randell 9000W-290 Series Solid Hinged Door Prep Table Instruction Manual

Instruction Manual for randell models including: 8000-290, 9000W-290, 9000W-290 Series Solid Hinged Door Prep Table, Solid Hinged Door Prep Table, Hinged Door Prep Table, Door Prep Table

8000N-290, 8000W-290 & 9000W-290 Manual

Unified Brands » Raised Rail "Pizza" Prep Tables - Unified Brands

Unified Brands » Literature Links Results - Unified Brands

Owner's Manual

Randell 8260N-290 Refrigerated Raised Rail Prep Table Two-section 60" W

File Info : application/pdf, 28 Pages, 5.15MB

80009000W-290-Manual-MNL1803

PART NUMBER PP MNL1803, REV. H (05/22)

This manual provides information for:

OPERATOR MANUAL
IMPORTANT INFORMATION, KEEP FOR OPERATOR

8000-290 & 9000W-290 SERIES PREP TABLES

888-994-7636, fax 888-864-7636 unifiedbrands.net

THIS MANUAL MUST BE RETAINED FOR FUTURE REFERENCE. READ, UNDERSTAND AND FOLLOW THE INSTRUCTIONS AND WARNINGS CONTAINED IN THIS MANUAL.

FOR YOUR SAFETY Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
WARNING R290 flammable refrigerant in use. Improper installation, adjustment, alteration, service or maintenance can cause property damage, injury or death. Read the installation, operating and maintenance instructions thoroughly before installing or servicing this equipment.
NOTIFY CARRIER OF DAMAGE AT ONCE It is the responsibility of the consignee to inspect the container upon receipt of same and to determine the possibility of any damage, including concealed damage. Unified Brands suggests that if you are suspicious of damage to make a notation on the delivery receipt. It will be the responsibility of the consignee to file a claim with the carrier. We recommend that you do so at once.
Manufacture Service/Questions 888-994-7636.

RETAIN THIS MANUAL FOR FUTURE REFERENCE
NOTICE: Due to a continuous program of product improvement, Unified Brands reserves the right to make changes in design and specifications without prior notice. NOTICE: Please read the entire manual carefully before installation. If certain recommended procedures are not followed, warranty claims will be denied.
MODEL NUMBER _________________________
SERIAL NUMBER _________________________
INSTALLATION DATE ______________________ The serial number is located behind the hinged vented door of the compressor machine compartment. An example is shown here.

EQUIPMENT DESCRIPTION

MODEL

PAN

CAPACITY

1/3 SIZE

WORK

REAR OF UNIT

SURFACE (CLOSED COVER)

OVERALL (COVER OPEN)

DOORS

STORAGE HP CU. FT.

VOLT

AMPS NEMA SHIP WT.

8148N-290

48" 33" 35"

44"

52.5"

(1)27"

9.0

1/3 115/60/1

5-15P 405

8260N-290

60" 33" 35"

44"

52.5"

(2)24"

14.67

1/3 115/60/1

5-15P 459

8268N-290

68" 33" 35"

44"

52.5"

(2)27"

17.76

1/3 115/60/1

5-15P 484

8383N-290

83" 33" 35"

44"

52.5"

(2)24",(1)21" 23.55 (2) 1/4 115/60/1 5.8 5-15P 585

8395N-290

95" 33" 35"

44"

52.5"

(3)27"

28.18 (2) 1/4 115/60/1 5.8 5-15P 630

84111N-290

111" 33" 35"

44"

52.5"

(3)24",(1)21" 32.81 (2) 1/4 115/60/1 5.8 5-15P 675

MODEL
8148W-290 8268W-290 8395W-290

PAN

CAPACITY

1/6 SIZE

48"

68"

95"

WORK SURFACE (NO CUTTING BOARD)

REAR OF UNIT (NO COVER)

33"

35"

46.5"

33"

35"

46.5"

33"

35"

46.5"

OVERALL
53.5" 53.5" 53.5"

DOORS STORAGE HP CU. FT.

VOLT

AMPS NEMA SHIP WT.

(1)27" (2)27" (3)27"

9.0 17.76 28.18

1/3 115/60/1 6 1/3 115/60/1 6 (2) 1/4 115/60/1 5.8

5-15P 530 5-15P 595 5-15P 785

MODEL

PAN

CAPACITY

1/6 SIZE

9148W-290

48"

9260W-290

60"

9272W-290

72"

DOORS STORAGE

VOLT

AMPS

NEMA SHIP WT.

CU. FT.

(BASE &

RAIL)

33"

46.5"

(1) 27"

5.5

1/3

115/60/1

5-15P

405

33"

46.5"

(2) 24"

9.8

1/3

115/60/1

5-15P

465

33"

46.5"

(2) 27"

11.2

1/3

115/60/1

5-15P

510

Information contained in this document is known to be current and accurate at the time of printing/creation. Unified Brands recommends referencing our product line websites, unifiedbrands.net, for the most updated product information and specifications. © 2022 Unified Brands. All Rights Reserved.

IMPORTANT - READ FIRST - IMPORTANT

INTERIOR EVAPORATOR COVER

DANGER

WARNING RISQUE D'INCENDIE OU
D'EXPLOSION. INFLAMMABLE

ALERTE

RÉFRIGÉRANT UTILISÉ.

DO NOT REMOVE PANEL - HIGH VOLTAGE -

RISK OF FIRE OR EXPLOSION. FLAMMABLE REFRIGERANT USED.

NE PAS UTILISER DE DISPOSITIFS MÉCANIQUES POUR

DO NOT USE MECHANICAL DEVICES TO DEFROST REFRIGERATOR. DO NOT

DÉGIVRER LE RÉFRIGÉRATEUR. NE FAIRE AUCUN TUBE

QUALIFIED PERSONNEL ONLY NE PAS RETIRE LE PANNEAU - HAUTE TENSION -
PERSONNEL QUALIFIÉ SEULEMENT NO RETIRE EL PANEL - ALTA TENSIÓN -
CALIFICADO PERSONAL
CAUTION ATTENTIÓN

PUNCTURE REFRIGERANT TUBING.

RÉFRIGÉRANT DE

PONCTION.

SB6.1.2

MOVING PARTS, DO NOT OPERATE

WITH COVER REMOVED

RIESGO DE INCENDIO O EXPLOSIÓN. REFRIGERANTE INFLAMABLE UTILIZADO. NO

UTILICE DISPOSITIVOS MECÁNICOS PARA DESCONGELAR EL REFRIGERADOR. NO

PERFORE LA TUBERÍA DEL REFRIGERANTE.

