Owner's Manual for PURE DESIGN FITNESS models including: PD-TR8 Treadmill Motor, PD-TR8, Treadmill Motor, Motor
And only one person is allowed to exercise on the treadmill, and overload exercise is strictly prohibited. ... E 6. Explosion-proof impulse protection: the ...
File Info : application/pdf, 32 Pages, 6.50MB
DocumentDocument56Owner's Manual OWNER'S MANUAL Pure Design Fitness Address: 72 South Street Rydalmere NSW 2116 Email: info@puredesignfitness.com.au Ph: 02 9898 1405 ITEM NO.PD-TR8 IMPORTANT SAFETY INSTRUCTIONS Thanks for purchasing this product .The product will help you keep fitter, healthier and better in a very easy way. User Guide 1. Always connect the power plug to a socket with a grounded circuit and the socket must have a special circuit to avoid sharing with other electrical equipment. 2. Ensure the treadmill stable on the ground before use. 3. Check if its function normal or not before running. 4. Stand on two side rails when the treadmill starts 5. Clipped the safety key to your clothes when upcoming to control any emergency. 6. Press the "start" button to get the treadmill started. 7. Follow the running belt with left leg to do preparation before trial run. Only when you feel you can run, you can stand on the treadmill and do it with the right posture. And only one person is allowed to exercise on the treadmill, and overload exercise is strictly prohibited. 8. You can adjust speed if necessary. 9. After running, you can stop the treadmill by pulling out the safety key or pressing the "stop" button. 10. Remember to turn off the power and pull out the plug when you finish exercising. Safety precaution Place the treadmill indoors to avoid any water and no heavy stuff. When using the fitness device, wear comfortable clothing and preferably sports or aerobic shoes. Keep children away from the treadmill to avoid any accident. No overload to give damages to motor, controller, roller and running belt. Make routine maintenance to the treadmill. Keep less indoor dust and a certain extent of humidity to avoid interference of console and controller. Keep the household treadmill continuously running no more than 2 hours. Keep good air circulation when running. There should be 2000x1000mm safe space at the end of treadmill when running Stop running if any discomfort and consult the doctor. Reserve the silicon bottle to some place that children cannot reach, to avoid serious mistake. Prohibit the user jumping off the treadmill directly after use. 2 Pull out the power plug gently from the socket. Stop the machine if anything wrong and cut the power immediately. Ask local distributor to handle any issue or provide service. Dismantle the components personally is not allowed. DANGER! To reduce accidents or harm, please check following rules. Ensure your clothes zipped up before running. Do not wear clothes that easily hooked. Keep power cord away from hot objects. Keep children away from the treadmill. If something wrong , support the handle bar to push up and leave running belt. Do not use the treadmill outdoor. Cut off the power before move of the treadmill . Do not open motor and roller cover unless professionals . This machine can be used under 10A circuit . Ensure that only one person at a time uses the fitness device. The HRC testing may be not as exact as medical devices so its results for reference only . Stop exercising immediately should you feel unwell or if you feel pain in your joints or muscles. In particular, keep an eye on how your body is responding to the exercise program. Dizziness is a sign that you are exercising too intensively with the device. At the first signs of dizziness, lay down on the ground until you feel better. Warning and Prohibit! Following patients under treatment need to get use of the treadmill after approval of professional doctor. 1The person with backache or used to get hurt in the leg ,waist ,neck . Those with numbness of legs, waist, neck and hands ( those with chronic diseases such as intervertebral disc protrusion, spinal slip, cervical vertebra protrusion, etc. ) 2The patient with deformational arthritis , rheumatism or gout . 3The patient with osteroporosis . 4The patient with a bad circulatory system like heart disease ,vascular disorders and vascular hypertension . 5The patient with respirtory disturbance. 6The patient with Artificial heart rhythm problem. 3 7The patient with malignant tumors. 8The patient with thrombosis . 9The patient with diabete-caused perceptual disturbance. 10The person with skin injury . 11The patient with a high fever above 38. 12The person with bent back bone. 13The person with pregnance or in (menstrual) period. 14The person feels discomfortable . 15The person is obviously in a bad condition. 16The person for the purpose of rehabilitation. 17The person having abnormal physical features. - Above cases may cause accident or poor health Stop exercising immediately should you feel unwell like pain in your joints or muscles, dizziness, numb, and abnormal heart beat, and consult the doctor as soon as possible. Keep children away from this product. - Children may get hurt if you ignore this. Told the children that this is not a toy. - Children may get hurt if you ignore this. when using, taking out, putting back or moving this product, please make sure there is nobody or pets around. stop use this product when the cover cracked (inner parts come out) or welded parts drop off. -may cause danger or injury. Do not jump up or down from the treadmill when running. - may fall down and get injury. Do not use or reserve the treadmill outdoor or near bathroom to avoid water. Do not use or reserve the treadmill in the area exposed to direct sunlight, and avoid high temperature places like electric blanket and warmer. - may cause electric leakage or fire. Do not use when the power line or plug damaged, or the socket is loose. - may cause electric shock, short circuit or fire. Do not damage or twist the power cord, also do not put heavy things on it. - may cause fire or electric shock. Only for one person at a time, tell people around not too close. - may fall down and cause injury. people who is not conscious or can't operate by himself can not use the treadmill. 