel : Malfunction Processing : *Please register your warranty. Meanwhile, you are welcomed to contact us via Email support@syncoaudio.com Guangzhou Zhiying Technology Co., Ltd Room 2401, 24 / F, South Tower, Lisheng Plaza, No. 68 Huadi Avenue, Liwan District, Guangzhou, China, 510000 support@syncoaudio.com www.syncoaudio.cnAdobe InDesign 15.1 (Windows) iLovePDF