User Manual for RecPro models including: 2BDEK-RP1216, 2BDEKRP1216, rp1216
RecPro. RP1216 Digital Mobile receiver System 2BDEK-RP1216 2BDEKRP1216 rp1216
File Info : application/pdf, 11 Pages, 562.03KB
DocumentDocumentRP-1216 Manual Please read the instruction carefully before operating the unit. ATTENTIONS OF INSTALLATION 1. Please read the instruction manual carefully before installing the unit 2. Make sure to connect other wires before power on the unit. 3. To avoid short circuit. Please make sure all the exposed wires are insulated. 4. Please fix all the wires after installation. 5. Please make connection to the player accordingly to this instruction manual. Wrong connection may cause damage to the unit. 6. This player only fit for 12V DC device INSTALL THE UNIT REMOVE THE UNIT 1. Remove the unit 2. Take out the outer trim frame. HDMI attention: Please use good quality HDMI cable The overall length (front and rear) should not over 12 feet WIRING CONNECTION WIRING CONNECTION 1. This player can only be used by the 12V DC. 2. Do not connect the battery terminal until the player is fully well installation. 3. Please make sure to connect the yellow wire to the positive of the battery(+). 4. When change the fuse. Please make sure the specifications are same. 5. Using good quality speaker with 4-8 ohm can result in the best effect of the equipment. OPERATION LOCATION OF KEYS 1. BAND. 4. 2 INT. 7. DISP. 10. 5 DIR-. 13. LCD DISPLAY. 16. VOL+. 19. RESET. 22. MODE 2. 1 . 3. ZONE1. 5. ZONE2. 6. 3 PRT. 8. 4 RDM. 9. . 11. . 12. 6 DIR+ 14. POWER BUTTON. 15.VOL- 17. AUX in jack. 18. HDMI in PORT. 20. USB PORT. 21. EARPHONE jack OPERATION KEY FUNCTIONS: KEYS ACTION RADIO BAS-TRE-BAL-EQ-L POWER Short OUD-BEEP-P_VOL- /SEL DX-ST Long Power off MODE BAND DISP Short Long Short Long Short Long ZONE 1 Short Long ZONE 2 >>I I<< Short Long Short Long Short Long Change source BT off/link Band change Auto Store Info/Clock Clock setting Zone 1 enable/unable Zone 1 Mute on/off Zone 2 enable/unable Zone 2 Mute on/off Seek up Manual turn up Seek down Manual turn down VOL- Short Long Volume down Volume down fast VOL+ 1/PAU 2/INT Short Long Short Long Short Long Volume up Volume up fast Recall M1 station Save station to M1 Recall M2 station Save station to M2 3/RPT 4/RDM 5/DIR6/DIR+ Short Long Short Long Short Long Short Long Recall M3 station Save station to M3 Recall M4 station Save station to M4 Recall M5 station Save station to M5 Recall M6 station Save station to M6 USB BAS-TRE-BAL-EQ-LO UD-BEEP-P_VOL/ Search: Enter Power off Change source/Search:7 BT off/link Song search / Info/Clock / Search:0 Clock setting Zone 1 enable/unable Zone 1 Mute on/off Zone 2 enable/unable Zone 2 Mute on/off Next file/Search:9 FF Previous file/Search:8 FR Volume down / Search:0-9999 Volume up fast Volume up / Search:0-9999 Volume up fast Play/Pause/Search:1 / INT ON/OFF/Search:2 / RPT(one/fold/all) /Search:3 / RDM on/off / Search:4 / DIR-/Search:5 -10 DIR+/Search:6 +10 AUX IN 1/2 BAS-TRE-BAL-EQLOUD-BEEP-P_VOL Power off Change source BT off/link / / Info/Clock Clock setting Zone 1 enable/unable Zone 1 Mute on/off Zone 2 enable/unable Zone 2 Mute on/off / Reset (5 Seconds) / / Volume down Volume down fast Volume up Volume up fast / Software version / / / / / / / / / / BT MUSIC BAS-TRE-BAL-EQLOUD-BEEPP_VOL Power off Change source BT off/link / / Info/Clock Clock setting Zone 1 enable/unable Zone 1 Mute on/off Zone 2 enable/unable Zone 2 Mute on/off Next file / Previous file / Volume down Volume down fast Volume up Volume up fast / / / / / / / / / / / / OPERATION Basic operation: Turn on/off the unit Press button to turn on the unit. When the unit is switched on, press and hold button for 2 seconds to turn off the unit. Sound and setting adjustment Shortly