Edgecore-Open Infrastructure for the Enterprise & Service Provider
User Guide for EdgecorE models including: AS7535-28XB Ethernet Switch, AS7535-28XB, Ethernet Switch, Switch
CSR440 – Edgecore Networks
File Info : application/pdf, 8 Pages, 1,013.88KB
DocumentDocumentQuick Start Guide Ethernet Switch AS7535-28XB | AS7535-28XBE Package Contents www.edge-core.com 1 1. AS7535-28XB/AS7535-28XBE (includes 2 PSUs and 6 fan trays) 2. Rack Mounting Kit--2 brackets and 8 screws 3. Grounding kit--grounding lug, 2 screws, and 2 washers 2 3 4 5 4. (Optional) AC power cord 5. Documentation--Quick Start Guide (this document) and Safety and Regulatory Information Overview 1 4 67 8 12 2 9 3 10 5 11 13 1. 2 x DC or AC PSUs 7. BITS/ToD RJ-45 timing ports 2. 2 x 100G QSFP28 ports 8. 10MHz/1PPS I/O 3. 2 x 400G QSFP-DD ports 9. GNSS antenna 4. 24 x 25G SFP28 ports 10. USB Type C storage port 5. Product tag 11. RJ-45 alarm port 6. Management I/O: 1000BASE-T RJ-45, RJ-45 console, 12. 6 x fan trays Micro-USB console, reset button 13. Grounding screw Status LEDs 6 7 4 1 2 3 5 1. PSU LED: Green (OK), Amber (fault) 2. QSFP-DD Port LEDs: Blue (400G), Cyan (200G), Green (100G), Yellow (50G) 3. QSFP28 Port LEDs: Green (100G), Cyan (50G), Magenta (40G), Blue (25G), Yellow (10G) 4. SFP28 Port LEDs: Blue (25G), Green (10G), Cyan (1G) FRU Replacement 5. System LEDs: PSU1/2 -- Green (OK), Amber (fault) DIAG -- Green (OK), Orange (fault detected) FAN -- Green (OK), Orange (fault) LOC -- Blinking Blue (OK) ALARM -- Green (OK), Red (alarm) 6. RJ-45 Management Port LEDs: Left (link), Right (activity) 7. BITS/ToD LEDs: Green (valid BITS), Blinking Green (1PPS ToD) PSU Replacement 1. Remove the power cord. 2. Press the release latch and remove the PSU. 3. Install replacement PSU. Fan Tray Replacement 1. Loosen the fan tray screw. 2. Pull out and remove the fan tray. 3. Install replacement fan tray. 1 E052023-CS-R02 150200002489A Installation Quick Start Guide Warning: For a safe and reliable installation, use only the accessories and screws provided with the device. Use of other accessories and screws could result in damage to the unit. Any damages incurred by using unapproved accessories are not covered by the warranty. Avertissement: Pour une installation sûre et fiable, utilisez uniquement les accessoires et les vis fournies avec l'appareil. L'utilisation d'autres accessoires et vis pourrait endommager l'appareil. Les dommages causés par l'utilisation d'accessoires non approuvés ne sont pas couverts par la garantie. Caution: The device must be installed in a restricted-access location. Attention: L'appareil doit être installé dans un emplacement à accès restreint. Note: The device has the Open Network Install Environment (ONIE) software installer preloaded, but no software image. Information about compatible software can be found at www.edge-core.com. Note: The drawings in this document are for illustration only and may not match your particular model. 1 Mount the Device in an EIA-310 Rack 2 Ground the Device Rear Panel Side Panel Verify Rack Ground Ensure the rack is properly grounded and in compliance with international and local standards. Verify that there is a good electrical connection to the grounding point on the rack (no paint or isolating surface treatment). Attach Grounding Wire Attach the grounding wire (#14 AWG/1.5 mm2, green with yellow stripe) to the grounding point on the device's rear panel or side panel. Then connect the other end of the wire to rack ground. Caution: The earth connection must not be removed unless all supply connections have been disconnected. Attention: Le raccordement à la terre ne doit pas être retiré sauf si toutes les connexions d'alimentation ont été débranchées. 