LiftMaster CAPXM Smart Video Intercom M

Wiring Diagram

Provides a visual representation of the CAPXM system connections. Key components include the Faceplate/Screen, Speaker, Microphone, Touch Panel, Postal Lock Switch, Power Supply, USB Camera, and Door Board. It details connections for optional external Wi-Fi antennas and MyQ® Cable Extension Kits, as well as Ethernet connections and Wiegand inputs/outputs.

Caution: Information is for suggested use only. Not responsible for conflicts with local building codes. Always check local codes before installation.

Repair Parts

Accessories

* KPR2000 is not UL listed to UL 294. It cannot be used as primary means of granting or denying access but only for supplemental use. ** Available in 10 and 100 packs, replace X with 10 or 100.

Note: A current list of compatible readers and keypads is maintained at LiftMaster.com. Contact LiftMaster Technical Support for compatibility if a model is not listed.

Configuration Sheet

This section provides a template to record device information and configuration settings for the CAPXM, including Door 1 and Door 2 inputs and outputs (Wiegand, REX, Primary Relay, Auxiliary Relay) and status (EOL).

Legal Disclaimers

Canada-Underwriters Laboratories Compliance: The CAPXM must be installed per Part 1 of the Canadian Electrical Code.

Documentation Disclaimer and Restrictions: Information is subject to change without notice. LiftMaster is not responsible for conflicts between the diagram and local building codes. The document is the exclusive property of LiftMaster and protected by copyright laws. Visit LiftMaster.com for the most up-to-date information.

UL 294 Access Control Unit Endurance: Level 3, Line security: Level 1, Destructive Attack: Level 1, Power Standby: Level 1.

FCC and Industry Canada Compliance: The device complies with Part 15 of FCC rules and Innovation, Science and Economic Development Canada license-exempt RSSs. Operation is subject to two conditions: no harmful interference, and acceptance of received interference. Modifications not approved by the responsible party may void user authority. A minimum 20 cm (8 in.) distance must be maintained between the device and users/bystanders. The equipment generates, uses, and can radiate radio frequency energy, and may cause interference if not installed per instructions.

ADA Compliance: When mounting at a pedestrian entrance, the top of the CAPXM screen should not be higher than 54 inches from the ground.

Local Jurisdiction Requirements: Refer to local jurisdiction for specific requirements, such as physical signage.

California Proposition 65 Warning: This product may expose users to chemicals, including lead, known to the State of California to cause cancer or reproductive harm. Visit www.P65Warnings.ca.gov for more information.

Warranty

LiftMaster warrants the product against defects in materials and workmanship for two years from the date of purchase. Proper operation depends on compliance with installation, operation, maintenance, and testing instructions; failure to comply voids the warranty. Contact LiftMaster at 1-800-528-2806 for warranty service. This limited warranty is in lieu of all other warranties and does not cover non-defect damage, improper installation, misuse, unauthorized repairs, or labor charges for reinstallation. LiftMaster is not liable for consequential, incidental, or special damages. State laws may vary regarding limitations.

Installation Manual (French Sections Summarized in English)

The following sections provide detailed installation instructions in French, summarized here in English:

• Introduction: Covers CAPXM overview, logic board, door board, box contents, tools, dimensions, system specs, wiring specs, and internet requirements.
• Pre-Installation: Details the creation of a myQ® Business™ account, including steps for activation and setup via the LiftMaster customer service or online portal.
• Installation: Provides step-by-step guidance for removing knockouts, mounting the CAPXM unit (surface or post mount), grounding the system, and connecting power. It includes important cautions regarding moisture and proper electrical connections.
• Network: Explains how to connect the CAPXM to the internet via wired Ethernet or Wi-Fi®, including network compatibility considerations and setup steps. It also covers validating network settings.
• Access Control: Details how to configure access for barriers (wired and wireless) and doors. This includes connecting readers, keypads, door strikes, and exit devices. It specifies wiring requirements, relay functions, and troubleshooting for wireless communication with barrier actuators.