press knob into the setting menu as below: BASS-TRE-BAL-EQ-LOUD-BEEP-P_VOL-DX-STEREO In each item press VOL+/- button to set them. EQ: To select one of the preset EQ (FLAT/POP/ROCK/CLAS/OFF). LOUD (on/off): Turn on/off the loudness function. BEEP (on/off): Turn on/off the beep sound when the button was pressed. P-VOL (Preset VOL): Setting the power on volume. When the volume that turn off the unit is small than the P-VOL value. Next time turn on the unit it will keep the volume that turn off the unit. When the volume that turn off the unit is large than the P-VOL value. Next time turn on the unit the volume will be back to the P-VOL volume value. DX/LOC (Distance/Local): LOC ON: To reduce the receiving sensitivity when you search station. That means you can receive the station that sound is good. LOC OFF: Don't reduce receiving sensitivity when you search the station. That means you can receive more stations. STEREO/MONO: STEREO: Receiving FM stereo signal. MONO: Change to monochrome. When the signal is not good. Changing it to MONO mode will reduce the noise. Zone1 and Zone 2 operation Press Zone 1 (Zone 2) to make the ZONE 1 (Zone 2) unable/enable. Zone 1 (Zone 2) = enable: Press VOL+/- button can make zone 1 (zone 2) volume up/down. Zone 1 (Zone 2) = unable: Press VOL+/- button can't make zone 1 (zone 2) volume up/down. Press and hold Zone 1 (Zone 2) button for 2 seconds to make zone 1 (zone 2) MUTE on/off. Showing Information/Clock Press DISP button to show the clock or information. Clock setting Press and hold DISP button for 2 seconds. The "HH" will be flashing. Rotating VOL knob to set the hour. Press DISP button the "MM" will be flashing. Rotating VOL knob to set the minute. Then press DISP button to exit. Head phone operation There is a 3.5mm head phone jack in the front panel. It is following the zone 1's volume. OPERATION Radio Operation Receive a radio station Press MODE button to select radio mode. Then press BAND button to select desired band. Shortly press / button to auto seek up/down the desired radio station. Press and hold / button for manual tuning the frequency. Manually store station & recall preset station Receiving a desired station. Press and hold one of the preset button (1~6) for 2 seconds. The current station is stored into the number button. Shortly press the preset button (1~6) to directly listen the station that saved in the corresponding preset button. Auto store station Press and hold BAND button for 2 seconds to auto store stations to numeric buttons 1-6 of band 1~3. USB Operation When an USB driver inserted to the unit, the unit will play the MP3/WMA file automatically. If an USB drive is already inserted in the unit. Keep pressing MODE button shortly until the USB mode display appears. Select file Press / button to skip to next/previous file. Hold / button to fast forward or fast reverse. Play/Pause Press button to pause/playing the file. INTRO playing Press INT button to play first 10 seconds of each file. Press again to stop this function. Repeat function Press RPT button to select RPT mode. RPT FOLD: Repeat all files of the folder. RPT ONE: Repeat the same file. RPT ALL: Repeat all files (default). RANDOM Press RDM button to choose RDM on/off. RDM on: Playing all files in random order. RDM off: Turn off the random function. Directory+/- function Press DIR+/DIR- button to select next/previous folder to play. +10/-10 skip function Press and hold DIR+/DIR- button for 2 seconds to skip +10/-10 files to play. OPERATION Search song Press BAND button. It shows NUM 0000. Rotating VOL (or directly enter number) to select the numbers then press VOL to play. Please note the 7/8/9/0 as: MODE=7, DISP=0. =8, =9, AUX IN 1/2 operation AUX IN 1 for front panel 3.5mm jack. AUX IN 2 