SUPERSOCO
User Manual for SOCO models including: CUmini, E-Scooter, CUmini E-Scooter, Scooter
Super Soco CUmini elektrische scooter
CU | Super Soco
File Info : application/pdf, 33 Pages, 3.31MB
DocumentDocumentE-Scooter User Manua Do not operate the electric vehicle until you have read the user manual carefully and understand the performance of the electric vehicle, and please keep the user manual in a safe place. USER INSTRUCTION To ensure your safety, please read this manual carefully before riding and make sure you are always following the requirements below: 1 Fully understand the information in this manual, including but not limited to the relevant instructions, precautions and warnings. 2 Fully understand the operation and contingency measures of CUmini Smart Electric Scooter. 3 Be fully aware of warning labels of CUmini Smart Electric Scooter. 4 Do not disassemble the vehicle or any parts without permission. Please contact customer service department and dealers if you need any replacement or make further purchase. 5 Please keep the user manual in a safe place. All parameters of this vehicle have been permanently set according to the national standard before leaving factory. The company is not responsible, if the original electrical or circuit has changed and caused excess, such as increase the speed. SAFETY INSTRUCTION To ensure the safety of you and others, please make sure to observe the following: 1 Don't lend your vehicle to someone who can't operate it to prevent any hurts. 2 Juveniles under 16 years old are strictly prohibited to drive electric scootor on the road. 3 Please drive in the bicycle lane and the maximum speed should not exceed 15km/h. (Keep to the right if there is no bicycle lane.) 4 Do not ride on the road after taking medications, drinking alcohol or when you feeling unwell which may affect your riding ability. 5 Observe traffic regulations and traffic signs, according to the provisions of laws and regulations to carry man and cargo. Confirm the surrounding road conditions and vechile condition any time to actively avoid danger. 1 SAFETY INSTRUCTION 6 In rainy and snowy weather, braking distance will be extended, please slow down the vehicle. Avoid travelling in bad weather such as storms and typhoons. 7 Wear safety gears, especially helmet. Wear appropriate protective clothing like boots and gloves if necessary. 8 To ensure the safety of you and others, please avoid using the high beam under good lighting conditions. The continuous use of high beam will cause visual obstacles to opposite vehicles and pedestrians and affect the safe driving. In the case of dim light, turn on the lights in time. 9 Please turn off the power immediately and remove the key after riding. Do not allow children play the vehicle to avoid unnecessary losses. 10 Perform a basic check each time before riding. 11 Please pay attention to the safe operation of the electric vehicle: a Do not park the vehicle indoors or in the hallway. b Do not charge the battery/vehicle indoors or in the hallway. The battery/vehicle should be kept away from combustible materials when charging, and the charging time should not be too long. c Please pay attention to the correct usage of the battery and warning labels.Wasted batteries should not be dismantled without authorization, and should be managed and recycled by the relevant professional departments. d Please pay attention to the safe usage and the warning labels of the charger. Make sure to use the original charger for the same model. e Please be aware of the precautions regarding water washing. 12 Check before riding, if there is an abnormality, please promptly carry out maintenance or find professionalrepair service: a Check the status of power circuit, lighting circuit, etc. b Check whether the front and rear brakes work properly. c Check whether the handlebars, front and rear wheels are stable. d Check tire pressure. e Check whether the reflectors are stained. f When adjusting handlebars or saddles, make sure not to expose the safety line marks (where applicable) 2 QUICK START 01 ACCESSORIES CHECKLIST X2 Intelligent Remote Control X1 Quick Start X2 Key X1 Wrench for Rearview Mirrors X1 Charger 3 3 QUICK START 02 INSTALL BATTERY PACK 1 Open the cushion/battery 2 Put in the battery pack. 3 Plug in the main compartment. connector. 4 Put back the cushion. 4 QUICK START 03 STARTING VEHICLE 1 Put on the helmet. 2 Get on your CUmini, retract the side stand. 3 Press "Unlock" button on the intelligent remote control. mile 4 Press the "Parking" button. 5 5 The vehicle enters READY state. 