User Guide for HIKVISION models including: LTK3410FMF, 2A2TG-LTK3410FMF, 2A2TGLTK3410FMF, UD17593N-C, Face Recognition Terminal, UD17593N-C Face Recognition Terminal
LT Security Inc LTK3410FMF Face Recognition Terminal 2A2TG-LTK3410FMF 2A2TGLTK3410FMF ltk3410fmf
1 Appearance microUSB Interface (Use micro USB to USB cable to connect with USB interface) Debugging Port (For debugging only) 22.7 mm 12.3 mm IR Light This scker means"Hot parts! Burned fingers when handling the parts. Wait one-half hour aer switching off before handling parts."It is to indicate that the marked item can be hot and should not be touched without taking care. For device with this scker, this device is intended for installaon in a restricted access locaon, access can only be gained by service persons or by users who have been instructed about the reasons for the restricons applied to the locaon and about any precauons that shall be taken. Camera Camera 83.2 mm White Light IR Light 2 Installaon Installaon Environment: Indoor and outdoor installaon are supported. If installing the device indoors, the device should be at least 2 meters away from the light, and at least 3 meters away from the window or the door. If installing the device outdoors, you should apply Silicone sealant among the cable wiring area to keep the raindrop from entering. The addional force shall be equal to three mes the weight of the equipment but not less than 50N. The equipment and its associated mounng means shall remain secure during the installaon. Aer the installaon, the equipment, including any associated mounng plate, shall not be damaged. Backlight Direct Sunlight Direct Sunlight Indirect Sunlight Close to Light through Window through Window Make sure the gang box is installed on the wall. Align the device with the mounng plate and hang the terminal on the mounng plate. You should purchase the gang box separately. Network Interface Wiring Terminal Tamper The figures are for reference only. 3 Wiring (Normal) Use only power supplies listed in the user instrucons Make sure the power supply is used indoors and the working temperature is between 0 and 40 Screen Mic Card Presenng Area Fingerprint Module (Supported by parts of Device Models) Use 2 supplied screws (SC-K1M4×6-SUS) to secure the base plate on the gang box. Route the cables through the cable hole of the mounng plate, and connect to the corresponding external devices' cables. Use another 4 supplied screws (KA4×22-SUS)to secure the mounng plate on the base plate. Use 1 supplied screw (SC-KM3X6-H2SUS) to secure the device and the mounng plate. Apply Silicone sealant among the joints between the device rear panel and the wall (except the lower side) to keep the raindrop from entering. You can also install the device on the wall or other places without the gang box. For details, refer to the User Manual. After installation, for the proper use of the device (outdoor use), stick the protection film (parts of models supplied) on the screen. NC) COM) NO) When connecng door contact and exit buon, the device and the RS-485 card reader should use the same common ground connecon. The Wiegand terminal here is a Wiegand input terminal. You should set the device's Wiegand direcon to "input". If you should connect to an access controller, you should set the Wiegand direcon to "Output". For details, see the user manual. The suggested external power supply for door lock is 12 V, 1 A The suggested external power supply for Wiegand card reader is 12 V, 1 A For wiring the fire system see the user manul. Do not wire the device to the electric supply directly. If the interface for network connecon is too large, you can use the supplied cable as shown below. The secure door control unit should connect to an external power supply separately. The suggested external power supply is 12 V, 0.5 A. 4 Acvaon Power on and wire the network cable aer installaon you should acvate the device before the first login If the device is not acvated yet, it will enter the Acvate Device page aer powering on. Steps: 1. Create a password and confirm the password. 2. Tap Acvate to acvate the device. For other acvaon methods, see the device user manual. We highly recommend you to create a strong password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case leers, lower case leers, numbers, and special characters) in order to increase the security of your product. And we recommend you change your password regularly, especially in the high security system, changing the password monthly or weekly can beer protect your product. Admin and nimda are not supported to be set as acvaon password. Set Applicaon Mode Aer acvaon you should select an applicaon mode Select Indoor or Others from the drop-down list and tap OK. If you install the device indoors near the window or the face recognion funcon is note working well, select Others. Set Language Select a language from the drop-down list. Set Administrator Steps: 1. Enter the administrator's name and tap Next. 2. Select a credenal to add. You can select face, fingerprint, or card. 3. Tap OK. Tips When Collecng/Comparing Face Picture Posions When Collecng/Comparing Face Picture 1. Use finger to hold the screen surface for 3 s and slide to right/le and enter the acvaon password to enter the Home page. 2. Enter the User Management page, tap + to enter the Add User page. 3. Set the user parameters according to actual needs. Only the device with the fingerprint module support the Expression Keep your expression naturally when collecng or comparing face pictures just like the expression in the picture on the right Recommended Height: 1.43 m to 1.90 m Too High fingerprint related funcons. Do not wear hat, sunglasses, or other accessories that can affect 4. Tap Face and add the face informaon according to the the facial recognion funcon. instrucons. Too Low You can view the captured picture on the screen, Make sure the face Do not make your hair cover your eyes, ears, etc. and heavy 4 picture is in good quality and size. makeup is not allowed. For details about the ps and posions when collecng or comparing the face picture, see the contents on the right. 5. If the picture is in good condion, tap the . Posture 1.4 m 1.4 m Or tap the to take another face picture. In order to get a good quality and accurate face picture posion your face looking at 6. Tap the save icon to save the sengs. the camera when collecng or comparing face picture. Go back to the inial page to start authencaon. For other authencaon methods, see the device user manual. User other authencaon methods if the device is affected by the light or other items. 1:N Matching: The device will compare the captured face picture with the ones in the database. 1:1 Matching: The device will compare the captured face picture with the user linked face picture. Size Make sure your face is in the middle of the collecng window. 0.5 m Too Close 0.5 m Too Far Biometric recognion products are not 100% applicable to an-spoofing environments. If you require a higher security level, use mulple authencaon modes. 1.4 m 1.4 m 0.5 m 1.2 mSerif Affinity Designer 1.8.5 PDFlib PDI 9.1.2p1-i (Win32)