User Manual for AXLS models including: AX-M80 Stainless Steel Commercial Planetary Mixer, AX-M80, Stainless Steel Commercial Planetary Mixer, Steel Commercial Planetary Mixer, Commercial Planetary Mixer, Planetary Mixer
AX-M80 80 Quart Mixer | MVP Group Corp
Parts and Service | MVP Group Corp
File Info : application/pdf, 7 Pages, 3.14MB
DocumentDocumentI N D E X CONTENTS (1) Installation diagram (2) Specification (3) Installation 1. Location 2. Electrical connect 3. Rotation 4. Lubrication (4) Operation (5) Operation 1. Speed selection 2. Speed control 3. Application of Agitators (6) Wiring Diagram AX-M80 USER MANUAL PAGE 2 3 3 3 4 4 5 5 5 6 7 7 8 1. Installation diagram (MM) C B A G D F MODEL NO. AX-M80 E A B C D E F G 780 560 1440 1060 850 510 720 2. Specifications Model No. AX-M80 Mixing Capacity Flour / Dough 34 kgs 60 kgs Motor HP 3 Machine Weight Stainless Steel Bowl (Aprrox) (cm) 500 Kgs 52x48 (80 qt.) Motor & Electrical : Two speeds, Available only in three phase electric. Transmission: The transmission is made by alloy steel gears. The power from motor to the transmission is transmitted by fiber V-belts. Two speed transmissions with two speed motor gives 2 a 4 speed mixer. Speed : Four speed transmission: 60HZ / 50HZ First Agitator (RPM) 135 / 113 Second 195 / 162 Third 237 / 198 Fourth 341 / 284 SS Safety Guard : Stainless steel safety guard is an standard. Smoothly rotate open with a limit switch to shut off power immediately to protect operator. Attachment Hub : #12 attachment Hub is optional, the operator can use any of the standard attachments on the market, such as vegetable slicer, meat grinder, etc. Standard Attachment : Bowl -1, Hook - 1, Beater -1, Whipping Ball -1, Bowl Truck - 1 3. Installation Location Place the mixer in its operating location. There should be adequate space around the mixer for the user to operate the control and install and remove bowls. Holes are provided in the base to permanently secure the mixer, although this not necessary in normal installations. Floor models must be leveled front-back and side-to-side by sliding shims under the legs as required. Electrical connect Electrical connections should be made by qualified personnel in accordance with applicable codes and regulations. Permissible voltage fluctuation is ± 10% of nominal voltage. Be sure to tag any electrical outlets, fuses, or connections involved in installing the mixer until installation has been completed. Rotation Wrong rotation may cause the mixer damage. 4. Lubrication 3 1 2 Transmission gears are already filled with enough lubricant oil. If the oil level falls below the gauge line, add more oil. Remove the oil-fill plug (1 fig.1) in the cover of the transmission case and insert a tubing, pour enough oil into it. Reinstall and tighten oil-fill plug. ALL MACHINES ARE ALREADY FILLED WITH ENOUGH LUBRICANT OIL WHEN LEAVING OUR FACTORY. 5. Operation Open the safety guard. Install the bowl and one accessory on the mixer. Place the ingredients into the bowl. Close the safety guard and release the button of emergency stop. Lift the bowl by bowl-up switch (arrow up). Set the speed selectors `Motor Speed Shift Switch' & `Gear Speed Shift Handle' at desired speed and then press button marked "ON" For non-timed operation, set speed selectors at desired speed, set DIGITAL TIMER on "OF" position, and press the button marked "ON" For timed operation, set speed selectors at desired speed, set DIGITAL TIMER h on desired time period, auto shut off machine in any speed after preset time has elapsed. When operation is finished, turn off motor by pressing "OFF" button or "emergency stop". CONTRL PANEL WITH DIGITAL TIMER 4 NOTE: TO START THE MOTOR, PRESS "ON" BUTTON, THE SPEED SELECTOR HANDLE MUST BE AT THE NUMBERS, INDICATING A SPEED, NOT AT AN INTERMEDIATE POSITION. Speed Selection: Speed selection is made by `Motor Speed Shift Switch' & `Gear Speed Shift Handle' with the number on the control panel. 1st speed: Set `Motor Speed Shift Switch' to low speed, and set `Gear Speed Shift Handle' to "1" low speed. 2nd speed: Set `Motor Speed Shift Switch' to high speed, and set `Gear Speed Shift Handle' to "2" high speed. 3rd speed: Set `Motor Speed Shift Switch' to low speed, and set `Gear Speed Shift Handle' to "3" low speed. 4th speed: Set `Motor Speed Shift Switch' to high speed, and set `Gear Speed Shift Handle' to "4" high speed. NOTE: TO CHANGE SPEED, STRICTLY DO ACCORDING TO FOLLOWING STEPS: First: Turn off motor by turning `Motor Speed Shift Switch' to "STOP" position. Second: Shift `Gear Speed Shift Handle' to desired speed. Third: Turn `Motor Speed Shift Switch' to desired speed. The number "1" (low) is for heavy mixtures like dough, heavy batter and potatoes. 5 The number "2" (medium-low) is for mixing cake batter, mashing potatoes and for developing dough. The number "3" (medium-high) is for mixing maximum incorporation of air into light batches, the whip is used for whipping cream beating egg white mixing light icings meringues and whipping. The number "4" (high) is for accelerated mixing maximum air incorporation into light batches similar to number "3" Bowl: Stainless steel bowl is sanitary open rim design to meet today's exact requirement. Bowl lift: Mixer has equipped a POWER LIFT and operate by up/down (arrow) on the control panel. Agitators: When placing an agitator on agitator shaft, lower the bowl, push agitator up on shaft and turn agitator until drive pin on shaft reaches L-shaped slot in agitator shank. Application of agitators Wire Whip: Egg Whites, Mayonnaise, Meringue, Whipped Cream Flat Beater: Mashed Potatoes, Mayonnaise, Waffle or Hot Cake Batter, Cake-Box or Slab, Cake-Cup, Cake-Layer, Cake-Pound, Cookies Sugar, Dough-Pie, Eggs & Sugar for Spong Cake, Icing-Fondant, Shortening & Sugar-Creamed. Dough Arm: Dough-Bread or Roll, Dough-Heavy Bread, Dough-Pizza, Dough-Raised Donut, Dough-Whole wheat, Pasta-Basic, Egg Noodle. Attachment Hub: (NO.12) designed to accommodate attachments such as a meat chopper, a food chopper, and a food slicer/shredder. The machine should not be used for mixing while hub attachments are installed. DO NOT USE ATTACHMENT HUB WHILE MIXING. 6. Wiring Diagram 6 3560 NW 56th Street Fort Lauderdale, FL 33309 Tel.: 786.600.4687 / Toll Free: 844.218.8477 Fax.: 786.661.4100 5659 Royalmount Avenue Montreal, Qc, Canada H4P 2P9 Tel.: 514.737.9701 / Toll Free: 888.275.4538 Fax.: 514.342.3854 / Toll Free: 877.453.8832 service@mvpgroupcorp.com sales@mvpgroupcorp.com www.mvpgroupcorp.com 7