3 Connect Power a. AC Power 1 1. For a 300mm-deep rack, use the four front screw holes to attach each of the brackets to the device with four of the included bracket screws. (For a 280mm-deep rack, use the four recessed screw holes.) Install one or two AC PSUs in the device, if they are not already installed in the factory. Then connect an external AC power source to the PSUs. b. DC Power 2 2. Use the screws and cage/clip nuts supplied with the rack to secure the device in the rack. Install one or two DC PSUs in the device, if they are not already installed in the factory. Connect an external DC power source to the PSUs. Or, connect to a notolerance DC mains supply with a UL/CSA-approved circuit breaker rated at 16 A. 2 Quick Start Guide Caution: Before connecting power supply cables to the device, ensure that power to the feed lines is turned off at the supply circuit breaker or disconnected from the power bus. Attention: Avant de connecter les câbles d'alimentation à l'appareil, assurez-vous que l'alimentation des lignes d'alimentation est coupée au niveau du disjoncteur d'alimentation ou déconnectée du bus d'alimentation. Caution: Use a UL/IEC/EN 60950-1 and/or 62368-1 certified power supply to connect to a DC converter, and a #14 AWG/1.5 mm2 (for -44 VDC to -60 VDC PSU) wire to connect to a DC PSU. Attention: Utilisez une alimentation certifiée UL/IEC/EN 60950-1 et/ou 62368-1 pour le connecter à un convertisseur CC et un câble AWG #14/1.5 mm2 (pour -44 VDC à -60 VDC) pour vous connecter à une alimentation CC. Caution: All DC power connections should be performed by a qualified professional. Attention: Toutes les connexions d'alimentation CC doivent être effectuées par un professionnel qualifié. The following transceivers are supported in the QSFP28 ports: 100GBASE-SR4, PSM4, LR4, ER4, ZR4, CR4, AOC 40GBASE-SR4, PSM4, LR4 The following transceivers are supported in the SFP28 ports: 25GBASE-SR, LR, BX BiDi 10GBASE-SR, LR, CR, BX BiDi, T 1000BASE-SX, LX, BX BiDi, T 5 Connect Timing Ports 2 3 1 1. Connect the ground wire / protective earth. 2. Connect the -44 -60 VDC wire. 3. Connect the DC return wire. Note: It is suggested to use the following for DC power: One UL 1015 AWG#10-14 stranded wire, 2m maximum (-44VDC -60VDC: Input+) One UL 1015 AWG#10-14 stranded wire, 2m maximum (VDC return: Input-) One UL 1015 AWG#10-14 stranded wire, 2m maximum, (green/yellow) green with yellow stripe (PE) Note: The DC terminal screws should be tightened to a torque of 7 in-lbs maximum. 4 Make Network Connections RJ-45 BITS/ToD Use Cat. 5e or better twisted-pair cables to connect the BuildingIntegrated Timing Supply (BITS) and Time of Day (ToD) ports to other synchronized devices. 10MHz/1pps Use coax cables to connect the 10 MHz and 1-pulse-per-second (1PPS) ports to other synchronized devices. GNSS Antenna Attach an external antenna to the GNSS antenna port for clock synchronization with GPS time. 6 Make Management Connections QSFP-DD/QSFP28/SFP28 Ports Install transceivers and then connect fiber optic cabling to the transceiver ports. Alternatively, connect AEC/AOC/DAC cables directly to the QSFPDD/QSFP28/SFP28 slots. The following transceivers are supported in the QSFP-DD ports: 400GBASE-SR8, DR4, FR4, AEC cable Mgmt RJ-45 Port Connect Category 5, 5e or better twisted-pair cable. RJ-45 Console Port Use an RJ-45-to-DB-9 null-modem console cable (not included) to connect to a PC running terminal emulator software. Use a USB-to-male DB-9 adapter cable (not included) for connections to PCs that do not have a DB-9 serial port. Configure the serial connection: 115200 bps, 8 characters, no parity, one stop bit, 8 data bits, and no flow control. Console cable pinouts and wiring: Device's RJ-45 Console Null Modem PC's 9-Pin DTE Port 6 RXD (receive data) <---------------- 3 TXD (transmit data) 3 TXD (transmit