6 Gently twist the throttle to ride on the road. QUICK START 04 DOWNLOAD APP CU mini Smart Electric Scooter supports wireless communication, GPS, etc., which can connect the vehicle with your smart phone. You can manage and query your vehicle through SOCO App on your smart phone. Available on iOS and Android platforms, please check your smart phone operating system before installation. iOS platform: App requires iOS 9.0 or later. Android platform: App requires Android 4.4 or later. Download and install SOCO App by scanning the QR code in the last page of this manual. SOCO APP Since the date of purchase, you will be presented with 1 year's free data of SIM card to use SOCO APP function.Make sure to recharge it before the free period expires. For those who fail to recharge within the time limit, the operator will close the recharge interface, and the recharge function of data cannot be restored, in which case SOCO APP cannot be used normally. 6 PARAMETER TABLE Main Specifications and Performance Index for CUmini. Main Specifications Battery Main Specifications Motor Main Specifications Controller Main Specifications 7 LxWxH(mm) Wheelbase(mm) Total Weight of the Vehicle(kg) Max Speed(km/h) Full Charge Endurance(km) Energy consumption per 100km(KWh) Load(kg) Type Total Capacity(Ah) Total Voltage(V) Motor Type Rated Power(W) Rated Rotating Speed (r/min) Rated Voltage(V) Undervoltage Protection Value (V) Overcurrent Protection Value(A) Configeration1 1655×695×1083 1169 54.5 25 60 1.5 75 Lithium Battery 20 48 Permanent Magnet 350 290 48 42±1 21±1 Configeration2 1655×695×1083 1169 53.5 25 50 1.5 75 Lithium Battery 16 48 Permanent Magnet 350 290 48 42±1 21±1 CONTENTS Description of Components and Parts 9 Operation Guide 11 Riding Guide 14 Battery use Instructions 17 App Instructions 21 Maintenance 22 Common problems and Troubleshooting methods 23 8 DESCRIPTION OF COMPONENTS AND PARTS a. Schematic diagram of vehicle parts SIDE VIEW Day Light Headlight/ Turn Signal Disc Brake VIN Code 9 USB Port TOP VIEW Front Brake Lever Hook Battery Compartment Taillight FOC Vector Controller Motor Motor Code Configuration 2 Drum Rear Brake Center Stand Name Plate Disc Rear Brake Rear Brake Lever Throttle Control Right Handlebar Control Assy Seat Peddle Dashboard Left Handlebar Control Assy DESCRIPTION OF COMPONENTS AND PARTS b. Dash Overview 1 2 3 4 5 1 Speedometer/Error Codes 3 State of Charge (SoC) Display current speed of the vehicle. Display the SoC in percentage. When the error indicator illuminates, it displays error code. 5 State of Headlight Display the on/off state of headlight. 2 Total Mileage/Mileage Per Trip Display total mileage and mileage per trip. 4 Power Display Bar Display current amount of energy Error Indicator Display error with error code. Battery Error Indicator Flicker when electric quantity is 10%. 10 OPERATION GUIDE a. Left Handlebar Control Assy 4 1 1 Headlight Switch Tap to switch on/off. 2 Turn Signal Switch Turn to left, left turn signal on; Turn to right, right turn signal on, keep in middle, turn signal off. 11 2 3 3 Horn Button Press, horn on; Release, horn off. 4 One-Click Fix Turn on the power switch, then press the "One-Click Fix", you can start the self-check operation. If there is a failure such as Hall fault and handle fault, the vehicle can keep driving normally at a low speed. OPERATION GUIDE b. Right Handlebar Control Assy 1 2 1 Warning Button Press the triangle warning button as shown in the picture to turn on the emergency flasher. 2 Parking Button When the vehicle is unlocked, tap the button to enter the "READY" state, and gently turn the handle to start the vehicle;When the vehicle is stationary, tap the button to enter the locked state. 12 OPERATION GUIDE c. Intelligent Remote Control Operation CUmini is equipped with second generation SOCO Intelligent Remote Control, with a press of the button, you can lock or unlock the vehicle within effective distance. 1 Keyless Start When the vehicle is unlocked, tap the button to enter the power-on state.After the "READY" light is on, turn the handle lightly to start the vehicle.When the vehicle is powered on and stationary, tap it again to power off the vehicle. 2 Unlock Button Press "Unlock" button, the vehicle enters unlocked state. d. Open Battery Compartment Insert the key and turn it clockwise to open the battery compartment 3 Lock Button When the vehicle is in a stationary state, press "Lock" button, the vehicle enters locked state. 13 RIDING GUIDE a. Pre-ride Checklist Before operating your CUmini Smart Electric Scooter, check the following to ensure your own safety: 1 Check whether the handlebar is stable and flexible when turning. 2 Check whether the left and right handlebar controls work properly. 3 Check whether the throttle control works properly. 4 Make sure the tire pressure is within normal range. The suggested tire pressure is 175-200 kPa for the front tire, and 200- 225 kPa for the rear tire (maximum tire pressure 280Kpa). 5 Make sure that there are no cracks, damage, wear, foreign object puncture or adhesion on the tire surface. 6 Check trend depth of both tires is enough. If the tire is worn to the black shaded mark on the diagram, it needs to be replaced. 