Installation Guide for AXXESS models including: AXBUCS-NI246V, 120AXSWC, ASWC-1, AXBUCS-NI246V Steering Wheel Control Harness, AXBUCS-NI246V, Steering Wheel Control Harness, Wheel Control Harness, Control Harness, Harness
Axxess AXBUCS-NI246V Steering Wheel Control Harness Install the Axxess AXSWC steering wheel control adapter without splicing in select 2017-18 Nissan vehicles (requires item #120AXSWC, sold separately) at Crutchfield
File Info : application/pdf, 4 Pages, 310.47KB
DocumentDocumentInstallation Instructions for AXBUCS-NI246V AXBUCS-NI246V Nissan (with NAV) 2011-Up INTERFACE FEATURES · Prewired AXSWC harness (AXSWC sold separately) · Retains the factory AUXIN jack · Retains the factory backup camera to an aftermarket radio* · Includes the AXCSD6V 12volt to 6volt converter * Will not work with models equipped with an "All Around Camera" system INTERFACE COMPONENTS · AXBUCSNI246V harness · AXCSD6V 12volt to 6volt converter APPLICATIONS NISSAN Frontier2013Up* Rogue (w/ Bose) Titan20132015* Altima 2013Up Juke 20112014* 20122013* Versa 2013Up* Cube NV 2012Up* Rogue 2011* Xterra 20112014* NV200 2012Up* Sentra 2011Up* 20132015* * For use when retaining the OE backup camera only TOOLS REQUIRED · Wire cutter · Crimping tool · Solder gun · Tape · Connectors (example: butt connectors, bell caps, etc.) CAUTION! All accessories, switches, climate controls panels, and especially air bag indicator lights must be connected before cycling the ignition. Also, do not remove the factory radio with the key in the on position, or while the vehicle is running. Axxess Integrate axxessinterfaces.com · metraonline.com REV. 5/19/20 © COPYRIGHT 2020 METRA ELECTRONICS CORPORATION Installation Instructions for AXBUCS-NI246V Connections to be made · Connect the Black wire with a ring terminal to chassis ground. · Connect the Black wire of the AXCSD6V wire to chassis ground. · Connect the Red wire labeled "Camera Power 6V" to the Blue/Red wire of the AXCSD6V. · Connect the Green/Purple wire to the reverse wire of the aftermarket radio, and also to the Blue/White wire of the AXCSD6V. · For all models except the Cube / Rogue, if retaining the factory AUXIN jack, connect the Red & White RCA jacks to the AUX input. · Connect the Yellow RCA jack to the rear camera input of the aftermarket radio. 12-pin pre-wired AXSWC harness: This harness is to be used along with the optional AXSWC (not included) to retain steering wheel audio controls. Please refer to the AXSWC instructions for radio connections and programming. Note: Disregard the harness that comes with the AXSWC. · Connect the unlabeled Red wire to the accessory wire. KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow. Metra recommends MECP certified technicians Axxess Integrate axxessinterfaces.com · metraonline.com REV. 5/19/20 © COPYRIGHT 2020 METRA ELECTRONICS CORPORATION Instrucciones de instalación para AXBUCS-NI246V AXBUCS-NI246V Nissan (con NAV) 2011 y Mas CARACTERÍSTICAS DE LA INTERFASE · Arnés AXSWC precableado (el AXSWC se vende por separado) · Retiene el conector de de la fábrica AUXIN · Retiene la cámara de reversa de fábrica de mercado secundario* · Incluye el AXCSD6V 12 voltios al convertidor de 6 voltios * No funciona con los modelos equipados con un sistema de "todo alrededor de la cámara" COMPONENTES DE LA INTERFASE · Arnés AXBUCSNI246V · AXCSD6V 12 voltios al convertidor de 6 voltios APPLICATIONS NISSAN Juke20112014* Rogue (con Bose) Versa Altima 2013ymas NV 2012 y Mas* 20122013* 2013 y mas* Cube 20112014* NV200 Rogue 2011* Xterra Frontier 2012 y Mas* Sentra2011yMas* 20132015* 2013 y Mas* Titan20132015* * Para usar cuando la cámara de OE se va a retener HERRAMIENTAS REQUERIDAS · Cortacables · Ponchadora · Pistola soldadora · Cinta · Conectores (ejemplo: conectores de extremo, de campana, etc.) ¡PRECAUCIÓN! Todos los accesorios, interruptores, paneles de controles de clima y especialmente las luces del indicador de las bolsas de aire deben estar conectados antes ciclar la ignición. Además, no quite el radio de fábrica con la llave en la posición o de encendido ni con el vehículo funcionando. Axxess Integrate axxessinterfaces.com · metraonline.com REV. 5/19/20 © COPYRIGHT 2020 METRA ELECTRONICS CORPORATION Instrucciones de instalación para AXBUCS-NI246V Conexiones que se deben hacer · Conecte el cable negro con una terminal de aro al tierra del chasís. · Conecte el cable negro del AXCSD6V a tierra del chasís. · Conecte el cable rojo marcado con "Cámara de alimentación de 6V" a el cable azul/rojo del AXCSD6V. · Conecte el cable verde/púrpura al cable de reversa del radio de mercado secundario y también para el cable azul/blanco de la AXCSD6V. · Para todos los modelos excepto el Cubo / Rogue, si retener el enchufe AUX IN de fábrica, conecte los conectores RCA rojo y blanco al entrada AUX. · Conecte el conector RCA amarillo RCA en la entrada de la cámara de reversa del radio de mercado secundario. Arnés AXSWC precableado de 12 pins: Este arnés se debe usar junto con el AXSWC opcional (no incluido) para retener los controles de audio en el volante. Consulte las instrucciones de AXSWC para las conexiones del radio y la programación. Nota: Ignore el arnés que viene con el AXSWC. · Conectar el cable rojo marcado con el cable accesorio. EL CONOCIMIENTO ES PODER ® Mejore sus habilidades de instalación y fabricación inscribiéndose en la escuela de dispositivos electrónicos móviles más reconocida y respetada de nuestra industria. Regístrese en www.installerinstitute.com o llame al 8003546782 para obtener más información y avance hacia un futuro mejor. Metra recomienda técnicos con certificación del Programa de Certificación en Electrónica Móvil (Mobile Electronics Certification Program, MECP). Axxess Integrate axxessinterfaces.com · metraonline.com REV. 5/19/20 © COPYRIGHT 2020 METRA ELECTRONICS CORPORATION