Instruction Manual for AIE models including: AIE-210C, AIE-210C Cutter Impulse Hand Sealer, Cutter Impulse Hand Sealer, Impulse Hand Sealer, Hand Sealer, Sealer
CUTTER IMPULSE HAND SEALER INSTRUCTION MANUAL
17 mai 2025 — INSTRUCTION MANUAL. (AIE-200C, AIE-210C, AIE-. 300C ONLY). Page 2. 2 | P a g e. OVERVIEW. This impulse sealer serves the crucial purpose of securing a hermetic ...
CUTTER IMPULSE HAND SEALER AIE-210C INSTRUCTION MANUAL (AIE-200C, AIE-210C, AIE300C ONLY) 1|Page OVERVIEW This impulse sealer serves the crucial purpose of securing a hermetic seal, providing effective waterproof and airtight packaging. Additionally, it will cut away excess material ¼" from the seal. KEY CHARACTERISTICS · Compact Design · Strong Watertight Seal · Fast Operating · Power Saving · Precision Electronic Circuit · Industrial durability OPERATING INSTRUCTIONS 1. Plug the cord into a properly grounded electrical outlet. The machine will operate only when the sealing arm is completely depressed. 2. Adjust the sealing timer knob to a suitable time based on your sealing bag thickness and material on a scale of 1-8 (it is recommended to use the smallest timer number possible while still sealing the bag). 3. Insert the bag between the jaws and press the handle down. Maintain pressure while the light is active. Continue to maintain pressure after the light is off for approximately the same time as the heat cycle for the congealing phase. A longer congealing phase will provide a more secure and consistent seal. a. If the bag sticks to the silicon rubber, the bag needs a longer congealing phase. b. The timer knob does not need to be adjusted once it is calibrated. 4. Check the seal. If the seal isn't tight, raise the timer knob to a higher setting and repeat step 3. 5. Blade Cutter Option: Slide the red tab on the top of the sealer arm to cut away the excess material. 6. Power is not consumed when the machine is plugged in until it is in use. NOTES · Always keep the sealing platform clean. Cleaning excess residue will improve the longevity of the heating element, PTFE cloth strips, and silicon rubber. · Do not use moisture or harsh cleaning solutions to clean the sealing surface. · Replace the torn PTFE cloth immediately. A torn cloth may cause a short circuit and will damage the element wire. Every time you replace the heating element, replace the lower and upper PTFE cloth. · Only use genuine replacement parts. · A worn silicon rubber will negatively influence the seal; change the silicon when worn, burnt, or if grooves or indents are present. 2|Page · Always unplug the cord from the electrical outlet when servicing your machine. CHANGING PARTS To replace the cutting blade: Slide the cutter toward the slot near the handle. 1. Lift the slider up and out. 2. Loosen only the screw and remove the blade with pliers. 3. Replace with a new blade, re-tighten the screw, and reinsert the holder in the slot near the handle. To replace the heat element wire: 1. Loosen the screws that will loosen the metal plate (#9). 2. Lift up or take off the upper PTFE (#11). Replace it if burned through. 3. Remove the damaged heating element wire (#12). Note: Check if the lower PTFE (#10) is burnt or damaged. Replace it if necessary. Make sure it covers the element bottom entirely. This PTFE is very important for protecting your machine by insulating the wire and separating the element wire from the metal of the machine. 