7 Check if any error warning sign illuminates on the dash when power on. 8 Check whether the battery capacity is sufficient for your trip. 9 Check whether all lights function properly. 10 Check whether horn function properly. 11 Check whether rearview mirrors are clean and adjust them to appropriate angle. 12 Check whether the handlebar and brake system function properly. If you have any questions, please contact SOCO Customer Service. 14 RIDING GUIDE b. Start the vehicle 1 Put on the helmet. 2 Get on your CUmini, retract the side stand 3 Press "Unlock" button on the intelligent remote control. 4 Press the "Parking" button 5 The vehicle enters READY state. 6 Gently twist the throttle to ride TIPS on the road. Before riding, make sure the center stand is retracted. You can only start the vehicle when it's in the stationary state. If an error occurs while riding, please slide or push the vehicle to a safe area. Do not attempt to restart the vehicle while riding or in the driving lane to avoid danger. 15 RIDING GUIDE c. Tips for Riding 1 When the vehicle is starting, you should slowly accelerate in order to avoid excessive starting current caused by instantaneous rapid acceleration and increased energy consumption. 2 Under the premise of ensuring safety, try to maintain a constant speed, reduce frequent start, brake, instant acceleration, etc. to avoid increased energy consumption. 3 The maximum load for CUmini is 75KG. Overloading is strictly prohibited. 4 When pushing the vehicle, please press the "Parking" button or switch to Forward Mode to prevent accidents caused by sudden start of the vehicle due to unintentional turning of the throttle control. 5 Please hold up the center stand while parking, and press the "lock button" of the intelligent remote control. 16 BATTERY USE INSTRUCTION Battery Charging 1 1 Open the battery compartment. 2 Disconnect the battery pack main plug. 3 Take the battery pack out of the battery compartment. 17 4 Put the main plug of the charger into the battery charging port, and then connect the plug to a power supply. 5 The indicator illuminates red while the battery pack is being charged normally, and it turns gree when fully charged. BATTERY USE INSTRUCTION Battery Charging 2 1 Take out the charger. 2 Connect the main plug of the charger with the socket under the seat of the vehicle. 3 The indicator illuminates red while the battery pack is being charged normally, and it turns green when fully charged. Warning: Battery is strictly prohibited to get wet, flushed,or even submerged in water.Vehicle wading height should not exceed the bottom of the battery compartment, or it will cause the water inflow, short circuit,resulting in permanent battery failure. Under such circumstances, it is strictly forbidden to charge the vehicle or the battery again, otherwise it will cause the danger of internal fire, combustion and explosion. Please immediately transfer the battery to the service center for maintenance.This car is not equipped with air circuit-breaker, perform power-off protection when it is disconnected . 18 BATTERY USE INSTRUCTION TIPS 1 Charging temperatures: 0 - 40, discharging temperature: -15 - 45 . 2 Charge the battery pack after using, if you plan on not riding the vehicle for a long time, please take the battery pack out of the vehicle. 3 Forbidden to short-circuit the battery pack. 4 Please prevent children from touching the battery pack and forbidden to throw it into the fire. 5 Forbidden to impact or press strongly on the battery pack. 6 Only charge the battery pack with the designated special charger. Do not use unapproved chargers to charge the battery pack. 7 The battery pack and charger have been strictly inspected before leaving the factory, forbidden to disassemble the battery pack without authorization. 8 Do not park the vehicle indoors or in the hallway. Do not charge the vehicle indoors or in the hallway. The battery/vehicle should be kept away from combustible materials when charging. 9 Don't charge in a closed space, under the hot sun, or at high temperature, and the charging is not allowed to perform in the saddle or tailbox; 10 If the indicator is abnormal, odor occurs or the charger shell is overheated in the charging process, stop charging immediately, and overhaul or replace the charger. 11 Used batteries shall not be disassembled without authorization, but shall be collected by relevant departments. 19 BATTERY USE INSTRUCTION Storage, Maintenance and Transportation 1 If the vehicle is not used for a long time (such as winter, summer or other special circumstances), the battery must be removed and stored separately, and regularly maintained and charged. Otherwise, the battery can be completely drained, causing irreversible damage. Battery failure in such case will not be covered by warranty. 2 In case you plan on storing your battery pack for a long period of time, please disconnect the battery from the vehicle to prevent it from over-discharging. Keep the battery in a dry, ventilated place and fully charge it with the charger once every month. 