PP LBL1701 REV B

PIÉCES MOBILES NE PAS FAIRE FONCTIONNER SANS COUVERCLE LAS PIEZAS DE MOVIMIENTO NO FUNCIONAN
CON LA CUBIERTA RETIRADA

EXTERIOR OF UNIT

CAUTION MISE EN GARDE RISQUE D'INCENDIE OU

D'EXPLOSION. ÉLIMINER

RISK OF FIRE OR EXPLOSION. DISPOSE OF PROPERLY IN ACCORDANCE WITH FEDERAL OR LOCAL REGULATIONS. FLAMMABLE REFRIGERANT USED.

(or DISPOSER) CORRECTEMENT CONFORMÉMENT AUX RÉGLEMENTATIONS FÉDÉRALES OU LOCALES. RÉFRIGÉRANT INFLAMMABLE UTILISÉ.
PP LBL1704 REV B

PRECAUCIÓN RIESGO DE INCENDIO O EXPLOSIÓN. DESÉCHELO ADECUADAMENTE CONFORME A REGLAMENTOS FEDERALES O LOCALES. REFRIGERANTE INFLAMABLE UTILIZADO. SB6.1.4

NEAR EXPOSED REFRIGERANT TUBING

CAUTION

MISE EN GARDE RISQUE D'INCENDIE OU D'EXPLOSION EN RAISON

RISK OF FIRE OR EXPLOSION DUE TO PUNCTURE OF REFRIGERANT TUBING; FOLLOW

DE LA PERFORATION DU TUBE RÉFRIGÉRANT; SUIVEZ ATTENTIVEMENT LES INSTRUCTIONS DE

HANDLING INSTRUCTIONS CAREFULLY. FLAMMABLE REFRIGERANT USED.

MANIPULATION. RÉFRIGÉRANT INFLAMMABLE UTILISÉ.

PRECAUCIÓN RIESGO DE INCENDIO O EXPLOSIÓN DEBIDO A LA PERFORACIÓN DE LA TUBERÍA DE

REFRIGERANTE; SIGA CUIDADOSAMENTE INFLAMABLE UTILIZADO.

LAS

INSTRUCCIONES

MANEJO.

REFRIGERANTE SB6.1.5
PP LBL1705 REV B

NEAR MACHINE COMPARTMENT AND NAMEPLATE

DANGER
RISK OF FIRE OR EXPLOSION. FLAMMABLE REFRIGERANT USED. TO BE REPAIRED ONLY BY TRAINED SERVICE PERSONNEL. DO NOT PUNCTURE REFRIGERANT TUBING.

DANGER RISQUE D'INCENDIE OU D'EXPLOSION. RÉFRIGÉRANT INFLAMMABLE UTILISÉ. POUR ÊTRE RÉPARÉ QUE PAR UN TECHNICIEN QUALIFIÉ. NE PAS PERFORER LE TUBE RÉFRIGÉRANT.

PELIGRO RIESGO DE INCENDIO O EXPLOSIÓN. REFRIGERANTE INFLAMABLE UTILIZADO. DEBE SER REPARADO

SOLAMENTE POR PERSONAL DE SERVICIO CAPACITADO. NO PERFORE LA TUBERÍA DEL REFRIGERANTE.

SB6.1.3.a

CAUTION

MISE EN GARDE RISQUE D'INCENDIE OU

D'EXPLOSION. RÉFRIGÉRANT

RISK OF FIRE OR EXPLOSION. FLAMMABLE

INFLAMMABLE UTILISÉ. CONSULTER LE MANUEL DE

REFRIGERANT USED. CONSULT REPAIR MANUAL / OWNER'S GUIDE BEFORE ATTEMPTING TO INSTALL OR SERVICE THIS PRODUCT. ALL SAFETY PRECAUTIONS MUST BE FOLLOWED.

RÉPARATION / GUIDE DE L'UTILISATEUR AVANT D'ESSAYER D'INSTALLER OU DE RÉPARER CE PRODUIT. TOUTES LES PRÉCAUTIONS DOIVENT ÊTRE RESPECTÉES.

PP LBL1703 REVB

PRECAUCIÓN RIESGO DE INCENDIO O EXPLOSIÓN. REFRIGERANTE INFLAMABLE UTILIZADO. CONSULTE EL MANUAL DE REPARACIÓN / MANUAL DEL USUARIO ANTES DE INSTALAR O REPARAR ESTE PRODUCTO. DEBEN SEGUIRSE LAS PRECAUCIONES DE SEGURIDAD.SB6.1.3.b

INSTALLATION

CAUTION:

THIS UNIT CONTAINS R290 FLAMMABLE REFRIGERANT. USE CAUTION WHEN HANDLING MOVING AND USE OF THE REFRIGERATOR OR FREEZER. AVOID DAMAGING THE REFRIGERANT TUBING OR INCREASE THE RISK OF A LEAK.

WARNING: FAILURE TO FOLLOW INSTALLATION GUIDELINES AND RECOMMENDATIONS MAY VOID THE WARRANTY ON YOUR UNIT.

WARNING: IT IS IMPORTANT THAT YOUR UNIT HAS ITS OWN DEDICATED LINE. CONDENSING UNITS ARE DESIGNED TO OPERATE WITH A VOLTAGE FLUCTUATION OF PLUS OR MINUS 10% OF THE VOLTAGE INDICATED ON THE UNIT DATA TAG. BURN OUT OF A CONDENSING UNIT DUE TO EXCEEDING VOLTAGE LIMITS WILL VOID THE WARRANTY.

THE DANFOSS CONTROLLER HAS LOW VOLTAGE PROTECTION AND WILL NOT OUTPUT VOLTAGE TO THE COMPRESSOR IF VOLTAGE IS LESS THAN
104V.

WARNING: IT IS IMPORTANT THAT A VOLTAGE READING BE MADE AT THE COMPRESSOR MOTOR ELECTRICAL CONNECTIONS, WHILE THE UNIT IS IN OPERATION TO VERIFY THE CORRECT VOLTAGE REQUIRED BY THE COMPRESSOR IS BEING SUPPLIED. LOW OR HIGH VOLTAGE CAN DETRIMENTALLY AFFECT
OPERATION AND THEREBY VOID ITS WARRANTY.

WARNING: EVAPORATOR FANS RUN CONTINUOUSLY WHILE THE BASE IS POWERED ON.

