Regulatory Compliance - Welcome to MERCUSYSUKCA - Welcome to MERCUSYS
Installation Guide for MERCUSYS models including: MS106LP 6-Port 10-100Mbps Desktop Switch, MS106LP, 6-Port 10-100Mbps Desktop Switch, Desktop Switch, Switch
Download for MS106LP - Welcome to MERCUSYS
File Info : application/pdf, 3 Pages, 1.51MB
DocumentDocumentQuick Installation Guide
MS106LP
LED Explanation
Power
Link/Act Status
On: The power is on
On: Link present but no activity
Off: The power is off
Flashing: Transmitting or receiving data
PoE Status
Off: No link
On: The port is providing PoE power
Off: The port is not providing PoE power
For technical support, replacement services, user guides, and other information, please visit https://www.mercusyscom/support/.
© 2023 MERCUSYS 7107500255 REV1.0.0
Switch Explanation
Recovery
Off: The PoE Auto Recovery function is disabled. On: The switch will constantly detect the working status of a PoE powered device (PD). When the switch finds that the PD works abnormally, the switch will reboot it.
Isolation
Off: Ports can transmit data with each other. On: Ports 1-4 cannot transmit data with each other. They can transmit data only with the uplink ports (ports 5-6).
Extend
Off: Ports run at100/10 Mbps and support PoE power supply up to 100m away. On: Ports run at 10 Mbps and support PoE power supply up to 250m away.
Connection
Power Adapter
Ethernet Ports (1-6)
PoE Ports (1-4)
Powered Device (PD)
IP Camera
AP
IP Phone
Internet
PC
Notes: 1. PoE ports can also connect to non-PoE devices, but only transmit data. 2. Non-PoE ports (ports 5-6) are recommended to connect to uplink devices like routers. 3. Ports 1-2 have higher priority than other ports in transmitting data if network
congestion occurs. It is recommended to connect key network devices (network cameras, APs, etc.) to ports 1-2.
Specifications
General Specifications
Standard
IEEE 802.3i, IEEE 802.3u, IEEE 802.3x
Protocol
CSMA/CD. 802.3af/at PD supported
Interface
6 10/100 Mbps RJ45 Ports Auto-Negotiation/Auto MDI/MDIX PoE Ports: Port 14
10BASE-T:2-pair UTP/STP (100m) of Cat. 3 or above Network Media (Cable) 100BASE-TX:2-pair UTP/STP (100m) of Cat. 5 or above
1000BASE-T:4-pair UTP/STP (100m) of Cat. 5e or above
Switching Capacity 1.2 Gbps
MAC Address Table 2K
Forwarding Method Store-and-Forward
MAC Address Learning Automatically learning, automatically aging
Power Supply
External Power Adapter Input: 100-240 VAC, 50/60 Hz
Output:
53.5 VDC/0.81 A
PoE Budget
40 W (up to 30 W for each PoE port)
Environmental and Physical Specifications
Certification Operating Temperature Storage Temperature Operating Humidity Storage Humidity
CE, RoHS 0°C to 40°C (32°F to 104°F) -40°C to 70°C (-40°F to 158°F) 10% to 90% non-condensing 5% to 90% non-condensing
Frequently Asked Questions (FAQ)
Q1. Why is the Power LED not lit?
The Power LED should be lit when the power system is working normally. If the Power LED is not lit, please check as follows: A1: Make sure the AC power cord/power adapter is connected the switch with power source properly. A2: Make sure the voltage of the power supply meets the requirements of the input
voltage of the switch. A3: Make sure the power source is on.
Q2. Why is the Link/Act LED not lit when a device is connected to the corresponding port?
It is recommended that you check the following items: A1: Make sure that the cable connectors are firmly plugged into the switch and the device. A2: Make sure the connected device is turned on and working well. A3: The cable must be less than 100 meters long (328 feet). If Extend Mode is enabled,
it should be less than 250 meters (820 feet).
Q3. Why are PoE ports not supplying power for PoE devices?
When the total power consumption of connected PoE devices exceeds the maximum, the PoE port with a smaller port number has a higher priority. The system will cut off power to the ports with larger port numbers to ensure supplying to other ports. For example, if port 1, 2 and 4 are consuming 10 W respectively, and an additional PoE device with 15 W is inserted to port 3, the system will cut off the power of port 4 to compensate for the overload.
Q4. What should I notice before using the PoE Auto Recovery feature?
A1: Before upgrading a connected PoE powered device (PD), disable PoE Auto Recovery to avoid the PD's damage.
A2: When a PD does not send data packets to the switch for a long period in certain scenarios (e.g. an IPC in sleep mode), disable PoE Auto Recovery to avoid the PD repeatedly rebooting.
EU declaration of conformity Mercusys hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/30/EU, 2014/35/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863. The original EU declaration of conformity may be found at https://www.mercusys.com/en/ce/
UK declaration of conformity Mercusys hereby declares that the device is in compliance with the essential requirements and other relevant provisions of the Electromagnetic Compatibility Regulations 2016 and Electrical Equipment (Safety) Regulations 2016. The original UK declaration of conformity may be found at https://www.mercusys.com/support/ukca/
Safety Information
Keep the device away from water, fire, humidity or hot environments. Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us. Place the device with its bottom surface downward. Do not use damaged charger or USB cable to charge the device. Do not use any other chargers than those recommended. Adapter shall be installed near the equipment and shall be easily accessible.
CE Mark Warning This is a class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
, . The POE output cannot be used to charge lithium batteries or devices with lithium batteries.
Explanation of the symbols on the product label Note: The product label can be found at the bottom of the product (and its .I.T.E power supply).
For indoor use only
Direct current
Alternating current
RECYCLING This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment. User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment.
BSMI Notice
Energy efficiency marking (level VI) Polarity of d.c. power connector Class II equipment Caution Operator's manual
nit
PCB
Lead (Pb)
-
Mercury Cadmium
(Hg)
(Cd)
Hexavalent chromium
Cr+6
Polybrominated Polybrominated
biphenyls diphenyl ethers
(PBB)
(PBDE)
1. 0.1 wt %0.01 wt % Note 1"Exceeding 0.1 wt %"and"exceeding 0.01 wt %"indicate that the percentage content of the restricted substance exceeds the reference percentage value of presence condition. 2. Note 2""indicates that the percentage content of the restricted substance does not exceed the percentage of reference value of presence. 3. Note 3The""indicates that the restricted substance corresponds to the exemption.
Wall Mounting Specifications
Model
Screw Standard of Minimum Length Screw-Head-to-Wall Wall-Mounting-Holes
ANSI B1.1
of Screw
Minimum Distance
Distance
MS105GP 4#, (5#), 6#, 8#
7mm
1.5mm
39mm
MS106LP MS108GP
4#, (5#), 6#, 8# 4#, (5#), 6#
7mm 7mm
1.5mm 1.5mm
39mm 105mm
MS110P
4#, (5#), 6#
7mm
1.5mm
105mm