3 The battery pack and charger should be stored in a clean, dry and well-ventilated place and avoid contact with corrosive substances, and be kept away from power, fire and heat sources. 4 Battery pack storage conditions: ambient temperature 0-25, ambient humidity 65%RH 5 Don't park the vehicle, or charge the battery/vehicle indoors,and avoid combustible materials when charging. 20 APP INSTRUCTIONS CUmini Smart Electric Motorcycle sup ports wireless communication, GPS, etc., which can connect the vehicle withyour smart phone. You can manage and check your vehicle using your smart phone through the SOCO App. Available on iOS and Android platforms, please check your smart phone operating system before installation. iOS platform: App requires iOS 9.0 or later. APP main features: On-Board Diagnostics: When the vehicle is ready to start , you can access the condition of the vehicle by performing a one-button examination. Android platform: App requires Android 4.4 or later. Anti-theft System The vehicle will sound the alarm when an unauthorized movement of the vehicle occurs. The app will notify the owner and track tracking the position of the vehicle. Data Record Users can access the vehicle information, battery level, distance travelled, tracking and other information through the APP. Social Networking Users can make friends and build the community through the app and enjoy the fun of riding online and offline. The functions of SOCO APP may vary with version update, function upgrade and different vehicle types .Please refer to the actual content of the latest version. 21 MAINTENANCE Regular maintenance can improve the service life and driving safety of CUmini Smart Electric Scooter. It is suggested that you take care of the vehicle following advices below: a. General cleaning and maintenance *Cleaning: Please use clear water and mild detergent to clean the vehicle, and use soft cloths and sponges to clean the surface. Please do not use metal brushes, sandpapers etc. to prevent the parts surface from scratching. After cleaning, dry it with a soft cloth. *Storage: Please move the vehicle to a dry and cool indoor place, reduce exposure to sun and rain to avoid rust and corrosion of parts, thereby prolong the service life of your vehicle. b. Warnings 1 Please do not use high-pressure washers to flush the vehicle directly, so as to avoid internal electrical parts and lines being exposed to water intrusion and soaking, which may cause vehicle mechanical failure or other potential accidents. 2 Before long-term storage, please disconnect the battery from the vehicle and avoid over discharging, and please charge the battery once a month. 22 COMMON PROBLEMS AND TROUBLESHOOTING METHODS a. FAQ and Troubleshooting Errors Causes Solutions No power, "start" 1. Battery is poorly connected won't light up. 2. The fuse is blown or in poor contact Twist the throttle, the motor won't start. 1.Low battery 2.Handle lever is not returned 3.Parking button is not switched off 4.Throttle fault 5.Controller connector is loose 6.Controller fault 7.Motor fault 1. Please check if the main battery plug is properly connected 2. Please change the fuse 1. Charge the battery 2.Return the handle lever 3.Press the parking button to unpark 4.Replace the throttle 5.Replug the controller connector 6.Replace the controller 7.Replace the motor Speed is slow or mileage is short. 1.Low battery 2.Flat tire 3.Overloading 4.Poor braking 5.Battery aging or reaching end of life 1.Charge the battery 2.Please inflate the tires to normal pressure before riding 3.Observe load limits 4.Replace brake pads and check the brake system before riding 5.Replace the battery Battery won't charge 1.The charging plug is poorly connected 1.Please check if the main plug is properly connected 2.Did not use the correct charger 2.Please use SOCO designated charger 3.Battery aging or reaching end of life 3.Replace the battery 23 COMMON PROBLEMS AND TROUBLESHOOTING METHODS b. Error Codes Errors Causes Solutions Error 99 on Dash Error 98 on Dash Error 97 on Dash Error 96 on Dash Error 95 on Dash Error 94 on Dash Error 93 on Dash Error 92 on Dash Error 91 on Dash Error 90 on Dash Error 89 on Dash Error 88 on Dash Error 87 on Dash Error 87 on Dash Controller communication fault Controller stops working (possibly overcurrent, locked-rotor, under voltage, overtemperature) Controller power transistor fault Controller Hall sensor fault Controller throttle fault Battery communication fault Charging overcurrent Charging overvoltage Battery at high temperature Discharging overcurrent Low temperature charging Low temperature discharging Internet connection fault GPS connection fault Please contact customer service or dealer Please stop for a while and then start again Please contact customer service or dealer Please contact customer service or dealer Please check the throttle