for rear RCA connectors. Pressing MODE button to switch to AUX IN 1/2 source when Connected a audio signal to the unit. HDMI operation The front HDMI port is pass through to the rear HDMI port. So any operation will not affect to the HDMI playback. Bluetooth Operation Pairing On mobile phone, select the Bluetooth item searching the Bluetooth device. "BT 105" should appear in the list, select "BT 105" and then input password "0000" If it needs a password. When successful paired, the BT mark will be displayed on LCD. Bluetooth Audio Press MODE button to switch to BT MUSIC mode. It will play a song of your mobile phone automatically. Press key to pause/play the song. Press / button to select next/previous song. Disconnect the Bluetooth When the mobile phone paired with the unit. Press and hold MODE button to disconnect the Bluetooth. Press and hold MODE button again to connect the Bluetooth again. BT APP operation 1. APP installation Using smart phone to control the unit. To install the "DRIVE BT 100" app onto your smart phone. The APP can be downloaded from Google Play (Android phone) or App Store (iPhone). Search for "DRIVE BT 100" and proceed to download. Install per the app instructions. 2. Open the BT function of the smart phone and pair with the "BT 105" and "BT 105APP". 3. Turn on the APP and connect with "BT 105 APP" then it will enter a source. Note: 1) The smart phone must be Bluetooth version 4.0 or above. 2) Before turn on the APP, make sure the unit didn't pair with another device. RADIO mode Auto store station: In FM band clicking button to auto store stations (up to 18 pcs stations). In AM band clicking button to auto store stations (up to 12 pcs stations). Manually store station: Receiving a desired station. Press and hold one of the preset station (1~18) for 2 seconds. The current station is stored into the number. Shortly press the preset station (1~18) to directly listen to this station. OPERATION Radio mode AUX 1/2 mode 1 2 3 USB mode 6 14 4 5 15 BT MUSIC mode 10 11 7 8 12 16 9 13 1: preset station 4: Seek up/down button 7: Zone 1 MUTE 10: refresh button 13: RPT/RDM button 16: pause/play button 2: Auto store button 5: Sub menu 8: Zone 2 MUTE 11: Zone 1 VOL. 14: AUX in 2(HDMI) mode 3: source change 6: Back to previous folder 9: EQ setting 12: Zone 2 VOL. 15: AUX 1 mode OPERATION GENERAL Power Supply Requirements Chassis Dimensions Tone Controls - Bass (at 100 Hz) - Treble (at 10 kHz) Maximum Output Power Current Drain : DC 12 Volts, Negative Ground : 129(W) x 112(D) x 65(H) : ±10 dB : ±10 dB : 4 x 40 watts : 10 Ampere (max.) RADIO Frequency Coverage IF Sensitivity Stereo Separation FM 87.5 to 107.9 MHz 10.7 MHz 4V(S/N=30dB) >25dB AM 530 to 1710 kHz 450 KHz 36dBuV(S/N=20dB) / TROUBLE SHOOTING Symptom No power. Cause The car ignition switch is not on. The fuse is blown. Solution If the power supply is connected to the car accessory circuits, but the engine is not moving, switch the ignition key to "ACC". Replace the fuse. No sound. The operation keys do not work. The radio does not Work. The radio station automatic selection does not work. APP play phone music sound can't send to unit. Volume is in minimum Adjust volume to a desired level. Wiring is not properly connected. Check wiring connection. The built-in microcomputer is not operating properly due to noise. The antenna cable is not connected. The signals are too weak. Press the reset button. Insert the antenna cable firmly. Select a station manually. Unit paired with another mobile phone. 1) Turn off the Bluetooth function of another mobile. 2) Exit APP and turn on APP again. OPERATION FCC Statement: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with minimum distance 20cm between the radiator&your body.EP-02 Adobe PDF Library 11.0