Key French Sections and their English Summary:

• Sécurité (Safety): Discusses safety symbols, warnings for mechanical and electrical hazards, and precautions to prevent serious injury or death, including disconnecting power and consulting local codes.
• Présentation du CAPXM (CAPXM Overview): Describes the Smart Video Intercom M as a cloud-based access control solution with an integrated video camera. It illustrates the front and rear components.
• Présentation de la carte logique (Logic Board Overview): Details the components on the logic board, including ports for Wi-Fi antenna, postal lock, USB, Ethernet, and diagnostic switches/LEDs.
• Présentation de la carte de la porte (Door Board Overview): Explains the door board's input/output functions for controlling up to two access points, including relay outputs, Wiegand inputs, and supervised inputs for door sensors.
• Contenu de la boîte (Box Contents): Lists items included in the package, such as the manual, power supply, and various kits.
• Outils nécessaires (Tools Required): Lists essential tools for installation, such as screwdrivers, pliers, and a multimeter.
• Dimensions: Provides front, side, rear, and bottom views with measurements in centimeters and inches.
• Caractéristiques techniques (Technical Specifications): Details CAPXM capacity, power requirements, operating temperatures, enclosure material, input/output specifications, compatibility, Wi-Fi/wireless range, and camera resolution.
• Caractéristiques techniques du câblage (Wiring Technical Specifications): Offers a table specifying wire gauge, type, and maximum distance for various connections (power, LAN, ground, door strike, lock, exit request, supervised inputs, Wiegand readers). It emphasizes using separate conduits for power and control wiring and adhering to NEC codes.
• Exigences internet (Internet Requirements): Outlines requirements for router compatibility, minimum upload/download speeds (5 Mb/s), supported Wi-Fi protocols (802.11b/g/n), security compatibility (WPA3/WPA2), and signal strength considerations.
• Création d'un compte myQ® Business™ (Creating a myQ® Business™ Account): Guides users through setting up a myQ® Business™ account, contacting customer service, and configuring the installation.
• Enlever les alvéoles défonçables (Removing Knockouts): Provides instructions on safely removing conduit knockouts from the CAPXM housing using a punch and hammer, with warnings against using excessive force.
• Monter le CAPXM (Mounting the CAPXM): Details how to securely mount the CAPXM unit to a surface or post, emphasizing the use of stainless steel hardware and ensuring proper clearance for cover opening and ADA compliance.
• Installation de la masse (Grounding Installation): Explains the importance of proper grounding for surge protection, detailing how to connect the ground wire to the CAPXM and a suitable ground source, with warnings about transient currents.
• Connecter l'alimentation (Connecting Power): Instructs on connecting the CAPXM to a dedicated 120V AC power source, specifying wire gauges, maximum distances, and the need for a dedicated 10A circuit breaker. It also details connecting the power input to the logic board and includes warnings about using only the provided power supply and avoiding surge damage.
• Se connecter à internet (Connecting to the Internet): Describes wired and Wi-Fi connection methods, including selecting network settings, entering passwords, and validating the connection. It also provides guidance on Wi-Fi signal strength and network compatibility.
• Accès à la barrière (câblé) (Barrier Access (Wired)): Illustrates the wiring for connecting barrier actuators, keypads, readers, and exit devices to the door board. It specifies relay functions and includes warnings about high-voltage wiring.
• Accès à la barrière (sans fil) (Barrier Access (Wireless)): Explains the process of wirelessly pairing the CAPXM with LiftMaster UL325 barrier actuators, including entering programming mode, selecting relays, and using the LEARN button on the actuator.
• Accès à la porte (Door Access): Provides wiring diagrams for connecting door sensors, exit buttons, door strikes, and electromagnetic locks to the CAPXM door board. It details supervised and non-supervised door sensor configurations and the use of surge protection devices.

External Links:

• LiftMaster.com
• support.partner.liftmaster.com/s/community-access-support
• www.P65Warnings.ca.gov