Cookworks Food Processor

ELECTRICAL SAFETY

• Plug into a 220V-240V AC, 50Hz supply. Connecting to other sources may damage the appliance and invalidate the guarantee.
• Switch off and unplug when not in use and before cleaning or changing accessories.
• Not for use by children; keep appliance and cord out of reach.
• Can be used by persons with reduced physical, sensory or mental capabilities if supervised or instructed and hazards are understood.
• Children shall not play with the appliance.
• Keep motor housing, cable, and plug dry and away from splashes. Never immerse in water.
• Do not cover or block ventilation holes.
• Do not pull cable to disconnect.
• Do not operate if damaged or malfunctioning. Damaged cords must be replaced by a qualified service engineer.
• Position so plug is accessible and socket is within easy reach.

WARNING!

• Intended exclusively for domestic households; not suitable for commercial use.
• Always unplug the motor housing if unattended and before assembling, disassembling, or cleaning.
• Only use supplied and fully assembled parts.
• Do not cover the food processor; allow motor housing to cool fully before storing.
• Never use hot liquids; allow liquids to cool to room temperature before blending.
• Do not leave unattended during use.
• Blades are sharp; take care when emptying the bowl, fitting/removing blades, and cleaning.
• Do not fill above the maximum level marked on the bowl.
• Never place hands or utensils inside the processor bowl while in use. Use a scraper/spatula only when the processor is not in operation.
• Do not attempt to operate without the lid in place.
• Can cause personal injury if misused.

FOOD SAFETY

• Keep raw meat and poultry separate from cooked foods.
• Always wash hands after handling raw meat/poultry, before handling ready-to-eat foods.
• Wipe and disinfect surfaces in contact with raw meat/poultry.
• Use separate utensils for raw meat/poultry and cooked food, or wash thoroughly between uses.

PARTS

Diagram showing the following parts:

• 1. Pusher
• 2. Feed tube
• 3. Lid
• 4. General purpose blade
• 5. Blade support
• 6. Bowl
• 7. Motor housing
• 8. Speed switch
• 9. Slicing blade
• 10. Shredding blade
• 11. Julienne blade
• 12. Blade holder

IMPORTANT: The food processor is equipped with a safety feature and will not operate unless the lid and processor bowl are correctly fitted.

ASSEMBLY

1. Clean all parts thoroughly before first use and place the motor housing on a stable, flat surface.
2. Position the processor bowl onto the motor housing and align the arrow on the base of the bowl with the 'unlocked' padlock symbol on the top of the motor housing. Twist the bowl and align the arrow with the 'locked' padlock symbol. If the bowl is not correctly locked, the processor will not work.
3. Fit the blade support onto the drive shaft in the centre of the bowl.
4. Fit the blade of choice carefully:
   • For the general purpose blade, fit it over the blade support; the blade will rest close to the bottom of the bowl.
   • For slicing, shredding, or julienne blades, first fit the blade into the holder, then using the finger holes, fit the holder onto the blade support. The blade holder will sit near the top of the bowl. To fit the blade into the holder, align the blade with the cutting edge uppermost. Tilt the blade and hook the clip shown under the edge of the holder. Press downwards on the other edge to fully engage the blade.
5. Align the lugs on the rim of the bowl with the grooves on the underside of the lid and fit the lid onto the bowl. Twist the lid clockwise to lock into position. When correctly fitted, the protruding section of the lid covers the bowl handle. If the lid is not correctly locked, the processor will not work.
6. If adding ingredients via the feed tube, use the pusher where necessary.

FOOD PROCESSOR - BASIC OPERATION

1. Assemble the food processor as described in the Assembly section.
2. If using the general purpose blade, ingredients can be added into the bowl before fitting the lid. Advice for using julienne, slicing, and shredding blades is in the following section.
3. Fully unwind the food processor cable and plug in.
4. Switch on at the mains and use the speed switch to select the desired speed. Speed 1 provides a slower mix; speed 2 provides a faster mix. Use for a maximum of 90 seconds.
5. Switch off and allow the blade or blade holder to stop spinning before checking the consistency of the mix/cut. If satisfactory, remove the processor bowl from the motor housing.
6. If further mixing is required, wait 2 minutes before restarting the processor. If the unit is used for 3 consecutive cycles, wait 30 minutes before the next use.
7. To use the processor on pulse, turn and hold the speed switch to the 'P' position for short intervals. The processor will operate at full speed; release the switch when the desired mix is achieved.
8. To stop or interrupt, switch the appliance off by turning the speed control switch to the off (0) position or by turning off at the mains.

FOOD PROCESSOR - USING THE ACCESSORIES

General purpose blade

The general purpose blade is the most versatile attachment, used for chopping meats, bread, and vegetables, making pastry, mixing cakes, and blending heavier liquids. It is not suitable for crushing or grinding coffee beans or converting granulated sugar to icing sugar.