4 - may cause accident or get injury. disassemble, repair, change by customer themselves are forbid absolutely. - may cause mechanical breakdown and injury. To avoid water the main body and operating components can not meet with water or drink. - may cause electric shock and fire. Do not exercise too much if you are not a regular sportspeople. Do not use the treadmill after meals or when feel tired. - may cause damage to your health. This product is for home use. It cannot be used in school or gymnasium where are lots of unspecific users. - may cause injury. Do not use the product while you are having meals or doing other activities. Do not use the product when you feel the body become slow after drink. - may cause accident or injury. Do not use the product when you have hard object in your pocket. - may cause accident or injury. the power plug cannot be attached with needle, waste or water. - may cause electric shock, short circuit and fire. Do not pull out the plug or switch the power to "off" while operating. - may cause injury. Do not operate with wet hands Do not pull out or insert the plug with wet hands. - may cause electric shock or injury. Remember to pull out the plug Remember to pull out the plug when not using. - Dust and dampness can damage insulation and then cause electric leakage and fire. Pull out the plug when maintenance. - may cause electric shock and injury. stop using immediately when the product can not start or have something abnormal, pull out the plug and make a trouble call. - may cause electric shock and injury. pull out the plug when meet with power failure suddenly. - may cause accident and injury when power resumption. 5 You should hold the plug not the wire when pulling out the plug. - may cause short circuit, electric shock and fire. Ground connection instruction the product must have grounded connection. The grounded connection can provide a channel with least resistance for the current when the product is malfunction, thus can reduce the danger of electric shock. The product is equipped with electric wire for grounding conductor and grounding plug. The plug must insert into the socket that conformed to the local regulations. Danger incorrect connection of grounding conductor may cause electric shock.If you are not sure about the grounding connection, please ask a professional electrician to check.if the plug of the product is not match your socket, you should ask for a n electrician to install a correct socket. the product have grounding plug. Please confirm that you have the matched socket first. Socket adapter is not allowed. 6 Exploded diagram 7 87 79 74 80 78 73 77 83 91 75 72 82 84 86 103 88 102 102 102 85 24 76 76 92 102 81 74 92 74 94 78 90 89 62 63 64 101 74 11 23 46 50 14 51 11 22 11 23 40 41 23 59 36 47 38 39 30 9 32 25 15 24 57 33 31 19 1588 2410 57 60 42 19 37 19 60 24 19 26 27 5713 28 44 35 53 43 61 101 17 17 24 17 56 55 55 53 24 55 56 24 56 17 55 24 56 55 17 24 17 56 48 55 24 56 49 2812 28 12 45 102 5 1 102 5 7 5 2 64 3 68 69 70 66 8 67 70 66 68 67 71 71 7 5 346 2 71 71 65 69 100 98 97 9396 101 99 95 16 5434 29 29 34 54 16 105 106 104 18 97 98 52 20 20 18 20 20 Exploded chart list No. Description 1 Base weldment 2 Hexagon large flat head half-tooth bolt 3 hexagon lock nut 4 flat washer Size M8×50×20 M8 8 5 Tapered foot pad (OMA-05-07-005) 6 wheel 50×41×17×M8×27 62×8.0×t22 7 Curved open pipe plug 40×60×t2.0 8 Main frame weldment 9 Motor mount (1320CA-06) 10 Motor cover plate 11 fixed tube of motor cover 16×t1.2×23 12 Hexagon cylindrical head full tooth bolt 13 Hexagon cylindrical head full tooth bolt M8×75 M8×60 14 Hexagon cylindrical head full tooth bolt M8×15 15 Hexagon large flat head M8×15 full tooth bolt 16 Hexagon large flat head M8×45×20 half-tooth bolt 17 Hexagon countersunk head full tooth bolt M6×30×16 18 Cross recessed large flat head full tooth bolt M5×10 19 Cross recessed large flat head full tooth bolt M4×10 20 Cross recessed large ST4×16 flat head tapping screw 21 Cross recessed large ST4×10 flat head tapping screw 22 Cross recessed pan head tapping screw ST3×10 QTY No. Description 1 63 Upright post R welds 2 64 communication line 2 65 Lift frame welds 2 66 Hexagon head half-tooth bolt 4 67 Hexagon large flat head full tooth bolt 2 68 Powder metallurgy sleeve 2 69 Sleeve 1 70 flat washer 1 71 Lifting shaft sleeve (OMA-05-06-023) 1 72 Console holder welds 1 73 Display frame Size 0.32 SM4PIN/SM4PIN/L-12 00mm/26# M12×14×35×19 QTY 1 1 1 2 M10×25×15 2 24×19×14×14×3 2 25×18×t3.0 2 14 2 25×17×10×6×1 4 1 498×175×10.1 1 1 74 Cross recessed large ST4×16 19 flat head tapping screw 2 75 Cross recessed ST4×15 4 countersunk head tapping screw 2 76 Cross recessed ST4×70 2 countersunk head tapping screw 1 77 keratoscopic arc t0.5×490×167 1 2 78 Cross recessed large ST4×10 12 flat head tapping screw 4 79 Panel 1136EA/571×277×10. 1 8 2 80 Panel rear cover 1136EA/571×277×28 1 6 81 console basket upper 1 cover 4 82 console basket lower 1 cover 7 83 Anti-slip pad 1 4 84 speed hand-held 7239EA/SM5PIN/L-50 1 heartbeat components MM/SPEED+/- 23 Cross recessed countersunk head tapping screw 24 Console frame welds ST4×15 2 85 incline hand-held 7239EA/L-50MM/SM5 1 heartbeat components PIN/INCLINE+/- 1 86 communication line SM4PIN/SM4PIN/L-75 1 0mm/26# 25 spring washer 8 26 spring washer 5 27 serrated lock washers 5 28 flat washer 8 29 hexagon lock nut M8 3 87 3338EA console set 1 17 88 Hand-held heartbeat 3330EA/L-1000mm 1 communication wire 2 89 Safety key J52×15×15/L-700 1 3 90 Safety lock socket J86×20×16 1 3 91 Acrylic panel t1.0×554×260 1 8 30 Hexagon large flat head M10×35×20 3 92 D shaped tube plug DX40×80 2 half-tooth bolt 31 Hexagon large flat head M10×65×20 half-tooth bolt 2 93 one-way valve 29×t1.2×340 1 32 Hexagon large flat head M10 1 94 miscellaneous basket 1 half-tooth bolt cover 33 flat washer 10 1 95 Hexagon large flat M8×30×20 1 head half-tooth bolt 34 flat washer 8 1 96 Double round tube plug 33×23×48 1 35 communication line SM5PIN/SM4PIN/L-75 1 97 hexagon lock nut M8 2 0mm/26#/ 36 photoelectric sensor L-500 2 98 flat washer 88×50×17×606 2 37 3330EA controller ERP AC220V/1-20KM/H/Incl 1 ine(ERP) 99 Pressure rod 720×318×10×8.2× 1 350N 38 Connect wire L-300mm/1.5mm2/(Re d) 1 100 shrapnel-1 t0.6×16.5×43 1 39 Connect wire L-300mm/1.5mm2/(Bla 1 101 Hexagon