Installation & Assembly
Product Dimensions: Table: 23.62"W x 23.62"D x 29.13"H, Chair: 22.44"W x 23.62"D x 33.07"H
Weight Capacity: Table: 176 lbs, Single Seat: 352 lbs
Notice
- Please ensure all parts are present and in good condition before assembly. Refer to the part and hardware lists for guidance.
- Assemble this item on a soft surface to prevent scratching the finish during assembly.
- This item may require periodic tightening.
- If you encounter difficulties, our Customer Care team is available to assist.
Preparation
- Before starting assembly, verify all parts against the part and hardware contents lists.
- Do not attempt to assemble if any part is missing or damaged.
- Estimated Assembly Time: 60 minutes.
- Tools Required for Assembly (included): Allen Key.
- For assistance, please email customersupport@safavieh.com.
Care and Maintenance
Store outdoor furniture indoors or cover it thoroughly when not in use. Dust regularly with a small brush or vacuum. Clean spills immediately before they harden or stain using a slightly damp sponge.
Part List and Hardware List
| Piece | Description | Picture Description | Quantity |
|---|---|---|---|
| A | Right Leg Chair | [Chair Leg] | 2X |
| B | Left Leg Chair | [Chair Leg] | 2X |
| C | Back Chair | [Chair Back] | 2X |
| D | Seat Chair | [Chair Seat] | 2X |
| E | Top Table | [Table Top] | 1X |
| F | Front Table | [Table Frame Part] | 2X |
| G | Leg Table | [Table Leg] | 2X |
| H | Table Glass | [Glass Top] | 1X |
| CSH | Seat Cushion | [Cushion] | 2X |
| HW1 | Allen Bolt: M6 x 0.5 x 80 mm | [Bolt M6x80mm] | 4X |
| HW2 | Allen Bolt: M6 x 0.5 x 40 mm | [Bolt M6x40mm] | 12X |
| HW3 | Allen Bolt: M6 x 0.5 x 20 mm | [Bolt M6x20mm] | 12X |
| HW4 | Allen Bolt: M6 x 0.5 x 15 mm | [Bolt M6x15mm] | 4X |
| HW5 | Flat Washer: M6 x 1 mm | [Flat Washer M6x1mm] | 32X |
| HW6 | Washer: M6 x 5 mm | [Washer M6x5mm] | 4X |
| HW7 | Allen Key | [Allen Wrench] | 1 |
Assembly Instructions
Warning: Do not stand on the table or chair. Do not over-torque bolts.
Table Assembly
Step 1: Connect two Leg Tables (G) to the Top Table (E). Use Bolt (HW4) and Flat Washer (HW5) with the Allen Key (HW7). Tighten to 50%.
Step 2: Connect the assembly from Step 1 to the Front Table (F). Use Bolt (HW3) and Flat Washer (HW5) with the Allen Key (HW7). Tighten to 50%.
Step 3: Connect another Front Table (F) part to the assembly from Step 2. Use Bolt (HW3) and Flat Washer (HW5) with the Allen Key (HW7). Tighten to 50%.
Step 4: Place the table upright. Ensure all legs are level. Firmly tighten all bolts with the Allen Key (HW7). Place the Glass (H) on top to complete the table assembly.
Chair Assembly
Step 5: Connect the Back Chair (C) to the Seat Chair (D). Use Bolts (HW2, HW3) and Flat Washer (HW5) with the Allen Key (HW7). Tighten to 50%.
Step 6: Connect the assembly from Step 5 to the Right Leg Chair (A). Use Bolts (HW1, HW2) and Flat Washer (HW5) with the Allen Key (HW7). Tighten to 50%.
Step 7: Connect the assembly from Step 6 to the Left Leg Chair (B). Use Bolts (HW1, HW2) and Flat Washer (HW5) with the Allen Key (HW7). Tighten to 50%.
Step 8: Place the chair upright. Ensure all legs are level. Firmly tighten all bolts with the Allen Key (HW7). Place the Seat Cushion (CSH) onto the chair. The chair is now ready for use.