WARNING: THIS UNIT IS INTENDED FOR USE IN LABORATORIES IN COMMERCIAL, INDUSTRIAL, OR INSTITUTIONAL OCCUPANCIES AS DEFINED IN THE SAFETY STANDARD FOR REFRIGERATION SYSTEMS, ASHRAE 15.

SELECTING A LOCATION FOR YOUR NEW UNIT
The following conditions should be considered when selecting a location for your unit:
1. Floor Load: The area on which the unit will rest must be level, free of vibration, and suitably strong enough to support the combined weights of the unit plus the maximum product load weight. All casters must be in contact with the floor to support the weight. Casters may require shims in order for the caster to be in contact with the floor. NOTE: If there is a question pertaining to weight load limits, consult the factory at 1-888-994-7636.
2. Clearances: Unit shall have a clearance of 0 inches at the top, 0 inches at the rear and 0 inches at each side.
3. Ventilation: The air cooled self contained unit requires a sufficient amount of cool clean air. Avoid surrounding your unit around other heat generating equipment and out of direct sunlight. Also, avoid locating in an unheated

room or where the room temperature may drop below 70° F (21°C) or above 86°F (32°C). Do not place any object that can block the ventilation exhaust from the machine compartment register.
INSTALLATION CHECKLIST
After the final location has been determined, refer to the following checklist prior to start-up:
1. Check all exposed refrigeration lines to ensure that they are not kinked, dented, or rubbing together or rubbing against any steel.
2. Check all visible components for any potential damage.
3. Check that the condenser and evaporator fans rotate freely without striking any stationary members.
4. Unit must be property leveled; Check all legs or casters ensure they all are in contact with the floor while maintaining a level work surface. Adjusting bullet feet height or shimming casters may be necessary if the floor is not level. NOTE: Damage to equipment may result if not followed. Unified Brands is not responsible for damage to equipment if improperly installed.
5. Plug unit into power source. Unit will come on. If unit does not turn on, refer to controller operation section of this manual to manually turn on the unit.
6. Allow unit time to cool down to holding temperature. If temperature adjustments are required, the control is located on the front panel. Confirm that the units is holding the desired temperature.
7. If unit has drawers, check drawer to ensure the drawer slides freely and fully extents along with seating in the cabinet properly when closed.
8. Refer to the front of this manual for serial number location. Please record this information in your manual on page 1 now. It will be necessary when ordering replacement parts or requesting warranty service.
9. Allow your unit to operate for approximately 45 minutes before putting in food in the rail. Allow 2 hours for base of the unit to cool down to storage temperature, prior to loading product. NOTE: All motors are oiled and sealed.
ELECTRICAL SUPPLY
The wiring should be done by a qualified electrician in accordance with local electrical codes. A properly wired and grounded outlet will assure proper operation. Please consult the data tag attached to the compressor to ascertain the correct electrical requirements. Supply voltage and amperage requirements are located on the serial number tag located on the rear interior wall.

OM-8000 & 9000W SERIES PREP TABLES

OPERATION

AMBIENT CONDITIONS
Unit is designed for normal operating temperatures between 70° F (21°C) - 86°F (32°C). Operating outside of those temperatures may cause premature product wear or failure.
Unified Brands has attempted to preset the temperature control to ensure that your unit runs at an optimum temperature, but due to varying ambient conditions, including elevation, food type and your type of operation, you may need to alter this temperature using control adjustment until desired temperature is reached.
CAREL CONTROLLER OPERATION

LED

FUNCTION

Compressor energized

Defrost in progress

Evaporator fan energized

MECHANICAL COMPARTMENT
WARNING: BASE EVAPORATOR FANS ARE ALWAYS IN OPERATION WHEN THE UNIT IS ENERGIZED. DISCONNECT POWER TO THE UNIT PRIOR TO PERFORMING MAINTENANCE.

An alarm is occurring

1. To power on the base, press and hold the base control power button until the LED display turns on. To power on the rail, press and hold the rail control power button until the LED display turns on. The power controls are located above the louver panel.

2. To power off the base press and hold the base control power button until the LED display turns off. To power off the rail press and hold the rail control power button until the LED display turns off. The power controls are located above the louver panel.

3. The drain valve for the upper rail is found behind the hinged vented door. The rail may be drained by placing a pan under the drain valve and opening the valve. (See Evening Shut Down of Prep Rail).
MORNING STARTUP OF PREP RAIL

1. Unit cleaning may be performed at this time.

2. Turn on unit. See item 2 under the Mechanical Compartment section above for powering on the rail.

3. Allow a minimum 45 minutes for your unit to cool down before loading product. A uniform frost pattern will appear on side walls and bottom of prep rail area.

4. Load the product and proceed with food preparation. NOTE: Product entering unit must be at 35°F +/- 2°F.
EVENING SHUT DOWN OF PREP RAIL

1. Remove product from unit at the end of the day's preparation.

2. Turn off unit. See item 3 under the Mechanical Compartment section above for powering on the rail.

3. Unit cleaning may be performed at this time if the frost has melted off the surface.

4. Once defrosted, the rail drain may be opened to remove any water that has resulted from the defrosting procedure.

WARNING: IT IS RECOMMENDED TO ONLY MAKE CHANGES OF 2 DEGREE INCREMENTS AT A TIME. ALLOW FOR THE UNIT TO OPERATE 24 HOURS BETWEEN ADJUSTMENTS. IF THE 2 DEGREE ADJUSTMENT IS NOT ENOUGH ANOTHER ADJUSTMENT CAN BE MADE. IF THE SETTINGS NEED TO GO ABOVE OR BELOW THIS POINT THERE MAY BE OTHER CONTRIBUTING FACTORS AS TO THE CAUSE OF THE TEMPERATURE VARIANCES, PLEASE CONTACT THE FACTORY AT 1-800-621-8560.

OM-8000 & 9000W SERIES PREP TABLES

POWER ON / OFF: Press and hold the Power Button seconds or until LED display turns On/Off.

for more than 3

MANUAL DEFROST: Press and hold the Defrost Button seconds (melting snowflake will light).
CHANGE SET POINT: To raise temperature

for more than 3

1. Press and hold set button for 1 second to access set point.

2. When set point starts flashing, press up button to adjust set point. 3. Press set button for 3-seconds to save set point. CHANGE SET POINT: To lower temperature 1. Press and hold set button for 1 second to access set point.

2. When set point starts flashing, press down button 3. Press set button for 3-seconds to save set point.

to adjust set point.

