Roksan | Hi-Fi & Audio Electronics
User Guide for ROKSAN models including: Attessa Turntable, Attessa, Turntable
File Info : application/pdf, 2 Pages, 469.56KB
DocumentDocumentLet's get started Attessa Turntable Quick Start Guide 1 Place in suitable location 0º Material Specifications Plinth Isolation Platter Platter weight Pulley Main Bearing Spindle Main Bearing Ball Main Bearing Housing Removable Dust Cover Tonearm Tonearm Type Tonearm Bearing Bearing Arm Material Internal wiring Effective Mass Recommended Tracking Weight Effective Length Overhang Headshell Offset Angle Cartridge Recommended Load Capacitance Recommended Load Impedance Vertical Tracking Angle Stylus Tip DC Resistance Isolated single plinth design 1-level decoupling High Mass 10mm Glass Platter with Anodised Aluminium edge 1.82 Kg Solid Aluminium Grade 303 Stainless Steel Steel (Grade 303) Brass (Grade CZ 121) Bespoke moulded PMMA acrylic Unipivot Single Jewel Stainless steel unipivot Hybrid construction. Precision formed 5052 Aluminium top with lightweight ABS bottom section. 0.08 OFC copper wire 14.9 g 1.8-2.2 g (2.0 g standard) 240 mm 17.5 mm 22.9 degrees 50-100 pF 47 k 23 degrees Diamond titanium 800 ± 20% Coil Impedance Output Voltage Output Balance Frequency Response Channel Separation Turntable Max Speed Variation Rumble (silent groove, unweighted) Dimensions Dimensions (Inc. Lid) Dimensions (Exc. lid) Weight Technical Motor Speed Controller Speed Phono Stage Phono Stage Bypass Phono stage gain (1 kHz) Phono Stage Signal to Noise THD+N Phono Stage output impedance Outputs Phono Output Mains input Power consumption 3.2 k ± 20% @ 1 kHz 3.5 mV ± 3 dB @ 1 kHz 1.5 dB or less @ 1 kHz Measurement point 10 kHz / 1 kHz + 1 dB ~ +7dB Measurement point 1 kHz over 22 dB +/- 0.54% at 33.3 RPM -44.36 dB H115 x W432 x D353 mm H104.5 x W432 x D383 mm 6.32 Kg Vibration Isolated 24 Pole Synchronous Built in high precision digitally synthesised AC signal generator with high current low distortion output 33 RPM & 45 RPM (Switchable) Built in MM phono stage Yes, (switchable on rear) 46 dB 70 dB (5 mV, 1 kHz sine wave, A-weighted) 0.04% (5 mV, 1 kHz sine wave) ~56 RCA with supplied low capacitance phono cable 5 V 1.5 A external SMPS (Operational down to 85 VAC) <0.5 W in standby. Full Power: 25 W max Read me, keep me or recycle me Roksan 24 Brook Road, Rayleigh, Essex, United Kingdom, SS6 7XJ | +44 1268 740 580 | info@roksan.com | roksan.com ROK 1417 | Version 1 3 Install Anti-Skate Weight 4 Remove Tonearm clamp 2 Install Platter 5 Adjust tracking weight 2g 1.8g - 2.2g 33 45 Step 6 6 Place Record Mat and record on Platter and check azimuth Azimuth 33 45 0º Step 7 7 Product overview Record Matt Tonearm 33 45 Standby 33 / 45 RPM Switches Platter Cartridge 8a Connect to amplifier with phono stage (Attessa Integrated/Streaming Amplifier) PASSIVE ACTIVE Passive 8b Connect to amplifier without phono stage PASSIVE ACTIVE Active 9 Power on Phono Input Analogue RCA 10 Change RPM speed 33 RPM 45 RPM 33 45