data) ----------------> 2 RXD (receive data) 4,5 SGND (signal ground) ------------------ 5 SGND (signal ground) 3 Hardware Specifications Size (WxDxH) 438.4 x 300 x 43.3 mm (17.26 x 11.81 x 1.7 in.) Weight Temperature 6.8 kg (14.99 lb), with two installed PSUs Operating: -40° C to 65° C (-40° F to 149° F) Transportation: -40° C to 85° C (-40° F to 185° F) Storage: -40° C to 85° C (-40° F to 185° F) Humidity Operating: 5% to 95% (non-condensing) Power Consumption (at 25° C) System Input Rating Maximum: 383.6 W Typical: 164.03 W Minimum: 95.11 W AC Input: 100240 VAC, 5060 Hz, 6.02.4 A 100-120 VAC, 50/60 Hz, 6.0 A Max or 200-240 VAC, 50/60 Hz, 3.0 A Max DC Input: -44 -60 VDC, 15.59.6 A Regulatory Compliances Emissions EN 55032 EN 61000-3-2 EN 61000-3-3 FCC Title 47, Part 15, Subpart B, Class A VCCI-CISPR 32 BSMI Class A Immunity EN 55035 IEC 61000-4-2/3/4/5/6/8/11 Environmental Storage: ETSI EN 300 019-1-1 Class 1.1 Temperature: -40° C to 85° C (-40° F to 185° F) Transportation: ETSI EN 300 019-1-2 Class 2.3 Temperature: -40° C to 85° C (-40° F to 185° F) Operating Conditions: ETSI EN 300 019-1-3 Class 3.2 Temperature: -40° C to 65° C (-40° F to 149° F) Relative Humidity: 5% to 95% Safety UL (CSA 22.2 No 62368-1 & UL 62368-1) CB (IEC/EN 62368-1, 2nd & 3rd Ed) BSMI CNS 15598-1 Quick Start Guide Warranty Information and Technical Support Registering your product enables you to receive a more efficient warranty service. Be sure to register at www.edge-core.com. 4 AS7535-28XB | AS7535-28XBE www.edge-core.com 1 2 3 4 5 1. AS7535-28XB/AS7535-28XBE 2 PSU 6 ) 2. --2 8 3. -- 2 2 4. AC 5. 1 4 67 8 12 2 9 3 10 5 11 13 1. 2 x DC AC PSU 7. BITS/ToD RJ-45 2. 2 x 100G QSFP28 3. 2 x 400G QSFP-DD 8. 10MHz/1PPS I/O 9. GNSS 4. 24 x 25G SFP28 10. USB Type C 5. 6. I/O1000BASE-T RJ-45RJ-45 Micro-USB 11. RJ-45 12. 6 x 13. LED 6 7 4 1 2 3 5 1. PSU LED (OK) 2. QSFP-DD LED (400G) (200G) (100G) (50G) 3. QSFP28 LED (100G) (50G) (40G) (25G) (10G) 4. SFP28 LED (25G) (10G) (1G) FRU 5. LED PSU1/2 -- DIAG -- FAN -- LOC -- -- 6. RJ-45 LED ) ) 7. BITS/ToD LED BITS) (1PPS ToD) PSU 1. 2. PSU 3. PSU 1. 2. 3. 5 #14 AWG/1.5 mm2 Open Network Install EnvironmentONIE www.edge-core.com 3 a. AC 1 EIA-310 AC PSU AC PSU b. DC 1 1. 300mm 280mm 2 2. 2 DC PSU DC PSU DC UL/ CSA 16A UL/IEC/EN 60950-1 / 62368-1 DC #14 AWG/1.5 mm2 -44 VDC -60 VDC PSU DC PSU DC 2 3 1 1. 2. -44 -60 VDC 3. DC 6 DC UL 1015 AWG#10-14 2m -44VDC -60VDC + UL 1015 AWG#10-14 2m VDC - UL 1015 AWG#10-14 2m / (PE) DC 7 in-lbs 6 4 QSFP-DD/QSFP28/SFP28 AEC/DAC QSFP-DD/QSFP28/SFP28 QSFP-DD 400GBASE-SR8DR4FR4AEC QSFP28 100GBASE-SR4PSM4LR4, ER4ZR4CR4AOC 40GBASE-SR4PSM4LR4 SFP28 25GBASE-SRLRBX BiDi 10GBASE-SRLRCRBX BiDiT 1000BASE-SXLXBX BiDiT 5 Mgmt RJ-45 Category 55e RJ-45 RJ-45- -DB-9 USB- - DB-9 DB-9 115200 bps8 1 8 RJ-45 9 DTE 6 RXD <---------------- 3 TXD 3 TXD ----------------> 2 RXD 4,5 SGND ------------------ 5 SGND RJ-45 BITS/ToD 5e (BITS) (ToD) 10MHz/1pps 10 MHz 1 (1PPS) GNSS GPS GPS 7 x x 438.4 x 300 x 43.3 mm (17.26 x 11.81 x 1.7 in.) 6.8 kg (14.99 lb) PSU -40° C 65° C (-40° F 149° F -40° C 85° C -40° F 185° F -40° C 85° C -40° F 185° F 5% 95% 25° C 383.6 W 164.03 W 95.11 W AC 100240 VAC5060 Hz6.02.4 A 100-120 VAC50/60 Hz 6.0 A 200-240 Vac50/60 Hz 3.0 A DC -44 -60 VDC15.59.6 A EN 55032 EN 61000-3-2 EN 61000-3-3 FCC Title 47, Part 15, Subpart B, Class A VCCI-CISPR 32 BSMI Class A EN 55035 IEC 61000-4-2/3/4/5/6/8/11 Storage: ETSI EN 300 019-1-1 Class 1.1 Temperature: -40° C to 85° C (-40° F to 185° F) Transportation: ETSI EN 300 019-1-2 Class 2.3 Temperature: -40° C to 85° C (-40° F to 185° F) Operating Conditions: ETSI EN 300 019-1-3 Class 3.2 Temperature: -40° C to 65° C (-40° F to 149° F) Relative Humidity: 5% to 95% UL (CSA 22.2 No 62368-1 & UL 62368-1) CB (IEC/EN 62368-1, 2nd & 3rd Ed) BSMI CNS 15598-1 8