DANFOSS CONTROLLER OPERATION LED

FUNCTION

Compressor energized & Evaporator fan de-energized

Defrost in progress

Fans delay after defrost completion

ºC / ºF

Evaporator fan energize An alarm is occurring Temperature unit

MANUAL DEFROST

DRAWER REMOVAL 1. Fully extend the drawer that is to be removed. 2. Remove product pans from drawer. 3. Lift up the drawer stop tabs on each side of drawer track. 4. Pull drawer out while lifting the tabs.

POWER ON / OFF

CHANGE SET POINT

POWER ON / OFF: Press and hold the power button until LED display turns On / Off MANUAL DEFROST: Press and hold "Defrost" Button CHANGE SET POINT: To raise temperature 1. Press and hold " " to access set point. 2. When set point start flashing, Press " " to adjust set point. 3. After 30 seconds, the display automatically reverts to showing the current
temperature. CHANGE SET POINT: To lower temperature 1. Press and hold "v" to access set point. 2. When set point start flashing, Press "v" to adjust set point. 3. After 30 seconds, the display automatically reverts to showing the current
temperature. CHANGE FROM ºF /ºC : 1. Press the up/down buttons simultaneously for 5 seconds to access the menu. 2. Password is requested. Password is 000. 3. Press the bottom left button to OK the password. 4. Using the up/down buttons, navigate to the "diS" level. Press the bottom left
button to OK the selection. 5. Using the up/down buttons, navigate to the "CFu" level. Press the bottom left
button to OK the selection. a. "-F" designates Fahrenheit. b. "-C" designates Celsius. 6. Press the top left button repeatedly to return to exit and return to the home screen. DRAINING THE RAIL 1. Open hinged mechanical compartment door 2. Place container under drain valve 3. Open valve until all water has drained 4. Close valve 5. Discard water

DRAWER INSTALLATION
To remove and re-install individual drawers and drawer tracks, please refer to the figure above for proper installation instructions.
MAINTENANCE
WARNING: DO NOT USE SHARP UTENSILS AND/OR OBJECTS. WARNING: DO NOT USE STEEL PADS, WIRE BRUSHES, SCRAPERS, OR CHLORIDE
CLEANERS TO CLEAN YOUR STAINLESS STEEL. CAUTION: DO NOT USE ABRASIVE CLEANING SOLVENTS, AND NEVER USE
HYDROCHLORIC ACID (MURIATIC ACID) ON STAINLESS STEEL. WARNING: DO NOT PRESSURE WASH EQUIPMENT AS DAMAGE TO ELECTRICAL
COMPONENTS MAY RESULT.
Unified Brands strongly suggests a preventive maintenance program which would include the following monthly, weekly, and daily procedures:
If a failure of the equipment is a direct result of any of the Preventative Maintenance guidelines being neglected, the repairs and parts replacements will not be covered under warranty.
It is recommended that the customer contact the local Authorized Service Agent to provide a quote to perform periodic Preventative Maintenance. WEEKLY PM PROCEDURES
1. Clean all gaskets on a weekly if not daily basis with a solution of warm water and a mild detergent to extend gasket life. Do not use bleach for cleaning gaskets. Bleach will cause the gaskets to become brittle and not reach their normal life expectancy.
2. Clean and disinfect rail drains with a solution of warm water and mild detergent on a weekly basis. It is recommended to open and close the drain valve as the hot water is flowing through to clean any debris from the internal valve components.

OM-8000 & 9000W SERIES PREP TABLES

MONTHLY PM PROCEDURES
1. Cleaning of all condenser coils on a monthly basis. Condenser coils are a critical component in the life of the compressor and must remain clean to assure proper air flow and heat transfer. Failure to maintain this heat transfer will affect unit performance and eventually destroy the compressor. Clean the condenser coils with coil cleaner and/or a vacuum, cleaner and brush. NOTE: Brush coil in direction of fins, normally vertically as to not damage or restrict air from passing through condenser.
2. Clean and disinfect drain lines and evaporator pan with a solution of warm water and mild detergent on a monthly basis. Remove clear plastic drain line from plastic tray of condensing unit and place pan under end of drain tube. Discard waste water from pan when cleaning is complete. Re-insert plastic drain tube into position on condensing unit.
3. Remove drawer tracks as per instructions on Drawer Installation guidelines. Once drawers are removed wipe away any debris buildup from the drawer tracks.
The roller bearings come lubricated from the factory. Excessive oils and or water may remove the oils. It may be required to add lithium grease from time to time on bearings that appear dry.
4. Inspect all silicone seams at interior of the rail and refrigerated base cabinet on a monthly basis. Re-apply food grade silicone sealant as needed to any seams where silicone has peeled away or cracked. Apply silicone to a clean dry surface. Allow sufficient drying time to assure best adhesion of sealant.
RECOMMENDED CLEANERS FOR YOUR STAINLESS STEEL INCLUDE THE FOLLOWING:

JOB

CLEANING AGENT

COMMENTS

Routine cleaning

Soap, ammonia, detergent Medallion

Apply with a sponge or cloth

Fingerprints and smears

Arcal 20, Lac-O-Nu, Ecoshine

Provides a barrier film

Stubborn stains and discoloration

Cameo, Talc, Zud, First Impression

Rub in the direction of the polish lines

Greasy and fatty acids, blood, Easy-Off, Degrease It,

burnt-on foods

Oven Aid

Excellent removal on all finishes

Grease and Oil

Any good commercial detergent

Apply with a sponge or cloth

Restoration/Preservation

Benefit, Super Sheen

Good idea monthly

Reference: Nickel Development Institute, Diversey Lever, Savin, Ecolab, NAFEM

Proper maintenance of equipment is the ultimate necessity in preventing costly repairs. By evaluating each unit on a regular schedule, you can often catch and repair minor problems before they completely disable the unit and become burdensome on your entire operation.

For more information on preventive maintenance, consult your local service company or CFESA member. Most repair companies offer this service at very reasonable rates to allow you the time you need to run your business along with the peace of mind that all your equipment will last throughout its expected life. These services often offer guarantees as well as the flexibility in scheduling or maintenance for your convenience. For a complete listing of current Unified Brands ASA please visit www.unifiedbrands.net.

Unified Brands believes strongly in the products it manufactures and backs those products with one of the best warranties in the industry. We believe with the proper maintenance and use, you will realize a profitable return on your investment and years of satisfied service.

