Instructions for Quorum models including: 541-4-80 Juniper 4 Light 32 inch Aged Brass Vanity Light Wall Light, 541-4-80, Juniper 4 Light 32 inch Aged Brass Vanity Light Wall Light, 32 inch Aged Brass Vanity Light Wall Light, Brass Vanity Light Wall Light, Vanity Light Wall Light, Light Wall Light, Wall Light
3 days ago —
20 ore fa — RELATED TO INSTALLATION i. GENERAL. 1.To ensure the success of the installation, be sure to read these instructions carefully before beginning.
File Info : application/pdf, 1 Pages, 470.09KB
DocumentDocumentINSTRUCTIONS 3. Finish lamp installations according to below instructions WIRE CONNECTION DIAGRAM Wires meet safety standards are recommended to connect the supply circuit. CAUTION:FIRE RISK L N CANOPY INSTALLATION INSTRUCTIONS Please read all instructions carefully before you proceed to installmake sure that the power supply is turned off and remains off until installation is completed. Please note that each part is marked with letter as below .Please proceed in an alphabetical order. A. Original electrical box B. Circular bracket C. Screw D.Bracket Screw E. Ground wire F. Terminal cap G. Fixed Screw H. Straight Pipe L. Live wire (black) N. Zero line (white) I. Spiral Pipe 1Remove the nuts and round panels from the wall plate before installing Lamps. Then fix the round shape hanging plate in the screw hole of the installation position with matching screws 2: Screw the two straight Pipes in the attachment on the two exposed Spiral Pipes on the lamp pole respectively, and the lamp head wire passes through the straight Pipe, and then tighten. 3: Align the two straight pipes with the round hole in the wall plate, and fix the straight pipes in the screw hole of the wall plate with nuts and gaskets 4Connect the Lamp's L wire to the live wire of the power supply, connect the N wire to the neutral wire of the power supply, and connect the bare copper wire to the ground wire of the power supply using the wiring cap in the accessory. 5The hanging plate screw is aligned with the small hole on the wall plate, the wall plate is fixed on the round shape hanging plate, and then the nut is screwed on the hanging plate screw and tightened to fix the lamp. 6Remove the lamp holder kit and put on the glass diffuser. Then cover the lamp head with the lamp head kits and screw up to fix the glass diffuser. 7Install the appropriate bulb into the lamp holder and tighten properly to complete the installation. Wiring cap 4 Mounting plate 3 Nut Gasket Wall panel H I 2 1 Screw 5 G Fixed Screw 2 6 Ring A EN L EN L F B D C N L E Accessories List: Straight Pipe 2PCS Nut Gasket Screw Wire connector INSTRUCTIONS 3. Finish lamp installations according to below instructions WIRE CONNECTION DIAGRAM Wires meet safety standards are recommended to connect the supply circuit. CAUTION:FIRE RISK L N CANOPY INSTALLATION INSTRUCTIONS Please read all instructions carefully before you proceed to installmake sure that the power supply is turned off and remains off until installation is completed. Please note that each part is marked with letter as below .Please proceed in an alphabetical order. A. Original electrical box B. Circular bracket C. Screw D.Bracket Screw E. Ground wire F. Terminal cap G. Fixed Screw H. Straight Pipe L. Live wire (black) N. Zero line (white) I. Spiral Pipe 1 Remove the nuts and round panels from the wall plate before installing Lamps. Then fix the round shape hanging plate in the screw hole of the installation position with matching screws 2: Screw the two straight Pipes in the attachment on the two exposed Spiral Pipes on the lamp pole respectively, and the lamp head wire passes through the straight Pipe, and then tighten. 3 Connect the Lamp's L wire to the live wire of the power supply, connect the N wire to the neutral wire of the power supply, and connect the bare copper wire to the ground wire of the power supply using the wiring cap in the accessory. 4: Align the two straight pipes with the circular holes on the wall panel, and then fix the straight pipes in the screw holes on the wall panel with nuts and washers 5 The hanging plate screw is aligned with the small hole on the wall plate, the wall plate is fixed on the round shape hanging plate, and then the nut is screwed on the hanging plate screw and tightened to fix the lamp. 6 Remove the lamp holder kit and put on the glass diffuser. Then cover the lamp head with the lamp head kits and screw up to fix the glass diffuser. 7 Install the appropriate bulb into the lamp holder and tighten properly to complete the installation. Wiring cap 3 Mounting plate 4 Nut Gasket 5 Wall panel HI 2 1 Screw G Fixed Screw A F D B C N L E Accessories List: 2 6 Ring Straight Pipe Nut Gasket Screw Wire connector Instruction 2PCS 2PCS 2PCS 2PCS 3PCS 1 PCS Instruction 2PCS 2PCS 2PCS 3PCS 1 PCS RELATED TO INSTALLATION i. GENERAL 1.To ensure the success of the installation, be sure to read these instructions carefully before beginning. 2.Before installations, prepare the required tools, such as Blade screw driver, Adjustable wrench, Step ladder, Wire cutter. 3,All electrical connections must be in accordance with the National Electrical Code. Qualified licensed electricians are required to conduct the installation of electrical wiring. 4.The outlet box that is connected to the lighting must be directly supported by the building structure. 5.Before starting the installation, disconnect the power to prevent electrical shock. NOTE:The important safeguards and installations appearing in this manual are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense, caution, and care are factors which can not be built into any product. There factors must be applied by the person(s) caring for and operating the fixture. ii.CAUTION 1.Rated 120V/60HZ,bulb 60W maximum. 2.Care should be taken to avoid damage to the surface of lighting and wire, wearing gloves are remmended when installing. 3.Keep lighting away from acid, alkali and other corrosive chemical or gas,clean the lighting with clean soft cloth only. 4.Installation must be carried out by qualified electrician only. 5.Disconnect the power before installing, cleaning and replacing lighting. 6.Never cover the lighting when power is connected. INSTRUCTIONS 1.Take out all lamp parts. The picture below shows the exact items that you receive in this product. Please note that this picture may look different from the computer generate part table. The parts in the part table are not assembled but some parts in this part picture are assembled, so there may be fewer items in the picture than in the table. 2. Part Table Please note: The parts in this table are completely unassembled, for illustrative purpose. In the actual product that you receive, some parts are assembled and attached together. Lock together EN L 1 G White or Ribbed Fixture Wire White Supply Wire Black Fix Wire 1 Black Supply Wire