large flat ck) head half-tooth bolt M8×50×20 4 40 Rocker switch KCD4 1 102 Hexagon large flat head full tooth bolt M8×15 8 41 Self-resetting switch 10A/ABR21-16/250VA 1 103 Hexagon pan head full M6×10 4 C tooth bolt 42 Connect wire L-100mm/1.5mm2/(Re 1 104 L-shaped wrench 4*30*80 1 d) 43 Plug 3×1.0mm2×2000 1 105 L-shaped wrench 6*35*80 1 44 3330EA front roller 45 3330EA rear roller 88×50×17×606 50×17×529×578 1 106 T-shaped wrench 1 6*80 1 46 Motor 47 Incline motor 48 3330EA running deck 49 Running belt 50 belt 51 3330EA motor cover 52 Rear cover 53 Side rail 54 Wheel 55 Cylindrical cushion 56 Round guide block 57 pipe strap 58 EVA pad (E21-V1-12) 59 magnet ring 60 cable clamp 61 power cable clip 62 Upright post L welds 1.5HP/DC180V/4600R 1 PM/32/36 1/18HP/75mm/AC220 1 V(195mm) 1300×604×t18 1 2930×500×t1.6 1 174442PJ6 1 367.5×673×36.7 1 673×93×51 1 87×34.5×1342 2 62×8.0×t22 2 30×30×M6×6 6 25×5×4.5 10 16white 3 t15×30×30 1 29×17×t7.5 1 3/8(UC-2) 1 SR-5R1 1 0.32 1 9 Product introduction Console Upright post Motor cover Handle bar Safety key Running belt Side rail Rear cover Technical information Dimension Running surface Speed Fold: 1135*795*1460 Unfold: 1720*835*1440 1420*500 1.020.0km/h RemarkWE RESERVE THE RIGHT TO AMEND THE PRODUCT WITHOUT PRIOR NOTICE. 10 Packing list Main body Console Upright post Console frame Safety key 11 silicone oil Manual Manual Hardware Pack List Screwkit Screw kit Hexagon large flat head half tooth boltM8*50*20 4pcs L shape wrench S4 1pc Hexagon pan head full tooth boltM6*104pcs L-type Allen wrench S6 1pc Hexagon large flat head full tooth bolt M8×15 8pcs T-shaped wrench 6×80 12 Installation Steps Notes:Please don't totally tighten all screws during installation. Tighten all bolts after the components are fully installed. Step 1: Lift the machine out of the packing box and place it on the flat floor. (as shown in the picture), remove all PE bags and packing belts wrapped on the machine! 62 102 102 63 1 101 101 Step 2: As shown :Keep the treadmill upright, insert the (62) upright post into the corresponding position of the (1) base solder, lock it into the corresponding hole of the (62) upright post with the (101) M8×50×20 hexagonal large flat head half-tooth bolt through the (1) base, and lock it into the corresponding hole of the (01) base with the (102) M8*15 hexagonal large flat head half-tooth bolt through the (62)upright post. The operation on the other side (63) is the same after connecting the upright post (please be careful, don't clamp the communication line in the upright post). 13 24 102 102 102 102 63 62 Step 3: As shown in the figure: After the signal line on the right side of the handrail frame is connected, install the (72) handrail to the corresponding position of the (62) (63) upright post, and lock the (72) handrail frame through the corresponding hole of the (62) (63) upright post with the (102) M8×15 hexagonal large flat head full-tooth bolt. 103 72 24 14 Step 4: As shown: after connecting the signal wire of the console, insert the welding fixed mount (72) into the armrest welding holder(24), locked with (103)M6×10 . 89 Step 5: Set up the machine and tighten all self-mounting bolts. Then put the safety lock (89), the treadmill is completed! 15 General Fitness Tips 1. Warm-up Do not hold your breath before warming up for 5-10 minutes before each warm-up. 2. Breathe Usually when you are preparing to restore your breath, inhale with your nose and spit out your breath with your mouth. The breathing and movement should be coordinated, such as breathing too fast. The movement should be stopped immediately 3. Frequency The same part of the muscle should have a rest of 48 hours, that is, the same part can only be trained every other day. 4. Load According to the individual physical condition determine the amount of training, then according to the principle of asymptotic load to practice, the initial training of muscle soreness is a normal phenomenon, as long as continue to practice, soreness can be eliminated. 5. Relax Do 5 minutes of exercise after each exercise, especially the stretching and relaxation of the muscles of the foot, to avoid long-term muscle condensation, maintain a muscle flexible diet 6. Diet In order to protect the digestive system, one hour after meals before exercise, training should be at least half an hour before eating, exercise less water, especially drinking water, so as not to increase the heart, kidney burden Stretching exercises No matter how fast you walk, it's best to do stretching exercises first. Warm muscles are easier to stretch, so take a 5-10 minute warm-up. Then stop and do the stretching as follows: 5 times, each step for 10 seconds or more; do it again after the workout. 1.Stretch down The knees are slightly curved, the body slowly bends forward, let the back and shoulders relax, and the hands try to touch the toes. Keep it for 10~15 seconds, then relax. Repeat 3 times (As picture 1 shown). 2. Tendon stretching Sit on a clean seat cushion and straighten one leg. Put the other leg inward so that it fits snugly against the inside of the straight leg. Try to touch the toes with your hands. Keep it for 10~15 seconds, then relax. Repeat 3 times for each leg (As picture 2 shown). 3. Calf and heel stretch Hold the wall or tree with both hands and one foot behind. Keep your hind legs upright and your heels on the ground, leaning in the direction of the wall or tree. Keep it for 10~15 seconds, then relax. Repeat 3 times for each leg (As picture 3 shown). 4. Quadriceps stretching Grasp the balance with your left hand or the table, then extend your right hand backwards and grab your right ankle and slowly pull it toward your hips until you feel the muscles in front of your thighs are tense. Keep it for 10~15 seconds, then relax. Repeat 3 times for each leg (As picture 4 shown). 5. The sartorius muscle (muscle inside the thigh) stretches The soles of the feet are opposite and the knees sit down. Grasp your feet with both hands and pull them in the direction of the groin. Keep it for 10~15 seconds, then relax. Repeat 3 times. (As picture 5 shown). 