REPLACEMENT PARTS
To order parts, contact your Authorized Service Agent. Supply the model designation, serial number, part description, part number, quantity, and when applicable, voltage and phase.

TROUBLESHOOTING
This unit is designed to operate smoothly and efficiently if properly maintained. However, the following is a list of checks to make in the event of a problem. Wiring diagrams are found at the end of this manual. When in doubt, turn unit off and contact service at 888-994-7636.

SYMPTOM Unit does not run Unit too cold

POSSIBLE CAUSE No power to unit Control in OFF position Faulty control Incorrect set point Door / drawer ajar

Gasket torn or out of place

Unit too warm

Incorrect set point

Warm product introduced to cabinet

Ice on the coil

Unit noisy

Ice on the coil

Unit does not defrost Excessive ice on the coil

CAREL CONTROLLER CODES

PROCEDURE Plug in unit Turn controller on Call for service at 888-9947636 Adjust control set point Ensure door / drawer is fully closed Inspect the gasket for wear and position Adjust control set point
Pre-chill product 37ºF
Initiate manual defrost Initiate manual defrost Initiate manual defrost

DISPLAYED ALARM CODE E0 E1 dOr LO HI CHt

Control probe Defrost probe Open door Low temperature High temperature Dirty condenser

DANFOSS CONTROLLER CODES

ALARM

DISPLAYED ALARM CODE
Hi
Lo

ALARM High Temperature Alarm Low Temperature Alarm

CON

Condenser Temperature High Limit

uHi

Line Voltage Too High

uLi

Line Voltage Too Low

ACTION
Inspect door/drawer sealing
Contact service
Contact service
Clean condenser coil
Inspect coil for any objects obstruction hindering airflow
Contact service
Verify voltage of power source, to be performed by qualified technician
Contact service
Verify voltage of power source, to be performed by qualified technician
Contact service

OM-8000 & 9000W SERIES PREP TABLES

Inspect door/drawer sealing

LEA

Continuous Compressor Runtime

Inspect condenser coil, clean if necessary

Contact service

E01

S1 Sensor Failure

Contact service

E02

S2 Sensor Failure

Contact service

E03

S3 Sensor Failure

Contact service

E04

S4 Sensor Failure

Contact service

SERVICE

CAUTION:

COMPONENT PARTS SHALL BE REPLACED WITH FACTORY OEM PARTS. SERVICE WORK SHALL BE DONE BY FACTORY AUTHORIZED SERVICE PERSONNEL, SO AS TO MINIMIZE THE RISK OF POSSIBLE IGNITION DUE TO INCORRECT PARTS OR IMPROPER SERVICE.

CAUTION: BEFORE MAKING ANY REPAIRS, ENSURE THE UNIT IS DISCONNECTED FROM ITS POWER SOURCE.

This piece of equipment uses a R290 Refrigeration system. This equipment has been clearly marked on the serial tag the type of refrigerant that is being used. There is also a warning labels stating that the unit contains R290 refrigerant. R290 is safe to use as long as you follow these warning labels.
No smoking or open flames when servicing this equipment. If needed, use a CO2 or powder type fire extinguisher.
Replacement parts used on any R290 Refrigeration system cabinet must have specific UL certification for non-sparking components.
Only authorized service technician, certified in R290 system should service this equipment. MANIFOLD SET
A R134A manifold set can be used for servicing this equipment. REFRIGERANT RECOVERY
Follow all national and local regulations for R-290 refrigerant recovery. LEAKING CHECKING AND REPAIR
Leak check an R-290 system the same way you would an R-134a or R-404A system with the following exceptions.
1. Do not use a Halid leak detector on a R290 system.
2. Electronic leak detector must be designated specifically for combustible gas.
Use of a bubble solution or an ultrasonic leak detector are acceptable.
When repairing a leak, it is recommended using oxygen free dry nitrogen with a trace gas not exceeding 200PSI.
When accessing an R290 system, piercing valves are not to remain on the equipment in a permanent manner. After charge is recovered, Schrader valves are to be installed on the process stubs. Proper charge is to be weighed into the system and the system is to be leak checked afterwards.
The R290 equipment must have red process tubes and other devices through which the refrigerant is serviced, such as any service port. This color marking must remain on the equipment. If marking is removed, it must be replace and extend at least 2.5 centimeters (1") from the compressor. CHARGING
Follow the charge amount specified on the data tag. It is recommended to use the shortest hoses possible to prevent undercharging.
· Ensure the system is sealed and leak checked
· Evacuate system to a minimum 500 micron
· Weigh in correct charge

· Leak check the system again
· Bleed the refrigerant from the high side hose to the low side hose
· Disconnect the hoses
· Remove line taps
WARRANTY
Congratulations on the purchase of your new Unified Brands equipment. We hope you enjoy many years of reliable service in connection with the same. Please review all of the important safety and operational information contained in the Operator's Manual for this equipment before it is placed in service. If you have any questions related to equipment set up, operations, or service, please call 888-994-7636.
In addition, please review the sales terms and conditions set forth below.
*****IMPORTANT NOTICE*****
WARRANTIES, LIMITATIONS ON WARRANTIES, AND LIMITATION OF REMEDIES
The following Warranties, Limitation on Warranties, and Limitation of Remedies are included in the terms of sale for this product. Please read this entire warranty and all warranty modifications, disclaimers, and limitations of remedies set forth herein before accepting or using this equipment or product. Customer acknowledges and accepts the provisions of this notice by Customer's acceptance and use of the product. If these provisions are not acceptable and agreed to by Customer, then please return this product in its unused condition to Unified Brands or a Unified Brands authorized dealer.
UNIFIED BRANDS warrants this product against defects in material and workmanship under normal use and services for which this product was designed. This warranty runs only to the original end user and is in lieu of any other liability for defects. THE WARRANTIES EXPRESSED IN THESE TERMS AND CONDITIONS ARE IN PLACE OF ANY AND ALL OTHER EXPRESS WARRANTIES (UNLESS SEPARATELY STATED IN PRINTED MATERIAL PREPARED BY US DESCRIBING OUR EQUIPMENT) AND EXCLUDE ALL IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE; NOR ARE THERE ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, BY OPERATION OF LAW OR OTHERWISE. In no event shall UNIFIED BRANDS be liable for damages or delay or for any consequential, special or contingent damages arising out of any breach of our warranty, whether or not we have knowledge of specific needs or our employees or agents have given any specific assurances. Anyone claiming that there has been a breach of warranty by UNIFIED BRANDS must give us written notice within THIRTY (30) days after discovery of the relevant defect or the right to assert such claim will have been waived conclusively and provided further that any such claim must also be asserted within the general warranty period for such equipment and/or parts.
UNIFIED BRANDS will not be liable for any expense incurred without our prior written authorization for alterations made outside of our factory or for repairs which are not performed by UNIFIED BRANDS authorized service departments using UNIFIED BRANDS factory parts. Nor shall we be responsible for the performance of equipment as to which any repairs, revisions or alterations have been made by others.
THE EXCLUSIVE REMEDY OF THE USER OR BUYER AND THE EXCLUSIVE LIABILITY OF UNIFIED BRANDS OR ANY SELLER OF UNIFIED BRANDS PRODUCTS, FOR ANY AND ALL CLAIMS, LOSSES, INJURIES, OR DAMAGES (INCLUDING CLAIMS BASED ON BREACH OF WARRANTY, CONTRACT, NEGLIGENCE, TORT, STRICT LIABILITY, OR OTHERWISE) RESULTING FROM OR ARISING OUT OF THE USE OF HANDLING OF THIS PRODUCT, SHALL BE THE RETURN OF THE PURCHASE PRICE OR AN AMOUNT NOT TO EXCEED THE ORIGINAL PURCHASE PRICE OF THE PRODUCT OR, AT THE ELECTION OF UNIFIED BRANDS OR THE SELLER, THE REPLACEMENT OF THE PRODUCT.
https://unifiedbrands.net/ Randell-Warranty-Information

