User Guide for Sunricher models including: SRP-1009N-12CCT100-700 12W RF NFC Enabled LED Driver Constant Current, SRP-1009N-12CCT100-700, 12W RF NFC Enabled LED Driver Constant Current, Enabled LED Driver Constant Current, LED Driver Constant Current, Driver Constant Current, Constant Current
File Info : application/pdf, 5 Pages, 1.23MB
DocumentDocument12W RF NFC Enabled LED Driver(Constant Current) IS ------ THOMAS SAMUEL THOMAS SAMUEL R-xxxxxxxx Important: Read All Instructions Prior to Installation Function introduction AC Push input PUSH L PUSH N PUSH DIM L N CWWW- RF Dimmable Driver L LED Output INPUT N AC/DC power input Product Data LED Channel 2 DC Voltage 6-42V, Max. 50V Output Input Current 100-700mA via NFC tool; Min.current gear lower to 0.1mA, default 300mA Current Accuracy ±3%( ±1%@Certain full load) @ full load Rated Power Max. 12W Voltage Range Absolute Voltage Range Frequency Range Power Factor (Typ.) Total Harmonic Distortion Efficiency (Typ.) AC Current (Typ.) Inrush Current (Typ.) Leakage Current Anti Surge Dimming Interface 220-240VAC/220-240VDC 196-264VAC/196-264VDC 0/50/60Hz > 0.95 @ 230VAC Full load THD 15% (@ full load / 230VAC) 75% @ 230VAC full load 0.1A Max. Max. 3.96A at 230VAC; 80s duration < 5mA /230VAC L-N:2KV RF (Sub-G) Control Dimming Range Dimming Method 0.01%-100%@ Max current Amplitude/CCR dimming Dimming Curve Linear/ Logarithmic optional Short Circuit Yes, remove the fault conditions and re-power the device. Protection Over Current Yes, remove the fault conditions and re-power the device. Over Temperature Yes, remove the fault conditions and re-power the device. Working Temp. -25 ~ +45 Max. Case Temp. Environment Working Humidity Tc=85 10% ~ 95% RH non-condensing Storage Temp. & Humidity -40 ~ +80, 10% ~ 95% RH Safety Standards EN61347-1, EN61347-2-13, GB/T 19510.1-2023, GB/T 19510.213-2023 Safety & EMC Withstand Voltage I/P-O/P: 3.75KVAC Isolation Resistance I/P-O/P: 100M Ohms / 500VDC / 25 / 70% RH EMC Emission EN55015, EN61000-3-2, EN61000-3-3, GB 17625.1-2022, GB/T 17743-2021 EMC Immunity EN61547, EN61000-4-2,3,4,5,6,8,11 Others MTBF Dimension Warranty 191350H, MIL-HDBK-217F @ 230VAC full load and 25 ambient temperature 135x35x20mm (L*W*H) 5 Years · Dimmable LED driver. Max. output power 15W · 100-700mA current selectable via NFC program tool. Min.current gear lower to 0.1mA · Dimming curves/Target current/Power-on behavior settings via NFC program tool · Class power supply, full isolated plastic case · High power factor and efficiency · Radio Frequency : Default 869.5/916.5(1009 Version) ,Available 868/434mhz(2504 Version) · To switch and dim Tunable White LED lighting fixtures · Amplitude/CCR dimming, smooth and deep dimming · Compatible with a variety of RF remotes · IP20 rating, suitable for indoor LED lighting applications · 5 years warranty Safety & Warnings · DO NOT install with power applied to the device. · DO NOT expose the device to moisture. Pairing devices with RF remote 1.Do wiring according to connection diagram. 2.Pair RF Driver with RF remote: please refer to the instruction of the remote that you would like to pair with. With NFC Programming devices Note 1) Do wiring according to the wiring diagram. 2) Recommend setting parameters without power-on the RF devices . 2) Please make sure your mobile phone has NFC function and enable it . Working with "SR NFC Tool" APP Step 1: Download the APP (searching "SR NFC Tool" from App Store and Google Play) . Then open the APP . Download "SR NFC Tool " Tap "+" to add RF devices Note: 1. Please Make sure that you have enabled NFC function with your mobile phone/ tablet . 2. Please Make sure that the "NFC position" is matched. 3. Please do not power on the device before setting. 4. If you can't download "SR NFC Tool". Please contact with us. Step 2: Add device, and name it as you wish. Step 3: Unlock device, enter parameters configuring page. Locked Unlock it Note: 1. You have to unlock the device then do some settings 2. Only when the corresponding function is selected, the function interface will be displayed. Step 4: Few parameter interface, you can choose the setting based on your requirements. 1) We bring well-praised "DALI" dimming curve to this product, to ensure you have the smooth dimming performance in RF NFC drivers. 