• Cut food (meat, bread, vegetables) into 2cm cubes before processing.
• When making pastry, cut chilled fats into 2cm cubes before processing.
• Do not over-process; use for a maximum of 90 seconds. If further mixing is required, wait 2 minutes before restarting. If used for 3 consecutive cycles, wait 30 minutes before the next use.
• Usual process speed: speed 1 for softer mixtures/ingredients, speed 2 for harder mixtures/ingredients.

Chipping, slicing or shredding blades

These blades are used for grating, slicing, or shredding hard cheese and firm vegetables (e.g., carrots, potatoes, beetroot, onions).

• Fit the desired blade into the blade holder.
• Assemble the processor with the blade holder fitted onto the blade support, but do not add ingredients into the bowl yet.
• Cut ingredients into sizes that fit down the feed tube. Remove any peel and stones. For julienne vegetables, ensure they are not too short when added.
• Switch the processor on and feed ingredients down the feed tube onto the cutting blade, using the pusher to maintain contact with the spinning disc and even pressure.
• Use for a maximum of 90 seconds. If further slicing/shredding is required, wait 2 minutes before restarting. If used for 3 consecutive cycles, wait 30 minutes before the next use.
• Usual process speed for these accessories is speed 2.

CLEANING

Clean the food processor after each use. Take care when handling blades; they are sharp and can cause personal injury. Do not clean any part of this appliance in a dishwasher.

1. Switch off and unplug the appliance.
2. Remove the lid and separate processor bowl from the motor housing.
3. If fitted, lift off the blade holder from the support using the finger holes.
4. Remove shredding, slicing, and julienne blades from the holder before washing. To separate a blade from the holder, turn the holder over and from the reverse, press in the direction shown on the clip to release the blade.
5. Lift out the blade support and remove the general purpose blade (if fitted).
6. Wash all loose parts in hot water with a little washing-up liquid. Rinse and wipe dry.
7. Wipe the outside of the motor housing with a damp cloth; do not use detergent or abrasives as they may scratch the surface. Never immerse the motor housing, cable, or plug in water.

TECHNICAL SPECIFICATION

RECYCLING ELECTRICAL PRODUCTS

Recycle waste electrical goods to help the environment. The symbol [crossed-out wheelie bin symbol] indicates electrical products should not be disposed of with normal household waste. Ensure it is taken to a suitable facility for disposal.

Visit www.recycle-more.co.uk, click on "bank locator", and enter your postcode to find your nearest recycling site.

PLUG / WIRING ADVICE

The wires in this mains lead are coloured according to the UK electrical code: BLUE = NEUTRAL, BROWN = LIVE.

Non-rewireable plug

This appliance may be fitted with a "non-rewireable" plug. If the fuse needs changing, the fuse cover must be refitted. If the fuse cover is lost or damaged, the appliance must not be used.

Rewireable plug

Wire colours may not correspond with terminal markings. Rewireable plugs should only be replaced by a suitably competent person. Consult a qualified electrician if in doubt.

Diagram showing plug wiring:

• The BLUE wire must be connected to the terminal marked with the letter N.
• The BROWN wire must be connected to the terminal marked with the letter L.

Produced in China.

Argos Limited, 489-499 Avebury Boulevard, Milton Keynes, MK9 2NW.

Argos (N.I.) Ltd, Forestside Shopping Centre, Upper Galwally, Belfast, United Kingdom, BT8 6FX.

Argos Distributors (Ireland) Limited, Unit 7, Ashbourne Retail Park, Ballybin Road, Ashbourne, County Meath, Ireland.

www.argos.co.uk/cookworks

Tel: 0345 640 3030

PRODUCT GUARANTEE

This product is guaranteed against manufacturing defects for a period of 1 Year.

The product is guaranteed for twelve months from the date of original purchase. Any defect due to faulty materials or workmanship will be replaced, refunded, or repaired free of charge by the dealer from whom you purchased the unit.

The guarantee is subject to the following provisions:

• Does not cover accidental damage, misuse, cabinet parts, knobs, or consumable items.
• Must be correctly installed and operated according to the instructions in this manual. A replacement manual can be obtained from www.argos-support.co.uk.
• Must be used solely for domestic purposes.
• Guarantee invalidated if the product is re-sold or damaged by inexpert repair.
• Specifications are subject to change without notice.
• Manufacturer disclaims liability for incidental or consequential damages.
• Guarantee is in addition to, and does not diminish, statutory or legal rights.

Guarantor: Argos Ltd

489-499 Avebury Boulevard

Central Milton Keynes

MK9 2NW

www.argos-support.co.uk