OM-8000 & 9000W SERIES PREP TABLES

CONTROLS
CALL FACTORY FOR REPLACEMENT PARTS: 888-994-7636

Parts List

SERVICE PART
RP CNT1720BCAR RP CNT1720RCAR RP CNT1805BCAR RP CNT1805RCAR
RF CNT2103 RF CNT2104 PP STK1802

CAREL CONTROLLER DESCRIPTION
CONTROLLER, CAREL, PROGRAMMED - BASE - SGL COMPR SYSTEM CONTROLLER, CAREL, PROGRAMMED - RAIL - SGL COMPR SYSTEM CONTROLLER, CAREL, PROGRAMMED - BASE - DBL COMPR SYSTEM CONTROLLER, CAREL, PROGRAMMED - RAIL - DBL COMPR SYSTEM THERMISTOR, CAREL, QTI, AIR SENSOR, BARE LEADS, BLACK, 10' THERMISTOR, CAREL, QTI, COIL SENSOR, BARE LEADS, BLUE, 10' OVERLAY, CONTROL PANEL, 8000N COMMON

XXX

XXXXXXXXXXXX XXXXXXXXXXXX

XXXXXXXXXXXX

8148N-290 8260N-290 8268N-290 8383N-290 8395N-290 84111N-290 8148W-290 8268W-290 8395W-290 9148W-290 9260W-290 9272W-290

SERVICE PART
RP CNT1720BC RP CNT1720RC RP CNT1805B RP CNT1805R
RF CNT1602 RF CNT1603 PP STK1802

DANFOSS CONTROLLER DESCRIPTION
CONTROLLER, DANFOSS, PROGRAMMED - BASE - SGL COMPR SYSTEM CONTROLLER, DANFOSS, PROGRAMMED - RAIL - SGL COMPR SYSTEM CONTROLLER, DANFOSS, PROGRAMMED - BASE - DBL COMPR SYSTEM CONTROLLER, DANFOSS, PROGRAMMED - RAIL - DBL COMPR SYSTEM THERMISTOR, DANFOSS, QTI, COIL SENSOR, MOLDED END, BLUE, 10' THERMISTOR, DANFOSS, QTI, AIR SENSOR, MODLED END, BLACK, 10' OVERLAY, CONTROL PANEL, 8000N COMMON

OM-8000 & 9000W SERIES PREP TABLES

XXX---XX-XXX XXX---XX-XXX ---XXX--X-----XXX--X---
XXXXXXXXXXXX XXXXXXXXXXXX XXXXXXXXXXXX

BASE UNIT, 8000N-290 & 8000W-290
CALL FACTORY FOR REPLACEMENT PARTS: 888-994-7636

Parts List

8148N-290 8260N-290 8268N-290 8383N-290 8395N-290 84111N-290 8148W-290 8268W-290 8395W-290

ITEM SERVICE PART

HD CST060

HD CST061

1B HD CST040HD 1C HD CST041HD

RP LVR1803

2A RP LVR1804 2B RP LVR1805

HD CTH9901

HD BMP034

RP SHD1805

5A RP SHD1806

5B RP SHD1807

5C RP SHD1808

RP PNL1803

HD SHL180

HD SHL160

7B HD SHL9912

HD PIN0102

RP BRK0107

10 RP BRK0108 11 RP BRK1811

12* EL WIR1703

13* HD LEG9902 14* RP BCK0107

14A* RP BCK0108

14B* RP BCK0109

14C* RP BCK0110

14D* RP BCK0111

14E* RP BCK0112

15 RP END1901

* = NOT SHOWN

6" CASTERS W/ BRAKE 6" CASTERS W/O BRAKE 4" CASTERS W/ BRAKE 4" CASTERS W/O BRAKE LOUVER, HINGED LOUVER, HINGED LOUVER, HINGED LOUVER MAGNET BUMPER, RUBBER SHROUD, COND UNIT SHROUD, COND UNIT SHROUD, COND UNIT SHROUD, COND UNIT COVER, ACCCESS SIDE CMPR, L OR R SHELF 22" X 25" SHELF 19" X 25" SHELF 16.15" X 25" SHELF SUPPORT PIN SHELF SUPPORT - FRT & BACK SHELF SUPPORT BETWEEN DOORS LOUVER MOUNTING HINGE BRACKET POWER CORD 16/3 - 9' - 90 6" LEG W/ BULLET FOOT S/S BACK PANEL 48" S/S BACK PANEL 60" S/S BACK PANEL 68" S/S BACK PANEL 83" S/S BACK PANEL 95" S/S BACK PANEL 111" SIDE PANEL