16 Instructions of Console Panel LED display Incline shortcuts incline"+""-" Program Start/Pause Mode Speed shortcuts Speed"+""-" Console Function Description 1P01 is a user manual program, P01-P36 is a built-in automatic training program, 3 user, BMI; 2LED display, 14 operation keys; 3Speed, distance system conversion function; 4Operating speed range: KM 1.0~20.0KM/H, inch 0.6-12.5MPH; 5Incline range: 0~15%; 6Overload, overcurrent protection, explosion-proof impact, anti-speed, anti-electromagnetic interference and other safety protection functions; 7System self-test, abnormal information prompt function; 83 custom functions; 9ERP functions; 10Fuel reminder function; Description of windows 1"CALORIES" window: display the value of Calories; 2"TIME" window: display the value of time; 3"DISTANCE" window: display the value of distance; 4"INCLINE" window: shows the value of incline. 5"PULSE" window: display the value of heart rate; 6"SPEED" window: shows the speed value; 17 Imperial Conversion Instructions: 1) After unplugging the safety lock, press the "PROGRAM" and "MODE" keys at the same time, the display will show 0.6, which means the conversion from kilometers to miles; 2) After unplugging the safety lock, press the "PROGRAM" and "MODE" keys at the same time, the display will display 1.0, indicating that miles are converted to kilometers; KEY FUNCTION 1 "PROG" : program selection key, in the stopped state, cycle to select program P0~P36, U01~U03, BMI; 2"MODE" : When the manual MODE is selected, the initial state is the normal mode. Press the mode key to select the countdown mode -> Backward distance mode -> Backward calories -> Normal mode in the manual mode; Reset button for the default (30 minutes) countdown interval in P1-P36; 3"START" : start/pause button, in the stopped state, start the treadmill; In the running state, suspend the treadmill; "pause" without effect if the Bluetooth connection; 4STOP: Stop/reset key 1. In the running state, press the STOP key for slow stop; 2. When the ERR information is displayed, the information displayed once is cleared. 5"+" : speed increment key, in the stop or fat measurement state, to set the parameter increment key, in the running state, to speed increment key; 6"-" : speed decline key, in the stop or fat measurement state, is the set parameter decline key, in the running state, is the speed decline key; 7"QUICK SPEED" : 3,6,9 speed shortcut keys, in the running state of the treadmill, directly set the speed to the specified value of the key; 8" " : incline increment key; 9 " " : incline decline key; 10"QUICK INCLINE" : 3,6,9 incline shortcut keys, when the treadmill is running, directly set the speed to the specified value of the key; Safety key The safety key is composed of a touch switch, a clothespin and a nylon rope, which can prevent the emergency shutdown. In any state, as long as the safety lock is out of position, the treadmill stops running, the console keyboard is forbidden to operate, and the screen displays "E-07", accompanied by a prompt sound. Each time you place the security lock, the screen will display for 2 seconds and then enter the default working state of the system. USER program: USER has three USER1~USER3. In USER mode, users can access or set their own sports program, press 18 "PROG" key to adjust to "USER1~USER3", then press "mode" key to set or press START key to start sports. Press the "MODE" key to set the 10 sections of speed and ascension of your own program. After setting, the user press "START" to start the treadmill. The user's program will be saved and can be used directly next time. Safety Guide 1 Insert the power cord plug into the 10A power socket with safety ground, turn on the power switch, the console screen is fully displayed with a prompt sound, then identify the safety key. 2 Place the safety key in the position on the console and clip the clothespin to the clothes on the chest. The screen is fully displayed for 2 seconds then enters the default working state: all counters are cleared to zero, the set value is reset, the treadmill is in the positive timing mode of manual program P0; 3 Press "PROG" key to select a program: P01~P36, U01,U02,U03, BMI; 4 "P0" is a user-defined program, press "MODE" key to select four training modes, the training speed and slope are set by the user. Default: Speed 1.0KM/H, slope 0 section. Training mode 1: positive counting time, time, distance, calories are positive counting, close the setting function; Training mode 2: countdown time, setup state, time window flashing, press "+", "-" key to modify the set value, set range: 5-99 minutes, default value: 30:00; Training mode 3: countdown distance, set the state, the distance window flashes, press "", "-" key to modify the set value, set the range: 1.0-99.0 KM, the default value: 1KM; Training mode 4: reverse calorie, set state, calorie window flashes, press "", "-" key to modify the set value, set range: 20-990CAL, default value: 50CAL; 5 "P01-P36" for the system setup program, only trained in the countdown mode, under the setting state, the time window flashes, press "", "-" key to modify the set value, press the "MODE" key to reset to the default value, set the range: 5-99MIN, the default value: 30:00; 6After setting the training mode, press "START" key, the screen starts to display 5 seconds countdown with 5 beeps, after the countdown is 1, the treadmill starts gently, accelerates slowly to the displayed speed, and then runs smoothly at constant speed. 7In the running state, press "", "-" key or "QUICK SPEED" key to adjust the speed of the treadmill; 8 In P1-P36, the speed of each program is divided into 10 segments, each period is equally divided according to the set time. The speed adjusted by key is only valid in the current segment, and three beeps will be sent three seconds in advance when the segment is converted to the other segment. The motor stops automatically when the program runs full of 10 segments, with a "beep"; 9In running mode, press "START" key, the motor will change between the two states of suspension and running. Restart in the paused state, the recorded running data and process stay the same. 10In the motor running, press "STOP" key, the motor will slow down until it stops smoothly, all the settings will be restored to the default state; 11In the motor running, press " "," "key or" QUICK INCLINE "to adjust the treadmill slope; 12In any state, pull off the safety lock, the screen displays "E-07", and accompanied by a tone, the treadmill stops running; 19 13 The control system at any time in the safety monitoring, as long as the discovery of anomalies, the treadmill will be emergency stopped, the screen displays abnormal information prompts, accompanied by beeps; 14 When the abnormal information is displayed on the screen, press STOP. The system clears the displayed information one time. 15BMI test method: press the "PROG" key to select the program BMI, press the "MODE" key to select the project serial number. press the "" and "-" keys to set the parameters. 