Instruction Manual for AVIANCE lighting models including: HD15272 3-Light Brushed Nickel Convertible Mini Chandelier, HD15272, 3-Light Brushed Nickel Convertible Mini Chandelier, Brushed Nickel Convertible Mini Chandelier, Nickel Convertible Mini Chandelier, Convertible Mini Chandelier, Mini Chandelier, Chandelier
2 дня назад — HD15272. ◇ WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER. ◇ ATTENTION! COUPER LE COURANT AU FUSIBLE OU UN DISJONCTEUR. ASSEMBLING THE FIXTURE (Fig.1).
ASSEMBLING & INSTALLATION INSTRUCTIONS The drawing shown may not exactly match the product enclosed. However, the installation instructions do apply to this product. HD15272 WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER. ATTENTION! COUPER LE COURANT AU FUSIBLE OU UN DISJONCTEUR. ASSEMBLING THE FIXTURE (Fig.1) 1. Return the arms to suitable position, see figure.2 2. Attach the loop (A) to the top center pipe nipple of the fixture body(B) by turning it clockwise until tight. Raise the cover (F) to bottom the plate of the fixture body (B) and lock it securely with ball nut (E). Put the socket sleeve (C) onto the socket (D). 3. Install the light bulbs in accordance with the fixture specifications. NOTE: DONOT EXCEED THE SPECIFIED WATTAGE! fixture. FIG.1 FIG. HANGING THE FIXTURE (Fig.1) 1. Shut off the power at the circuit breaker and remove old fixture from ceiling, including the old single bar. 2. Carefully unpack new fixture and lay all the parts on a clear surface. 3. Thread the two studs into the pre-drilled holes in the Mounting plate spaced the same distance apart as the holes in the canopy. Attach the Mounting plate to the Junction Box with the two Junction Box Screws as shown. The side of the Mounting plate marked "GND" must face to out. 4. Using proper chain pliers to open one end link of the chain provided and connect to the fixture loop. Close the link. 5. By measuring, determine correct number of links needed for proper hanging height. Using proper chain pliers disconnect and discard remaining chain. 6. Lace the fixture wires through the chain. Open the other end link of the chain and hang the fixture on the loop at the ceiling. Close the link. 7. Feed the fixture wires through the loop of the canopy and pull until taut. 8. Slide canopy up flush to ceiling, lock it securely with ball nut. **If you not need assembly the fixture loop , please pause and refer to Fig 4. 1. Take out the bottom loop of the canopy, then take the canopy to the fixture body, lock it with the shim and hex nut until tight. 2. Attach the fixture body to the ceiling, lock it securely with the ball nut CONNECTING THE WIRES (Eig3) 1. Take the black wire from the ceiling junction box and the smooth1wire leg from the fixture and twist bare ends together. Twist wire connector onto end of wire until snug. Repeat same process with white junction box wire and ribbed wire leg of fixture wire. NOTE: Twist wires together in the same direction you twist the wire connector onto wires. 2. If your junction box has a grounding wire (green or bare copper).attach this wire and the bare copper wire from the fixture together as step l. If junction box has no ground wire, attach the bare copper fixture wire to the green ground screw on the single bar. Tuck these wire connections neatly into the ceiling outlet box and then raise the canopy all the way to the ceiling. Lock it securely with ball nut. Your installation is now complete. Return power to the junction box and test the FIG. FIXTURE WIRES Black or Smooth FIXTURE WIRES White or Ribbed HOUSE WIRES Black(Hot) HOUSE WIRES White (Neutral) FIXTURE WIRES Bare Copper (Ground) HOUSE WIRES Green or Bare Copper(Ground) Thank you for purchasing an AVIANCE product. Need assistance with parts or assembly? Please email customer service at:info@aviancelighting.net ©COPYRIGHT ALL RIGHTS RESERVED. AVIANCE LIGHTING,INC. DOC202503HD15272WPS 文字