DESCRIPTION

OM-8000 & 9000W SERIES PREP TABLES

XXXXXXXXX

X-XXX

XXX

-X-------

-----X---

XXXXXXXXX

X-X-X-XX-

-X-------

- - -XX- - -X

-----X---

- - -XXX- -X

X-X-X-X-X

-X-X-X---

---X-X---

XXXXXXXXX

- - -XXX- -X

XXXXXXXXX

X-----X--

-X-------

--X----X-

---X-----

----X---X

-----X---

XXXXXXXXX

BASE UNIT, 9000W-290
CALL FACTORY FOR REPLACEMENT PARTS: 888-994-7636

Parts List

9148W-290 9260W-290 9272W-290

ITEM SERVICE PART

HD CST060

HD CST061

1B HD CST040HD

1C HD CST041HD

RP LVR1807

2A RP LVR1808

2B RP LVR1809

HD CTH9901

HD BMP034

RP SHD1814

5A RP SHD1815

5B RP SHD1816

HD SHL160

HD SHL180

HD PIN001

RP SPT007

RP BRK1811

10* RP BRK0108

11* HD LEG9902

12* RP BCK0301

12A* RP BCK0304

12B* RP BCK0113

13* EL WIR469A

14* EL WIR1703

* = NOT SHOWN

DESCRIPTION
6" CASTERS W/ BRAKE 6" CASTERS W/O BRAKE 4" CASTERS W/ BRAKE 4" CASTERS W/O BRAKE LOUVER, HINGED LOUVER, HINGED LOUVER, HINGED LOUVER MAGNET BUMPER, RUBBER SHROUD, COND UNIT SHROUD, COND UNIT SHROUD, COND UNIT SHELF 19" X 25" SHELF 22" X 25" SHELF SUPPORT PIN SHELF SUPPORT LOUVER MOUNTING HINGE BRACKET SHELF SUPPORT BETWEEN DOORS 6" LEG W/ BULLET FOOT S/S BACK PANEL 48" S/S BACK PANEL 60" S/S BACK PANEL 72" CORD, 14 GA 18" FEMALE 000469-14 POWER CORD, 9' 16/3 W/90*-45* ANGLE PLUG (SJTO WIRE)

OM-8000 & 9000W SERIES PREP TABLES

XXX XXX XXX XXX X--X--X XXX XXX X--X--X X-X -XXXX XXX XXX -XX XXX X--X--X XXX XXX

FAN ASSIST
CALL FACTORY FOR REPLACEMENT PARTS: 888-994-7636

Parts List

8148N-290 8260N-290 8268N-290 8383N-290 8395N-290 84111N-290 8148W-290 8268W-290 8395W-290

ITEM SERVICE PART

RP FAN1801

RF FAN1401

RF FAN0703

* = NOT SHOWN

FAN ASSIST ASSY FAN ASSIST MOTOR FAN ASSIST FAN GUARD

OM-8000 & 9000W SERIES PREP TABLES

DESCRIPTION

- - - -XX- -X - - - -XX- -X - - - -XX- -X

MECH COMPARTMENT SINGLE COMPRESSOR
CALL FACTORY FOR REPLACEMENT PARTS: 888-994-7636

Parts List

8148N-290 8260N-290 8268N-290 8383N-290 8395N-290 84111N-290 8148W-290 8268W-290 8395W-290 9148W-290 9260W-290 9272W-290

ITEM SERVICE PART

DESCRIPTION

RF CMP1702 COMPRESSOR, 1/3HP, R290, EMBRACO FFU130UAX

2* RF CMP1702SC COMPRESSOR, START COMPONENTS

RP CAP1801 CAP, TUBE - RAIL

RF FAN1401 CONDENSER FAN

RF FAN0703 FAN GUARD

RF FLT251 FILTER DRIER, 1/4" DBL INLET

RP BRK1720 MOUNTING CLIP, FILTER DRIER (T07-1167)

RF SOL9801 SOLENDOID VALVE

RP BRK1812 BRACKET, SOLENOID VALVE (T07-1173)

10 RF ACM1702 ACCUMULATOR

11 RP MNT1802 COMPRESSOR ASM STAND

RF COI1603 CONDENSER COIL

13 RP SHD1809 CONDENSER FAN SHROUD (T07-1179)

14 RP CPN1802 DRAIN PAN - (T07-1146)

15 HD WCK1702 PAD, WICKING

16*

EL WIR470 POWER CORD, 16GA 2' MALE

* = NOT SHOWN

OM-8000 & 9000W SERIES PREP TABLES

XXX- - -XX-XXX XXX- - -XX-XXX XXX- - -XX-XXX XXX- - -XX-XXX XXX- - -XX-XXX XXX- - -XX-XXX XXX- - -XX-XXX XXX- - -XX-XXX XXX- - -XX-XXX XXX- - -XX-XXX XXX- - -XX-XXX XXX- - -XX-XXX XXX- - -XX-XXX XXX- - -XX-XXX XXX- - -XX-XXX XXX- - -XX-XXX

MECH COMPARTMENT DOUBLE COMPRESSOR
CALL FACTORY FOR REPLACEMENT PARTS: 888-994-7636

Parts List

8148N-290 8260N-290 8268N-290 8383N-290 8395N-290 84111N-290 8148W-290 8268W-290 8395W-290

ITEM SERVICE PART

DESCRIPTION

RF CMP1604 COMPRESSOR, 1/4 HP, R290, EMBRACO, 115V-60HZ

2* RF CMP1604SC COMPRESSOR, START COMPONENTS

RP CAP1802 CAP, TUBE - RAIL

RF FAN0601 CONDENSER FAN

HD GRD1610 FAN GUARD

RF FLT251 FILTER DRIER, 1/4" DBL INLET

RF ACM1701 ACCUMULATOR

RP MNT1803 COMPRESSOR ASM STAND (T07-1168)

RF COI1603 CONDENSER COIL

10 RP SHD1810 CONDENSER FAN SHROUD (T07-1169)

11 RP CPN1803 DRAIN PAN (T07-1170)

EL WIR274 HEATER, DRAIN PAN

13*

EL WIR470 POWER CORD, 16GA 2' MALE

* = NOT SHOWN

OM-8000 & 9000W SERIES PREP TABLES

- - -XXX- -X - - -XXX- -X - - -XXX- -X - - -XXX- -X - - -XXX- -X - - -XXX- -X - - -XXX- -X - - -XXX- -X - - -XXX- -X - - -XXX- -X - - -XXX- -X - - -XXX- -X - - -XXX- -X

