Installation Guide for HITRON models including: SSR-3 Combined Technology Sensor for Automatic Sliding Doors, SSR-3, Combined Technology Sensor for Automatic Sliding Doors, Technology Sensor for Automatic Sliding Doors, Sensor for Automatic Sliding Doors, Automatic Sliding Doors, Sliding Doors
Product Manuals | C Prox Ltd Including Quantek
SSR-3 Quick Installation Guide 1. MOUNT THE SENSOR Using the mounting template supplied mount the sensor within 50mm of the bottom of the door controller cover 2. SET MAIN DIPSWITCHES AS ILLUSTRATED Dip Switch X Dip Switch Y ON 12 34 5 6 7 12 34 56 ON Presence Timer: 30s I.R Frequency (Change if another SSR-3 is close by) Monitor Mode: Normal Safety Relay Output: N.C Reflection Diagnostics: OFF Radar +IR rows 2+3/ Radar only Door Hold Open: OFF Door Learn: OFF Test Input: ON (Set to OFF for NonEN16005 doors) Output: N.O. Detection: ON 3.2m (10.5ft) Activation Direction 3. CONNECT TO THE DOOR CONTROLLER Note: For EN16005 door controllers set Y6 to "ON" and connect the Gray & Brown wires to the door controller. If the door controller does not have a "TEST INPUT" set Y6 to "OFF" and do not connect the Gray & Brown wires Sensor's Cable Cable Red Black White Green N.O. COM Power Non Pole Activation Output RADAR + IR rows 2+3 OFF Y ON 6 Yellow(+) Blue(-) Gray(+) Brown(-) Opto Relay Test-P Test-N Safety Output Rows - 1,2,3 Test Input Door Controller 4.LED INDICATORS Green Flashing Green Flashing Green (once) Blue Red Slow flashing Red Fast flashing Red Orange Fast flashing Orange Slow flashing Orange Fast flashing Green/Red Slow flashing Green/Red Standby Doorway Learning (When dip switch Y 5 is ON) When responding to the TEST signal RADAR Detecting ROW 3 Detecting ROW 2 Detecting ROW 1 Detecting Detection row ROW1 ( ROW2 when doorway Learning is turned ON) is detecting door movement Indicates a change of dip switch settings Door Hold is turned ON (When dip switch Y 4 is ON) Internal Sensor Error Reflected infrared signal from the floor is very low 5. SET SAFETY DETECTION AREA Far Near Far 1.0[m] 0.5 0 [4 degree] setting Adjustment screw Near 1.0 [m] 0.5 0 [-8 degree] setting 1.0 1.0 Door 6. SET DESIRED DOOR OPENING DETECTION AREA RADAR Detection Area Adjustment RADAR antenna angle adjustment Installation height "2.2m" with Sensitivity set to "High". 2.0 [m] 1.0 0 1.0 2.0 Installation height "2.2m" with Sensitivity set to "Low". 2.0 [m] 1.0 0 1.0 2.0 Far Near 1.0 2.0 3.0 Separation 15 deg 1.0 30 deg 45 deg 2.0 3.0 Infrared Detection Area Width Adjustment 2.0 (m) 1.0 0 RADAR sensitivity adjustment 1.0 2.0 Door 2.0 2.0 2.2 2.2 3.0 3.0 3.2 3.2 Note: Adjust the depth adjustment lever arm so that the detection area is directly in front of the moving door leaf Put on 1.0 2.0 2.2 3.0 3.2 Narrow Wide 7. DOOR LEARN 8. OTHER USEFUL DIPSWITCH SETTINGS Turning Door Learn ON (Y5), allows the 1st row of detection to be focused inside the door close area without detecting door movement. When Door Learn is turned on, the red LED will blink once, followed by a green blinking LED, which will turn solid green once the door learn process has been completed. Output Radar (Dip Switch: Y3) OFF RADAR + IR rows 2+3 ON 3 3 RADAR [4 degree] setting Door [-8 degree] setting Y OFF 5 Door Y ON 5 Snow Mode (Dip Switch: X5) Adjust sensor frequency settings to prevent cross interference between sensors in close proximity (Dip Switch X3,4 ) Normal 5 A 34 B 34 Snow 5 C 34 D 34 1st row of detection in front of the moving door 1st row of detection inside of the moving door Turn ON/OFF Unidirectional detection (Dip Switch: Y1) OFF 1 ON 1Microsoft Visio 2019