4. Attach a new element wire, reattach the upper PTFE, and reattach the metal plate. PARTS DIAGRAM 3|Page PARTS LIST No. Description AIE-200C AIE-205C AIE-210C AIE-300C AIE-305C AIE-400C AIE-405C AIE-500C AIE-505C 1 HANDLE KNOB BAKELITE BAKELITE BAKELITE BAKELITE BAKELITE BAKELITE BAKELITE BAKELITE BAKELITE 2 PLATEN ARM ARM200C ARM200C ARM200C ARM300C ARM300C ARM400C ARM400C ARM500C ARM500C 3 PLATEN SPRING PLATESPC PLATESPC PLATESPC PLATESPC PLATESPC PLATESPC PLATESPC PLATESPC PLATESPC 4 PLATEN PLATEN2C PLATEN2C PLATEN2C PLATEN3C PLATEN3C PLATEN4C PLATEN4C PLATEN5C PLATEN5C 5 SILICON RUBBER SR200C SR200C SR210C SR300C SR300C SR400C SR400C SR500C SR500C 6 HINGE POLE2C POLE2C POLE2C POLE3C POLE3C POLE4C POLE4C POLE5C POLE5C 7 HINGE BRACKET HINGE2C HINGE2C HINGE2C HINGE2C HINGE2C HINGE2C HINGE2C HINGE2C HINGE2C 8 ENCLOSURE BD200C BD200C BD200C BD300C BD300C BD400C BD400C BD500C BD500C 9 METAL PLATE MPLATE2C MPLATE2C MPLATE2C MPLATE3C MPLATE3C MPLATE4C MPLATE4C MPLATE5C MPLATE5C 10 LOWER ELEMENT PTFE TFL200C TFL200C TFL210C TFL300C TFL300C TFL400C TFL400C TFL500C TFL500C 11 UPPER PTFE CLOTH TF200C TF200C TF210C TF300C TF300C TF400C TF400C TF500C TF500C 12 HEATING ELEMENT STRAIN RELIEF 13 BUSHING EF200C EF205C EF210C EF300C EF305C EF400C EF405C EF500C EF505H CORLDHOLD CORLDHOLD CORLDHOLD CORLDHOLD CORLDHOLD CORLDHOLD CORLDHOLD CORLDHOLD CORLDHOLD 14 POWER SUPPLY CORD CORD-H CORD-H CORD-H CORD-H CORD-H CORD-H CORD-H CORD-H CORD-H 15 TIMER SET TI-H3 TI-H3 TI210C TI-H3 TI-H3 TI-H3 TI-H3 TI-H3 TI-H3 16 SWITCH LEVEL LEVER2C LEVER2C LEVER2C LEVER3C LEVER3C LEVER4C LEVER4C LEVER5C LEVER5C 17 WIRE CONNECTOR BUSH-H BUSH-H BUSH-H BUSH-H BUSH-H BUSH-H BUSH-H BUSH-H BUSH-H 18 HEAT TRANSFORMER TR200C TR205C TR210C TR300C TR305C TR400C TR405C TR500C TR505C 19 MICROSWITCH SET SWITCH LEVER 20 SPRING MICRO-SET MICRO-SET MICRO-SET MICRO-SET MICRO-SET MICRO-SET MICRO-SET MICRO-SET MICRO-SET MOVESP2C MOVESP2C MOVESP2C MOVESP3C MOVESP3C MOVESP4C MOVESP4C MOVESP5C MOVESP5C 21 HEATER TERMINAL SET BOW-SET BOWSETH5 BOWSETH5 BOW-SET BOWSETH5 BOW-SET BOWSETH5 BOW-SET BOWSETH5 22 COVER PLATE RUBBER FOOT & 23 SCREW CUTTING HANDLE & 24 BLADE COVER2C FOOT-H3 BHOLDER COVER2C FOOT-H3 BHOLDER COVER2C FOOT-H3 BHOLDER COVER3C FOOT-H3 BHOLDER COVER3C FOOT-H3 BHOLDER COVER4C FOOT-H3 BHOLDER COVER4C FOOT-H3 BHOLDER COVER5C FOOT-H3 BHOLDER COVER5C FOOT-H3 BHOLDER 4|Page REPLACEMENT KITS Model AIE200C AIE205C AIE210C AIE300C AIE305C AIE400C AIE405C AIE500C AIE505C Replacement Kit Replacement Kit w/ blade K200C K205C K210C K300C K305C K400C K405C K500C K505C K200CB K205CB K210CB K300CB K305CB K400CB K405CB K500CB K505CB ELECTRICAL CONNECTION DIAGRAM SPARE PARTS ACCESSORIES HEATING ELEMENT UPPER CLOTH QUANTITY 2 2 5|Page SPECIFICATIONS Model AIE200C AIE205C AIE210C AIE300C AIE305C AIE400C AIE405C AIE500C AIE505C Voltage 110 V 110 V 110 V 110 V 110 V 110 V 110 V 110 V 110 V Watts 260 W 450 W 600 W 380 W 600W 750 W 1000 W 900 W 1200 W Max Seal Length 8" 8" 8" 12" 12" 16" 16" 20" 20" Max Seal Thickness 4 mil 6 mil 7 mil 5 mil 6 mil 6 mil 8 mil 6 mil 8 mil Seal Width 2 mm 5 mm 10 mm 2 mm 5 mm 2 mm 5 mm 2 mm 5 mm Special Order Option: These sealer models are also available in 220 Volts upon request. Weight 10 lbs. 11 lbs. 13 lbs. 12 lbs. 14 lbs. 15 lbs. 15 lbs. 18 lbs. 19 lbs. 6|PageMicrosoft Word for Microsoft 365