Quick Installation Guide

A. Initial Case Preparation

1. Remove the screw from the bottom side of the case. ➡️ Pull out the motherboard tray.
2. Remove the PSU and EPE Sponge.

Attach the foam pad to the indicated position on the power supply to avoid damaging the case.

B. Installing the CPU

1. Open the CPU socket lever.
2. Remove the protective cover from the CPU socket.
3. Align the CPU with the socket's triangle indicator and gently place it into the socket.
4. Close the CPU socket lever to secure the CPU.

C. Installing the CPU Fan and Heatsink

Installing the CPU Box Cooler

1. Place the CPU cooler onto the CPU, aligning mounting holes.
2. Secure the cooler using the provided screws or clips.

D. Installing Memory Modules

The DeskMeet X600 series requires DDR5 DIMM. For dual-channel configuration, install identical DIMM pairs (same brand, speed, size, and chip-type).

1. Open the clips on the DDR5 DIMM slots.
2. Align the notch on the memory module with the notch in the slot.
3. Push the memory module down firmly until the clips lock into place.

Note: Install modules in slots A2 and B2 for single module, or A1/B1 and A2/B2 for dual modules, following the motherboard layout diagram.

E. Installing the M.2 WiFi/BT Module and WiFi Antennas

1. Insert the M.2 WiFi/BT module into the corresponding M.2 slot (Key E).
2. Tighten the screw to secure the module to the motherboard.
3. Attach the SMA Wi-Fi Antenna Cables to the module's connectors.
4. Locate the antenna holes on the rear panel. Push the antenna port cover plates with a screwdriver and snap them off.
5. Insert the SMA Wi-Fi Antenna Cables into the antenna holes. Organize cable routing neatly.
6. Insert the Wi-Fi Antenna Connectors into the antenna ports on the rear panel.
7. Fasten the screw nuts to secure the antenna connectors.

F. Installing the Type 2280 Ultra M.2 SSD

1. Locate an M.2 slot on the motherboard (M2_1 for Gen5 x4, M2_2 for Gen4 x4).
2. Carefully insert the M.2 SSD into the slot at an angle.
3. Tighten the screw to secure the M.2 SSD to the motherboard.

G. Installing the Graphics Card

1. Open the PCIe slot retention clip.
2. Remove the corresponding expansion slot cover(s) from the case.
3. Align the graphics card with the primary PCIe x16 slot and press down firmly until it clicks into place.
4. Secure the graphics card to the case with screws.

Note: Installing a graphics card may limit the space for 3.5" HDDs, 2.5" SSDs, or liquid coolers.

H. Installing the 3.5" HDD

1. Connect the SATA Data and Power cables to the 3.5" HDD.
2. Locate the drive mounting position in the case.
3. Attach the HDD using screws.

Note: If you install a 3.5 inch HDD, you will not be able to install a graphics card.

I. Installing the 2.5" HDD/SSD

1. Connect the SATA Data and Power cables to the 2.5" HDD/SSD.
2. Locate the drive mounting position in the case.
3. Attach the HDD/SSD using screws.

Note: If you install a 2.5 inch HDD/SSD, you will not be able to install a graphics card.

J. Installing the Liquid Cooler

1. Place the cooler block or fan onto the motherboard/CPU area as pictured.
2. Secure the block or fan using the provided four screws.

Note: If you install a liquid cooler, you may not be able to install a graphics card, depending on the cooler size.

K. Complete Installation

1. Install the ATX Power Supply into its designated bay.
2. Carefully slide the motherboard tray back into the chassis.
3. Ensure the I/O shield is properly seated.
4. Secure the side panels of the case.