16Item No. F1 (Sex): indicates the gender; set the parameter range: 1-2, "1" indicates male, "2" indicates female, default value: 1; 17Item No. F2 (Age): indicates age; set parameter range: 1-99 years old, default value: 25 years old. 18Item No. F3 (Height): indicates height; set parameter range: 100-220CM, default value: 170CM; 19Item serial number F4 (Weight): indicates weight; set parameter range: 20-150KG, default value: 70KG; 20 Item serial number F5 (BMI): indicates the completion of parameter settings, enter the BMI test state, please hold both hands to the left and right handles of the heart rate sensing piece, wait for 4 seconds, the parameter display window will show the test person's body fat rate (BMI); to the standard of the Asian people, the body fat is less than 18 for thin, between 18 and 24 for the ideal body weight, between 25 and 28 for overweight, greater than 29 for obese, and the body fat of the person under test will be shown in the window. Default value: 24 (this data is only for exercise reference). 21British BMI test method: Press the "PROG" key to select program BMI, press the "MODE" key to select item serial number, press the "+" and "-" keys to set parameters. A) Item number F1 (Sexo) : indicates gender; The value ranges from 1 to 2, where 1 indicates male and 2 indicates female. The default value is 1. B) Item number F2 (Age) : indicates age; Value range: 1 to 99 years old. Default value: 25 years old ; C) Item No. F3 (Height) : indicates height. The value ranges from 39 to 87 inches. Default value: 67 inches. D) Item number F4 (Weight) : indicates weight; Set parameters range: 44-330 LBS. Default: 154 LBS. E) Item No. F5 (BMI) : indicates the completion of parameter setting and entering the body fat test state. Please hold both hands on the heart rate sensor on the left and right handles.Wait 4 seconds, the parameter display window will display the body fat percentage (BMI) of the tested person; By Asian standards, a body fat of less than 18 is considered lean, a body fat of 18 to 24 is considered ideal, a body fat of 25 to 28 is overweight, and a body fat of more than 29 is considered obese (this data is for exercise reference only). Default value: 24 ERP transfer function: The system starts in ERP mode by default. When the treadmill is not operated, it will enter hibernation state in about 4 and a half minutes to save power consumption. Press any key to wake up the system. In standby MODE, hold down the mode key for 3S to display '2222' to cancel the ERP function, and hold down the mode key for 3S to display '1111' to return to ERP mode. 20 Speed and slope table for the automatic program P01-P36: metric Seg 1 Pro Class P1 SPEED 1.0 INCLINE 2 P2 SPEED 2.0 INCLINE 3 P3 SPEED 2.0 INCLINE 1 P4 SPEED 2.0 INCLINE 3 P5 SPEED 3.0 INCLINE 2 P6 SPEED 3.0 INCLINE 1 P7 SPEED 3.0 INCLINE 1 P8 SPEED 3.0 INCLINE 3 P9 SPEED 3.0 INCLINE 3 P10 SPEED 3.0 INCLINE 2 P11 SPEED 4.0 INCLINE 1 P12 SPEED 4.0 INCLINE 3 P13 SPEED 2.0 INCLINE 3 P14 SPEED 3.0 INCLINE 4 P15 SPEED 3.0 INCLINE 2 P16 SPEED 3.0 INCLINE 4 P17 SPEED 4.0 INCLINE 3 P18 SPEED 4.0 INCLINE 2 P19 SPEED 4.0 INCLINE 2.0 P20 SPEED 4.0 INCLINE 4 P21 SPEED 4.0 2 3 4 5 6 7 8 9 10 3.0 5.0 5.0 5.0 7.0 7.0 5.0 3.0 2.0 2 8 6 6 4 4 6 2 2 3.0 5.0 8.0 5.0 5.0 6.0 8.0 4.0 3.0 3 2 2 8 8 4 4 4 4 3.0 7.0 8.0 5.0 5.0 5.0 8.0 4.0 3.0 2 5 7 7 4 4 6 2 2 2.0 5.0 8.0 8.0 8.0 8.0 5.0 3.0 2.0 3 9 9 9 9 9 6 2 2 4.0 8.0 9.0 10.0 10.0 10.0 7.0 4.0 3.0 2 8 6 6 6 6 6 1 1 4.0 6.0 7.0 7.0 7.0 9.0 10.0 5.0 3.0 8 8 7 7 7 7 5 3 1 4.0 4.0 10.0 4.0 9.0 4.0 11.0 3.0 2.0 1 6 6 6 8 8 10 6 2 5.0 7.0 9.0 3.0 5.0 7.0 5.0 11.0 5.0 3 3 7 7 3 3 3 5 5 7.0 10.0 4.0 7.0 11.0 5.0 4.0 12.0 6.0 6 7 3 8 8 3 8 4 4 5.0 9.0 10.0 6.0 6.0 9.0 6.0 11.0 3.0 7 5 5 8 8 8 8 4 4 5.0 11.0 9.0 6.0 8.0 9.0 11.0 6.0 5.0 6 3 3 7 7 4 4 6 6 6.0 10.0 10.0 10.0 7.0 7.0 10.0 6.0 5.0 8 9 5 5 8 8 4 4 4 4.0 6.0 6.0 6.0 8.0 8.0 6.0 4.0 3.0 3 9 7 7 5 5 7 3 3 4.0 6.0 9.0 6.0 6.0 7.0 9.0 5.0 4.0 4 3 3 9 9 5 5 5 5 4.0 8.0 9.0 6.0 6.0 6.0 9.0 5.0 4.0 3 6 8 8 5 5 7 3 3 3.0 6.0 9.0 9.0 9.0 9.0 6.0 4.0 3.0 4 10 10 10 10 10 7 3 3 5.0 9.0 10.0 11.0 11.0 11.0 8.0 5.0 4.0 3 9 7 7 7 7 7 2 2 5.0 7.0 8.0 8.0 8.0 10.0 11.0 6.0 4.0 9 9 8 8 8 8 6 4 2 5.0 5.0 11.0 5.0 10.0 5.0 12.0 4.0 3.0 2 7 7 7 9 9 11 7 3 6.0 8.0 10.0 4.0 6.0 8.0 6.0 12.0 6.0 4 4 8 8 4 4 4 6 6 8.0 11.0 5.0 8.0 12.0 6.0 5.0 12.0 7.0 21 INCLINE 4 P22 SPEED 4.0 INCLINE 3 P23 SPEED 5.0 INCLINE 2 P24 SPEED 5.0 INCLINE 4 P25 SPEED 3.0 INCLINE 4 P26 SPEED 4.0 INCLINE 5 P27 SPEED 4.0 INCLINE 3 P28 SPEED 4.0 INCLINE 5 P29 SPEED 5.0 INCLINE 4 P30 SPEED 5.0 INCLINE 3 P31 SPEED 5.0 INCLINE 3 P32 SPEED 5.0 INCLINE 5 P33 SPEED 5.0 INCLINE 5 P34 SPEED 5.0 INCLINE 4 P35 SPEED 6.0 INCLINE 3 P36 SPEED 6.0 INCLINE 5 7 8 4 9 9 4 9 5 5 6.0 10.0 11.0 7.0 7.0 10.0 7.0 12.0 4.0 8 6 6 9 9 9 9 5 5 6.0 12.0 10.0 7.0 9.0 10.0 12.0 7.0 6.0 7 4 4 8 8 5 5 7 7 7.0 11.0 11.0 11.0 8.0 8.0 11.0 7.0 6.0 9 10 6 6 9 9 5 5 5 5.0 7.0 7.0 7.0 9.0 9.0 7.0 5.0 4.0 4 10 8 8 6 6 8 4 4 5.0 7.0 10.0 7.0 7.0 8.0 10.0 6.0 5.0 5 4 4 10 10 6 6 6 6 5.0 9.0 10.0 7.0 7.0 7.0 10.0 6.0 5.0 4 7 9 9 6 6 8 4 4 4.0 7.0 10.0 10.0 10.0 10.0 7.0 5.0 4.0 5 10 10 10 10 10 8 4 4 6.0 10.0 11.0 12.0 12.0 12.0 9.0 6.0 5.0 4 10 8 8 8 8 8 3 3 6.0 8.0 9.0 9.0 9.0 11.0 12.0 7.0 5.0 10 10 9 9 9 9 7 5 3 6.0 6.0 12.0 6.0 11.0 6.0 12.0 5.0 4.0 3 8 8 8 10 10 10 8 4 7.0 9.0 11.0 5.0 7.0 9.0 7.0 12.0 7.0 5 5 9 9 5 5 5 7 7 9.0 12.0 6.0 9.0 12.0 7.0 6.0 12.0 8.0 8 9 5 10 10 5 10 6 6 7.0 11.0 12.0 8.0 8.0 11.0 8.0 12.0 5.0 9 7 7 10 10 10 10 6 6 7.0 12.0 11.0 8.0 10.0 11.0 12.0 8.0 7.0 8 5 5 9 9 6 6 8 8 8.0 12.0 12.0 12.0 9.0 9.0 12.0 8.0 7.0 10 10 7 7 10 10 6 6 6 22 