产品中心 - 芯明天-压电纳米定位与控制系统制造商
User Manual for COREMORROW models including: E63.A1K Series Piezo Controller, E63.A1K Series, Piezo Controller, Controller
Small-Size Piezo Controllers,Piezo Controllers,Piezo Amplifiers,Piezo Drivers,Pi
Declaration! This user manual is a integrated user manual of the E63.A1K series piezoelectric controller. Please read this user manual carefully before using this controller.
File Info : application/pdf, 7 Pages, 481.60KB
DocumentDocumentE63.A1K Series Piezo Controller User Manual Version: V1.0 This document describes the following products: E63.A1K Open loop 1 channel DECLARATION Declaration! This user manual is a integrated user manual of the E63.A1K series piezoelectric controller. Please read this user manual carefully before using this controller. Follow the instructions in the manual during use. If there is any problem, please contact us for technical support. If you do not follow this manual or disassemble and modify the product yourself, the company will not be liable for any consequences arising therefrom. Please read the following to avoid personal injury and to prevent damage to this product or any other product connected to it. In order to avoid possible hazards, this product can only be used within the specified range. Notice! Do not touch any exposed ends of the product and its accessories. There is high voltage inside. Do not open the case without permission. Do not connect or disconnect input, output, or sensor cables with power on. Please keep surface of E63.A1K clean and dry, don't operate in humid or static environment. After use, output voltage should be cleared to zero before turning off the controller switch, such as switching the servo state to the open-loop state. Danger! The piezoelectric power amplifier described in this manual is a high-voltage device capable of outputting high currents, which can cause serious or even fatal damage if not used properly. It is strongly recommended that you do not touch any parts that connect to the high voltage output. Special Note: If you connect it with other products in addition to our company, please follow the general accident prevention procedures. Operating the high-voltage amplification requires training professional operators. Warning! If the voltage exceeds the PZT's tolerable range, it will cause permanent damage to the PZT. Before adding voltage to the PZT poles, it must be ensured that the positive and negative poles of the PZT are connected correctly and the operating voltage is within the allowable range of this PZT. Cautious! E63.A1K housing should be installed on a horizontal surface in an area with a 3CM air flow area to prevent internal convection in the vertical direction. Insufficient airflow can cause equipment to overheat or premature instrument damage. Contents 1. Introduction ................................................................................................................................. 2 1.1 Features ................................................................................................................................. 2 1.2 Applicaitons ........................................................................................................................... 2 1.3 Order information.................................................................................................................. 2 2.Driving Principle ........................................................................................................................... 2 3.Appearance ................................................................................................................................. 3 4.Pin Definition................................................................................................................................. 3 5.Notes and suggestions ............................................................................................................... 4 6.Customer Service ........................................................................................................................ 4 7.Contact us .................................................................................................................................... 5 E63.A1K Series Piezo Controller User Manual 1. Introduction 1.1 Features Super small size Low power consumption 15V (±0.5V) power supply Peak current 100mA Ave current 12mA Unload bandwidth 1KHz Output short circuit protection 1.2 Applicaitons Driving piezo actuators 1.3 Order information E63.A1K----1Channel Open loop Accept customized according to requirements 12bit gain/-20 120V output voltagedefault 15bit gain/-20 150V output voltage 2.Driving Principle Analog in Power amplifier High voltage output 2 3.Appearance 4.Pin Definition Pin No. 1 2 3 4 5 Housing Functions Power supply: +15VDC/0.5A Supply voltage ground and control input ground, AGND Analog voltage input Voltage output ground: SGND output Analog voltage output Shielding ground GND 3 E63.A1K Series Piezo Controller User Manual 5.Notes and suggestions E63.A1K cannot be used to drive inductive loads. If the inductive loads are driven, the product may be damaged. The highest output voltage of E63.A1K will decrease with the increase of output current, so please pay attention to it when using. The drawdown curve is as follows: Output voltageV 160 150 140 130 120 110 100 90 80 0 Voltage Drop Curve 5 10 15 20 25 Output currentmA 6.Customer Service If you have any questions in use, please tell us the following information: Product model and relevant number The controller model Software driver version Supporting computer operating system 4 7.Contact us Harbin Core Tomorrow Science & Technology Co., Ltd. Tel: +86-451-86268790 Email: info@coremorrow.com Website: www.coremorrow.com Address: Building I2, No.191 Xuefu Road, Nangang District, Harbin, HLJ, China CoreMorrow Official and CTO WeChat are below: 5