2) Besides that, we have the other dimming curves available with intutive graphs, enables you shall find your ideal one. 1) Off: Always Off after power on. 2) On: Always On after power on 3) Latest: Restore to last light level after power on 1) 0(No fade): Fatest transition 2) 15: Longest transition 3) 3(Default): Soft transition 1) Enable Pairing: The driver will enter the pairing mode and work with RF remote 2) Clear all paired devices Cleaning paired devices (Seldom use 3) Ignore: When you about to set other parameter please select this, otherwise the devices statues shall be re-write which is not your willing. Input the working current of the LED. Min.0.1mA per gear as a option. Which massively free the options among different luminaries specification Tips 1. NFC function doesn't require any power driver. 2. Many functions can be configured by NFC. Kindly check your desired functions. 3. All of our RF NFC drivers are in the best performance within OUR Remotes. 4.This is a 2-channel output product, so we recommend ensuring that both loads are connected and have the same loads for each channel at the same time during testing. 5. For 1 channel fixtures, please make sure you have our 1 channel drivers connected. 6: Read before you Move. Current compensation setting: Enables you achieve the best dimming performance per different current gear. But still we gave the options to customers which enable customized setting. Wiring Diagram 1. Work as Pure RF driver 1.1 With 3-wire CCT LED luminarie LN PUSH L PUSH N PUSH DIM L N CWWW- RF Dimmable Driver L INPUT Note: Available with 4-Wire CCT LED luminaries as well. 3-Wire CCT LED N N 2. Work with Pure RF driver and AC PUSH function AC PUSH SWITCH PUSH L PUSH N PUSH DIM L N CWWW- RF Dimmable Driver L 3-Wire CCT LED INPUT Note: Available with 4-Wire CCT LED luminaries as well. LN AC Push Function 1) Click the button to switch ON/OFF 2) Press and hold down the button to increase or decrease light intensity to desired level and release it, then repeat the operation to adjust light intensity to opposite direction. The dimming range is from 1% to 100%. 3) Double click the button to switch between brightness mode and color temperature mode. 4) Press and hold down the button to change color temperature under color temperature mode. Product Dimension Operating window Output voltage [V] 42 35 28 21 14 7 0 Dimming Curve ULED (max), V ULED (min), V 0,10 0,20 0,30 0,40 0,50 0,60 0,70 0,80 Output current [A] Note: Test data under 700mA gear Driver Performance 20 mm 135 mm 126.8 mm 27.8 mm 35 mm 3.2 mm 45%/ 52%/ 70%/ 85%/ 97%/ 98% Note: Test data under 700mA gear Driver Performance 45%/ 52%/ 70%/ 85%/ 97%/ 98% Note: Test data under 700mA gear Driver Performance MCB Load Quantity Module Number Ipeak Twidth Max.quantity of LED Driver per MCB B10 B13 B16 B20 B25 C10 C13 C16 C20 C25 D10 D13 D16 D20 D25 SRP-1009N-12CC100-700 SRP-2504N-12CC100-700 3.96A 90s 37 49 60 75 94 63 81 100 125 156 80 104 128 160 200 SRP-1009N-12CCT100-700 SRP-2504N-12CCT100-700 3.96A 90s 37 49 60 75 94 63 81 100 125 156 80 104 128 160 200 I (A) Ipeak ½ Ipeak t T (ms) Note: 1.Those MCB parameters are based on ABB S200 series circuit breakers. 2.For different brands and models of miniature circuit breakers, the quantity of drivers will have difference. 3.Please do not exceed the above-mentioned quantity during on-site installation, and the specific load quantity shall be subject to on-site installation. 4.When the installation environment temperature of MCBs exceeds 30°C or when multiple MCBs are installed side by side, the number of mounted drives will be reduced, which requires recalculation. 5.Type C MCB's are strongly recommended to use with LED lighting 7%/ 10%/ 12%/ 15%/ 20%/ 22%/ 30%/ 37%/ 49%/ 61%/ 73%/ 85%/ 97% Note: Test data under 700mA gear Expected Lifetime Module Number Output current Ta 30 °C 40 °C 45 °C SRP-1009N-12CC100-700 SRP-2504N-12CC100-700 100 700 mA Tc 50 °C 60 °C 65 °C SRP-1009N-12CCT100-700 SRP-2504N-12CCT100-700 100 700 mA Lifetime > 100,000 h > 100,000 h > 100,000 h 85 °C > 40,000 h The LED driver is designed for a lifetime stated above under reference conditions. The relation of tc to ta temperature depends also on the luminaire design. Date 2024-7-26 Version V1.0 Update content Initial Version Update by Romeo