Speed and slope table for the automatic program P01-P36: inch Seg Pro Class P1 SPEED INCLINE P2 SPEED INCLINE P3 SPEED INCLINE P4 SPEED INCLINE P5 SPEED INCLINE P6 SPEED INCLINE P7 SPEED INCLINE P8 SPEED INCLINE P9 SPEED INCLINE P10 SPEED INCLINE P11 SPEED INCLINE P12 SPEED INCLINE P13 SPEED INCLINE P14 SPEED INCLINE P15 SPEED INCLINE P16 SPEED INCLINE P17 SPEED INCLINE P18 SPEED INCLINE P19 SPEED INCLINE P20 SPEED 1 2 3 4 5 6 7 8 9 10 0.6 1.8 3.1 3.1 3.1 4.3 4.3 3.1 1.8 1.2 2 2 8 6 6 4 4 6 2 2 1.2 1.8 3.1 5 3.1 3.1 3.7 5 2.5 1.8 3 3 2 2 8 8 4 4 4 4 1.2 1.8 4.3 5 3.1 3.1 3.1 5 2.5 1.8 1 2 5 7 7 4 4 6 2 2 1.2 1.2 3.1 5 5 5 5.0 3.1 1.8 1.2 3 3 9 9 9 9 9 6 2 2 1.8 2.5 5 5.6 6.2 6.2 6.2 4.3 2.5 1.8 2 2 8 6 6 6 6 6 1 1 1.8 2.5 3.7 4.3 4.3 4.3 5.6 6.2 3.1 1.8 1 8 8 7 7 7 7 5 3 1 1.8 2.5 2.5 6.2 2.5 5.6 2.5 6.8 1.8 1.2 1 1 6 6 6 8 8 10 6 2 1.8 3.1 4.3 5.6 1.8 3.1 4.3 3.1 6.8 3.1 3 3 3 7 7 3 3 3 5 5 1.8 4.3 6.2 2.5 4.3 6.8 3.1 2.5 7.5 3.7 3 6 7 3 8 8 3 8 4 4 1.8 3.1 5.6 6.2 3.7 3.7 5.6 3.7 6.8 1.8 2 7 5 5 8 8 8 8 4 4 2.5 3.1 6.8 5.6 3.7 5 5.6 6.8 3.7 3.1 1 6 3 3 7 7 4 4 6 6 2.5 3.7 6.2 6.2 6.2 4.3 4.3 6.2 3.7 3.1 3 8 9 5 5 8 8 4 4 4 1.2 2.5 3.7 3.7 3.7 5 5 3.7 2.5 1.8 3 3 9 7 7 5 5 7 3 3 1.8 2.5 3.7 5.6 3.7 3.7 4.3 5.6 3.1 2.5 4 4 3 3 9 9 5 5 5 5 1.8 2.5 5 5.6 3.7 3.7 3.7 5.6 3.1 2.5 2 3 6 8 8 5 5 7 3 3 1.8 1.8 3.7 5.6 5.6 5.6 5.6 3.7 2.5 1.8 4 4 10 10 10 10 10 7 3 3 2.5 3.1 5.6 6.2 6.8 6.8 6.8 5 3.1 2.5 3 3 9 7 7 7 7 7 2 2 2.5 3.1 4.3 5 5 5 6.2 6.8 3.7 2.5 2 9 9 8 8 8 8 6 4 2 2.5 3.1 3.1 6.8 3.1 6.2 3.1 7.5 2.5 1.8 2 2 7 7 7 9 9 11 7 3 2.5 3.7 5 6.2 2.5 3.7 5 3.7 7.5 3.7 23 INCLINE 4 4 4 8 8 4 4 4 6 6 P21 SPEED 2.5 5 6.8 3.1 5 7.5 3.7 3.1 7.5 4.3 INCLINE 4 7 8 4 9 9 4 9 5 5 P22 SPEED 2.5 3.7 6.2 6.8 4.3 4.3 6.2 4.3 7.5 2.5 INCLINE 3 8 6 6 9 9 9 9 5 5 P23 SPEED 3.1 3.7 7.5 6.2 4.3 5.6 6.2 7.5 4.3 3.7 INCLINE 2 7 4 4 8 8 5 5 7 7 P24 SPEED 3.1 4.3 6.8 6.8 6.8 5 5 6.8 4.3 3.7 INCLINE 4 9 10 6 6 9 9 5 5 5 P25 SPEED 1.8 3.1 4.3 4.3 4.3 5.6 5.6 4.3 3.1 2.5 INCLINE 4 4 10 8 8 6 6 8 4 4 P26 SPEED 2.5 3.1 4.3 6.2 4.3 4.3 5 6.2 3.7 3.1 INCLINE 5 5 4 4 10 10 6 6 6 6 P27 SPEED 2.5 3.1 5.6 6.2 4.3 4.3 4.3 6.2 3.7 3.1 INCLINE 3 4 7 9 9 6 6 8 4 4 P28 SPEED 2.5 2.5 4.3 6.2 6.2 6.2 6.2 4.3 3.1 2.5 INCLINE 5 5 10 10 10 10 10 8 4 4 P29 SPEED 3.1 3.7 6.2 6.8 7.5 7.5 7.5 5.6 3.7 3.1 INCLINE 4 4 10 8 8 8 8 8 3 3 P30 SPEED 3.1 3.7 5 5.6 5.6 5.6 6.8 7.5 4.3 3.1 INCLINE 3 10 10 9 9 9 9 7 5 3 P31 SPEED 3.1 3.7 3.7 7.5 3.7 6.8 3.7 7.5 3.1 2.5 INCLINE 3 3 8 8 8 10 10 10 8 4 P32 SPEED 3.1 4.3 5.6 6.8 3.1 4.3 5.6 4.3 7.5 4.3 INCLINE 5 5 5 9 9 5 5 5 7 7 P33 SPEED 3.1 5.6 7.5 3.7 5.6 7.5 4.3 3.7 7.5 5 INCLINE 5 8 9 5 10 10 5 10 6 6 P34 SPEED 3.1 4.3 6.8 7.5 5 5 6.8 5 7.5 3.1 INCLINE 4 9 7 7 10 10 10 10 6 6 P35 SPEED 3.7 4.3 7.5 6.8 5 6.2 6.8 7.5 5 4.3 INCLINE 3 8 5 5 9 9 6 6 8 8 P36 SPEED 3.7 5 7.5 7.5 7.5 5.6 5.6 7.5 5 4.3 INCLINE 5 10 10 7 7 10 10 6 6 6 24 Common faults and troubleshooting methods Porblem code Possible reasons Solution System does not work AThe power is not connected or the power is not turned on BSafety locks are not in place CThe controller or console is not powered on Connect the power supply, or turn the power switch to the "NO" position Put the safety lock in the correct position Replace the controller or console DPoor line contact Check system input and output and communication lines Suddenly ASafety lock dropped stop in normal Bsystem error condition Keys failure KEY INVALID E-01 AThe communication cable is in poor contact BDefective console Reinstall the safety lock Ask the repairman to deal with it 1Replace the key board and keyboard cable 2, replace the motherboard 3, replace the console Reconnect the communication cable and check whether the port is properly inserted or replace the communication cable. Change the console CDefective controller Change the controller ADefective Motor cable and motor Change the motor E-02 E-03 BThe motor cable is improperly connected to the controller or the Check and reconnect or replace the controller controller is improperly connected AThe photoelectric sensor is not installed correctly Check and reconnect BPoor photoelectric sensor Replacement of photosensor CPhotoelectric first contact sensor dirty or poor Check and reconnect/clean light sensor DDefective controller Change the controller AController damaged Replace the controller E-05 BMotor damaged Replace the motor Cmechanical failure Check the running oil or drum for blockage E-07 The console is not detecting the safety lock signal 1check whether the safety lock is put in place; 3. Reinstall the safety lock mechanism; 3. Replace the electronic watch AThe grip wire is not inserted in No heart place or the grip wire is not good rate BElectronic system circuit fault Check and connect or replace the grip cable Change the console console incomplete ALED digital tube or screen is bad Replace the mainboard or screen or missing lines Bsystem failure Change the console 25 Folding and Moving of Treadmill 1 Folding Treadmill 1) When folding, the power must be disconnected. 2) Check the incline of the treadmill for the lowest position. 3) Lift the treadmill to the upright position, the Ezfit linking parts automatically get stuck on the hydraulic; 4) Check whether the check Ezfit linking parts is stuck on the hydraulic, as shown in the figure. 2 Treadmill unfolds 1) To unfold the treadmill, you need to choose a place about 1 meter away from the power outlet and the ground is flat without other obstacles. 