RU-01 Frame

(2022-07 version)

Quick Start Guide

Leading solution provider of IP-based video transmission

Packing List
Interface description
Power components installation and removal
Card installation and removal

Before using this product, it is recommended that you read the guide carefully. To ensure your personal safety and avoid physical or electrical damage to the device, please strictly follow the instructions of this guide to install and use it under the guidance of professionals. Incorrect electrical connections or physical installation may cause permanent damage to the device and even threaten personal safety.

1 Packing List

Illustration shows a front view of the RU-01 Frame and a document icon.

(1) Device ×1
(2) Quick Start Guide ×1

2 Interface description

Diagram shows the front and rear panels of the RU-01 Frame. The front panel has slots and indicators. The rear panel shows power inputs labeled AC 100-230V.

Key interfaces and indicators:

1. Power light
2. Working indicators
3. Power card slot
4. Card slot

3 LED light

PWR1 and PWR2 respectively correspond to two power status indicators, and four card indicators display four card working states.

Name	Status	Description
PWR1/PWR2 power light	OFF	No power supplied or device failure
PWR1/PWR2 power light	Red light always on	Working
Card working light	OFF	Not enabled, not insert the card or the card works abnormally
Card working light	Green light always on	The card is working

4 Power components

Power specifications: 35w power module components

Image shows a 35W power module component with an IEC C14 power input connector and an ON/OFF switch. It is labeled "AC 100~230V" and "USE ONLY WITH 250V FUSE".

5 Power components installation and removal

Align the power components with the card slots and push in parallel, then tighten the double-sided screws. Reverse the process for removal.

Diagram illustrates the installation of a power component. Step 1: Align and push the power component in parallel into the slot. Step 2: Tighten the left and right screws. Green arrows indicate the direction of insertion.

Note: The two power components work uninterrupted at the same time. When one of the components is powered off or damaged, the device will not be powered off. The other one will replace it quickly.

6 Card installation and removal

Align the card assembly with the card slots and push in parallel, then tighten the double-sided screws. Reverse the process for removal.

Diagram illustrates the installation of interface cards. Top illustration: Step 1: Align and push the encoding card in parallel into the slot. Step 2: Tighten the left and right screws. Green arrows indicate insertion direction. Bottom illustration: Step 1: Align and push the decoding card in parallel into the slot. Step 2: Tighten the left and right screws. Green arrows indicate insertion direction.

	KILOVIEW MG300 v2 Media Gateway Quick Start Guide A quick start guide for the KILOVIEW MG300 v2 Media Gateway, covering packing list, device interfaces, connection, login, usage, firmware upgrades, and factory reset.
	Kiloview MG300 Media Gateway Quick Start Guide A comprehensive quick start guide for the Kiloview MG300 Media Gateway, detailing its features, setup, operation, and troubleshooting. Learn how to connect, configure, and utilize the MG300 for IP-based video transmission.
	Kiloview: Professional Video Transmission Management Solutions Kiloview Electronics offers a comprehensive range of video transmission and management solutions, including NDI video encoders, 4G-LTE bonding encoders, 4K UHD video decoders, video converters, and media gateways for broadcast, education, medical, and other industries.
	Kiloview M2 Quick Start Guide: HDMI + VGA Dual Port Video Encoder A concise guide to setting up and using the Kiloview M2, an HDMI + VGA dual-port video encoder for live streaming and video transmission.
	Kilolink Bonding Platform User Manual User manual for the Kilolink Bonding Platform P1/P2 Series, detailing setup, connection, and management of the device for professional video encoding and multi-link bonding transmission.
	KILOVIEW D350/D260 Multi-Channel Video Decoder Quick Start Guide This guide provides instructions for setting up and using the KILOVIEW D350/D260 Multi-Channel Video Decoder, including packing list, device interfaces, LED indicators, application, OLED screen and touch button operations, web page login, decoding and output, firmware upgrading, and factory settings.
	KILOVIEW N3 3G-SDI/NDI Bi-Directional Converter User Manual User manual for the KILOVIEW N3, a 3G-SDI to NDI bi-directional converter. This guide covers product features, installation, network configuration, NDI encoding and decoding, PTZ control, and system settings for professional video production.
	KILOVIEW P Series 4G Video Encoder User Manual User manual for the KILOVIEW P Series 4G Video Encoder, detailing its features for mobile video broadcasting, including 4G bonding, high-definition streaming, and various configuration options.