wiring or contact customer service or dealer Please check the charging port connection, or contact customer service or dealer Please stop charging, and check the charger Please stop charging, and check the charger Please stop charging/riding wait until the battery temperature drops before attempting to ride If it keeps showing Error 90, please stop riding and wait for a moment Please take out the battery and charge it in a warm indoor place Please take the vehicle or battery to a warm indoor place, and wait for a moment Please move the vehicle to an open area, or contact customer service or dealer Please move the vehicle to an open area, or contact customer service or dealer 24 COMMON PROBLEMS AND TROUBLESHOOTING METHODS c. Battery Troubleshooting Status Before using In use In use Errors The battery has no power, no response when starting the vehicle When riding with low power, power off occurs when battery level drops below 10% Causes Low battery Low battery, low voltage protection, normal phenomenon Error 88 on Dash Low temperature discharging Solutions Charge the battery. Charge the battery. Please move the vehicle to a warm indoor place, and wait for a moment In use In use In use In use 25 Error 90 on Dash Error 91 on Dash Error 94 on Dash Overnight or next day, the dash shows a drop in power Discharging overcurrent High discharge temperature If it keeps showing Error 90, please stop riding and wait for a moment Please stop riding, switch off the air circuit-breaker and wait for a moment Battery communication fault Please check the charging port connection or contact customer service or dealer ECU, controller, alarm electrical components will drain the battery. Normal phenomenon Operate as normal COMMON PROBLEMS AND TROUBLESHOOTING METHODS Status In use Errors The mileage is different from official data Storage Start the vehicle, "Power" not on Charging Error 89 on Dash Charging Error 92 on Dash Charging The charger heats up during charging Causes Solutions Official Mileage is the one in a If you have any questions, please special environment and condition, and is related to road conditions, contact customer service or dealer weather, temperature, wind resistance, load capacity and other factors Battery has been stored for too long, power is used up Charge the battery. If it can't be charged, please contact customer service or dealer Low temperature charging Charging overvoltage Take out the battery and charge it in a warm indoor place Please stop charging, and check the charger Charging process of the charger internal current is high and will generate a lot of heat, the metal housing can effectively dissipate heat, which will lead to a higher temperature of the housing Operate as normal, and use the charger in a dry, ventilated place Battery flooded water The battery does not work The vehicle is rained on, soaked properly and the vehicle cannot be started in water, waded too deep in water, causing battery flooded water Stop using. Please contact customer service or dealer Battery shell broken The battery has been s impacted or dropped, causing the shell to break or crack Battery shell damage caused by the use of the vehicle Stop using. Please contact customer service or dealer 26 SOCO Smart Electric scooter Download App Bind your vehicle Android iOS Available on iOS and Android platforms, please check your smart phone operating system before installation. iOS platform: App requires iOS 9.0 or later. Android platform: App requires Android 4.4 or later. 27 CHECK LIST RANGE Brake fluid Tire pressure and wear Front and rear brake shoes wear Front and rear brake discs wear Front axle nut fastening Rear flat fork nut fastening Motor nut and retainer bolt fastening Front and rear shock bolt fastening Steering column locking nut Front disc brake bracket fastening (with threadlocker) Front brake disc fastening (with threadlocker) Rear disc brake bracket fastening (with threadlocker) Rear brake disc fastening (with threadlocker) Battery 1000 2500 5000 7500 10000 12500 15000 17500 20000 Torque KM KM KM KM KM KM KM KM KM 59N.m 59N.m 80N.m F.30N.m/ R.39N.m 60N.m 26N.m 42N.m 26N.m 42N.m Note: Check the lithium battery balance by BMS reading and manual measurement. www.supersoco.com MAINTENANCE RECORD Content MAINTENANCE RECORD Content Date Date MAINTENANCE RECORD Content MAINTENANCE RECORD Content Date Date MAINTENANCE RECORD Content MAINTENANCE RECORD Content Date Date Manufacturer:Yanaka (Xuzhou) New Energy Locomotive Co., Ltd. Address: Accessories Park, Hi-tech Industrial Development Zone, Changdian Town, Fengxian County, Xuzhou City, Jiangsu Province, China Assembly plant: Changzhou Kwang Yang Motor Co.,Ltd. Address: No.10 Lvtang Road, New North District, Changzhou City, Jiangsu Province, China The illustrations in this manual may dier from the actual products. We reserve the rights to modify drawings and products to improve quality and performance without prior notice.