2) When unfolding the treadmill, firstly, you need to hold the treadmill with both hands, step on the Ezfit linking with your feet, and the treadmill will automatically drop to the ground slowly; at this time, the user must leave the treadmill about 1 meter away until the treadmill is completely Expand. as the picture shows: 3 Moving Treadmill When moving, must ensure that: 1) The power switch of the treadmill is turned off; 2) The power plug has been pulled out from the socket; 3) The large frame has been folded; After clarifying the above points, hold the end of the treadmill with one hand and the armrest on the same side with the other hand, and move the machine slowly when it is tilted 40~50° to the chest. as the picture shows. will Ezfit linking Hydraulic Wheel 26 Grounding guide This product must have grounding. If error and damage occurred to the treadmill , grounding wire can form one circuit with lowest resistance, the current can be guided into the ground to reduce the danger of electric shock. This product is equipped with one cable, which has one grounding conductor and grounding plug. The treadmill must be grounded with correct socket that is compatible with local rules. Danger! If you do not know whether the equipment is properly grounded, please consult a qualified electrician or maintenance personnel. Please do not change the plug attached to this product without authorization. If the plug is inconsistent with the socket, let a qualified electrician install a suitable socket. PRODUCT USING INSTRUCTIONS Using instruction of treadmill 1. Turn the power on, keep the treadmill spread out at its lowest position and check if its function is normal. 2. Clip the safety key cord with your clothes. 3. Ensure and check its function and stability before using.Standing on the Running belt to get it started is not allowed.The correct way to start is standing on side rails with hands on the handle bar. After normal working, you can exercise with the treadmill.Hold the handle bar when press the "START" key, the treadmill running at the speed of 1.0km/h after 5 seconds. Then press "+ "Key to 2.5-3.5 km/h which is the comfort speed for running. Both of hands are supposed to catch handle bar at the same time and feet step to the running belt successively to start running. Run at the same pace as your running belt. 4. After several minutes, you can speed up by pressing "+"key or slow down by "-"key meanwhile holding the hand bar. 5. When running, press speed value, you can enter into the fixed speed you want. 6. Pressing "stop" key at any time to stop the motor. 7. Pre-setting Use Connect the power .Turn the power on. Press "choose" key to select what mode you want. Press "starts" key to get started in your selected mode. You can press "+" or "-"to change the speed or "stop" key to make it stop. 8. HRC testing After the treadmill is powered on, hold your hands on the metal pulse sensors, then you can see HRC value on the display window. 27 Note: When the safety key pull out ,the treadmill will stop immediately, And the computer can not work ,the window shows "----". Treadmill Maintenance 1. Lubrication After the running belt has been used for a period of time, it must be lubricated with the configured methyl silicone oil. Suggestion Using time less than 3 hours every week lubrication once every 5 months Using time equal to 4-7 hours every week lubrication once every 2 months Using time more than 7 hours every week lubrication once every month No excessive lubrication. Note: the important factor of increase the lifetime for treadmill is proper lubrication. 2. The way of checking whether the running belt need lubrication is, lift the side soft the treadmill and feel the central back of the belt, as far as possible. If traces of silicon spray are found, lubrication is not necessary. If the surface is dry, the belt needs lubrication. Application of lubricant on the belt: (as shown) Stop the running belt, and fold the treadmill. Put up the belt of back main frame so that the oil can reach the middle position. Spraying silicone oil on the inner side of the running belt and coating silicone oil on both sides of the running belt. Run the treadmill at a speed of 1km/h to apply silicone evenly. And tread lightly on the running belt from left to right. Wait several minutes to let the silicon spray spread, before starting the machine Cleaning Regular cleaning of the striding belt ensures a long product life. Warning: The treadmill must be turned off to avoid electrical shocks. The power cord must be pulled out of the socket,before starting the cleaning or maintenance. After training: Wipe the console and other surfaces with a clean soft and damp cloth to remove sweat residues. Caution: Do not use any abrasives or solvents. To avoid damage to the computer, keep any liquids away. Do not expose the computer to direct sunlight. Weekly: To make the cleaning easier it is recommended to use a mat for the treadmill. Shoes can leave dirt on the striding belt that can fall beneath the treadmill. Clean the mat under the treadmill once a week. Storage: Store you treadmill in a clean and dry environment. Ensure the master powers witch is off and is unplugged from the electrical wall outlet. 1. Belt Adjustment All running belts are properly set at the factory and after assembly. However, slack may occur after a period of use. Such as : pause and slip may occur when running. When this phenomenon occurs, adjust the running belt and screw in half a turn left and right. If the running belt is loose, the running belt and the roller will slip in turn. But 28 too tight is also not good, which is easy to increase the load of the motor and damage the motor, running belt and roller, etc. 2. Adjusting the belt deviation: All running belts are properly set at the factory and after assembly. But after a period, the belt have the possibility for deviation. The reasons can be listed as follows. The treadmill is unstable. Feet didn't in the central of the running belt when running. Feet exert uneven force. If deviation caused by manual, No - load rotation for a few minutes can return to normal. Adjusting step by step in half a turn with a 6mm Allen wrench that is equipped randomly for unable to restore automatically. loose tight tight loose Such as left deviation of running belt. Adjust the left screw clockwise or the right screw anti-clockwise. Such as right deviation of running belt. Adjust the right screw clockwise or the left screw anti-clockwise. KEY POINT: -Clockwise means tighten. -Anti-clockwise means loosen. -Running belt will shift to the loose side. If the running belt shifts to the left, that means the left side is too loose. Adjust the left bolt clockwise to make the left tighter. Or adjust the right screw anti-clockwise to make the right looser. If the running belt shifts to the right, that means the right side is too loose. Adjust the right bolt clockwise to make the right tighter Or adjust the left screw anti-clockwise to make the left looser. Attention: -You need to start the treadmill (let the belt run) at a low speed before you adjust the running belt. -When you adjust the bolt, don't rotate it too much. -After each adjustment you need to look for the changes in the running belt. Running belt deviation is not covered by the warranty, and is mainly maintained by users according to the instructions. Running deviation can seriously damage the running belt. It must be found and corrected in time. Running belt deviation does not belong to the scope of warranty, mainly by the user in accordance with the 29 manual self-maintenance.Deviation will seriously damage the running belt, must be found in time, timely correction. Adjustment of the motor's belt All the motor belt of treadmill must be adjust in the factory and after assembly. However, after a period of use, there may be slack or slip phenomenon. Adjustment Steps Turn the adjusting screw counterclockwise with wrench The adjustment range shall be subject to the belt load not slipping. NOTE: Regular cleaning of belts and pulley grooves Screw of adjustment Screw Motor Belt Front roller Common faults and treatment methods Part of the treadmill The problem The treadmill doesn't work Run with it Not moving smoothly The running belt slipped Possible causes A is unplugged B the security key is not embedded C circuit signal system open D power supply not turned on E the fuse blew A not enough lubrication Running straps are too tight A the running belt is too loose B the belt is loose Maintenance methods Plug into socket Embed the safety key in the panel Check the controller input and signal line Place power switch in NO position Replace the fuse Using a methyl silicone oil lubricant Adjust your running bands for tightness Adjust your running bands for tightness Adjust drive belt tightness 30 Part of the console Fault code Fault description Abnormal communication: E 1 between control and console after power-on. The motor cord is not connected properly. No speed sensor E 3 signal: the lower control voltage output to the DC motor, can not receive the motor speed feedback for more than 3 seconds. Incline learning E4 Over-current protection: under the running state, the control detects E5 that the DC motor current is greater than the rated current + 6A for more than 3 seconds. Explosion-proof impulse protection: the power supply voltage is E 6 abnormal or the motor is abnormal etc. causes the drive motor circuit to be damaged. Trouble shooting Controller shutdown into a fault state. Unable to start. The console shows the failure code, and the buzzer beeps three times. Possible reasons:control and the console communication is blocked, check the connection of the communication line, ensure that each core fully inserted. Replace the connection line if it is broken.. Shutdown into the fault state, the console buzzer sound 9times, and showing the fault code. If it returns to normal after shutdown, it can enter the standby state and restarted. Possible causes:Check whether the motor wire is connected, keep the wire is connected. Check whether the controller has any odor,replace the controller; Shutdown into the fault state, the console buzzer sound 9times, and showing the fault code. After shutdown 10s, enter the standby state,can be restarted. Possible causes: If no speed sensor signal for 3 seconds, check whether the sensor plug is not inserted or damaged, plug it in or replace the sensor. Check whether the lifting motor induction line is plugged in properly, re-plug the connector to make it reliable;check whether the AC line of the lift motor is plugged in correctly, and the AC line of the jack motor and the controller are marked correctly; check whether the connecting line of the motor is broken, replace the connecting line or the lift motor; and press the learning key on the control to learn again. Shutdown into the fault state, the console buzzer sound 9times, and showing the fault code. After shutdown 10s, enter the standby state,can be restarted. Possible causes: If the current exceeds the rated load, the system self-protection, or a part of the treadmill is stuck, causing the motor can not turn, the load is too heavy, the current is too large, the system self-protection; adjust the treadmill to start up again.Also, check whether the motor has a flow sound or burnt odor, replace the motor, or replace the controller, or check whether the power supply is inconsistent or low voltage, retest with correct voltage. Shutdown into the fault state, the console buzzer sound 9times, and showing the fault code. After shutdown 10s, enter the standby state,can be restarted Possible causes: check power supply voltage is lower than 50% of normal voltage, please use the correct voltage to re-test; check whether the controller has a smell, replace the controller; check whether the motor wires are connected, reconnect the motor wires. 31 Bluetooth APP for Treadmill Bluetooth connection supports Anyrun, Zwift and Kinomap AnyRun Download, register and log in the AnyRun APP, enter the setting page: Click Setting, which is at the right lower corner, click Devices, the APP will detect the Bluetooth codes, select the Bluetooth code, which is same as the code tagged on the equipment console, and pair. Zwift Download, register and log in the Zwift APP, enter the setting page: Under PAIRED DEVICES page, click RUN for treadmill; Then click POWER SOURCE, and there is pop-up menu, select the Bluetooth code, which is same as the code tagged on the equipment console, then select OK to be paired. NOTE: Zwift remembers the devices used in the previous session and may attempt to pair to those devices if they are present and available. If you see devices paired that you don't wish to use, you can simply deselect them and select the device you do wish to pair. Kinomap Download, register and log in the Kinomap APP, enter the setting page: click More in the right lower conner, click Equipment management, click + at the right upper area, select for treadmill; Then select the Bluetooth brand of your choice e.g., Anyrun etc.; Click the content under Interactive, the APP detects found equipment, select the Bluetooth code, which is same as the code tagged on the equipment console, then click ADD NEW EQUIPMENT, it will pop out equipment successfully added. 32