EVAPORATOR COIL
CALL FACTORY FOR REPLACEMENT PARTS: 888-994-7636

Parts List

8148N-290 8260N-290 8268N-290 8383N-290 8395N-290 84111N-290 8148W-290 8268W-290 8395W-290

ITEM SERVICE PART

RF COI107 EVAPORATOR COIL

RP CAP1804 CAP, TUBE - BASE

2A RP CAP1803 CAP, TUBE - BASE

RF FAN1401 FAN, EVAPORATORS

RP DRP107 EVAPORATOR DRAIN PAN

5 RP PNL107-290 SIDE, COIL, 8000N COMMON

6 RP PNL108-290 BACK, COIL, 8000N COMMON

7 RP PNL109-290 FRONT, COIL, 8000N COMMON

RP SHD1811 PLATE, FAN, 8000N COMMON

RP PNL1804 SIDE, COIL, NO PERF, 8000N COMMON

* = NOT SHOWN

DESCRIPTION

OM-8000 & 9000W SERIES PREP TABLES

XXXXXXXXX - - -XXX- -X XXX- - -XXXXXXXXXXX XXXXXXXXX XXXXXXXXX XXXXXXXXX XXXXXXXXX XXXXXXXXX X-----X--

EVAPORATOR COIL
CALL FACTORY FOR REPLACEMENT PARTS: 888-994-7636

Parts List

9148W-290 9260W-290 9272W-290

ITEM SERVICE PART

RF COI107 EVAPORATOR COIL

RP CAP1803 CAP, TUBE - BASE

RF FAN1401 FAN, EVAPORATORS

RP DRP107 EVAPORATOR DRAIN PAN

4A RP DRP107S EVAPORATOR DRAIN PAN/STAINLESS STEEL

5 RP PNL107-290 SIDE, COIL, 8000N COMMON 6 RP PNL108-290 BACK, COIL, 8000N COMMON

7 RP PNL109-290 FRONT, COIL, 8000N COMMON

RP SHD1811 PLATE, FAN, 8000N COMMON

RP PNL1804 SIDE, COIL, NO PERF, 8000N COMMON

* = NOT SHOWN

OM-8000 & 9000W SERIES PREP TABLES

DESCRIPTION

XXX XXX XXX XXX XXX XXX XXX XXX XXX X--

DOOR ASSEMBLY
CALL FACTORY FOR REPLACEMENT PARTS: 888-994-7636

Parts List

8148N-290 8260N-290 8268N-290 8383N-290 8395N-290 84111N-290 8148W-290 8268W-290 8395W-290

ITEM SERVICE PART

RF DOR0321

1A RF DOR0320

1B RF DOR0323

1C RF DOR0322

1D RF DOR0324

1E RF DOR0325

IN GSK9902

2A* IN GSK1025

2B* IN GSK1030

HD HDL0103

RP HNG9900

RP HNG026

RP HNG027

RP HNG023

RP HNG034

RP HNG035

HD BSH050

RP HNG025

* = NOT SHOWN

DESCRIPTION
DOOR HINGED LEFT, 21" DOOR HINGED RIGHT, 21" DOOR HINGED LEFT, 24" DOOR HINGED RIGHT, 24" DOOR HINGED LEFT, 27" DOOR HINGED RIGHT, 27" GASKET, 18.5" X 24.5" PUSH IN GASKET, 21.75" X 24.5" PUSH IN GASKET, 24.5" X 24.5" PUSH IN DOOR HANDLE (recessed) HINGE ASSY, UNIVERSAL, LEFT/RIGHT HINGE, STRAP L BRACKET TOP/BOTTOM HINGE, BOTTM l BRACKET W/ COLLOR HINGE, TOP L BRACKET W/O HINGE, TOP DOOR LH CHANNEL HINGE, TOP DOOR RH CHANNEL BUSHING, NYLON DOOR HINGE, SPRING LOAD ASSEMBLY

OM-8000 & 9000W SERIES PREP TABLES

---X-X-----X-X---X-X-X---X-X-X--X-X-X-X-X X-X-X-X-X ---X-X---X-X-X--X-X-X-X-X XXXXXXXXX XXXXXXXXX XXXXXXXXX XXXXXXXXX XXXXXXXXX XXXXXXXXX XXXXXXXXX XXXXXXXXX XXXXXXXXX

DOOR ASSEMBLY
CALL FACTORY FOR REPLACEMENT PARTS: 888-994-7636

Parts List

9148W-290 9260W-290 9272W-290

ITEM SERVICE PART

RP DOR0323

1A RP DOR0322

1B RP DOR0324

1C RP DOR0325

IN GSK1025

2A IN GSK1030

HD HDL0103

RP HNG9900

RP HNG026

RP HNG027

RP HNG023

RP HNG034

RP HNG035

HD BSH050

RP HNG025

* = NOT SHOWN

DOOR HINGED LEFT, 24" DOOR HINGED RIGHT, 24" DOOR HINGED LEFT, 27" DOOR HINGED RIGHT, 27" GASKET, 21.75" X 24.5" PUSH IN GASKET, 24.5" X 24.5" PUSH IN DOOR HANDLE (recessed) HINGE ASSY, UNIVERSAL, LEFT/RIGHT HINGE, STRAP L BRACKET TOP/BOTTOM HINGE, BOTTM l BRACKET W/ COLLOR HINGE, TOP L BRACKET W/O HINGE, TOP DOOR LH CHANNEL HINGE, TOP DOOR RH CHANNEL BUSHING, NYLON DOOR HINGE, SPRING LOAD ASSEMBLY

OM-8000 & 9000W SERIES PREP TABLES

DESCRIPTION

-X-XX-X X-X -XX-X XXX XXX XXX XXX XXX XXX XXX XXX XXX

DRAWER ASSEMBLY
CALL FACTORY FOR REPLACEMENT PARTS: 888-994-7636

Parts List

8148N-290 8260N-290 8268N-290 8383N-290 8395N-290 84111N-290 8148W-290 8268W-290 8395W-290

ITEM SERVICE PART

1 RP DRW0206 DRAWER ASSEMBLY - 21"

1A RP DRW0201PT DRAWER ASSEMBLY - 24"

1B RP DRW0202 DRAWER ASSEMBLY - 27" 2 RP MOD050A DRAWER CARTRIDGE - 21"

2A RP MOD030A DRAWER CARTRIDGE - 24"

2B RP MOD029A DRAWER CARTRIDGE - 27"

RF FRT9903 DRAWER FRONT - 21"

3A RF FRT9904 DRAWER FRONT - 24"

3B RF FRT9905 DRAWER FRONT - 27"

RP FRM0301 DRAWER FRAME - 21"

4A RP FRM0302 DRAWER FRAME - 24"

4B RP FRM0303 DRAWER FRAME - 27"

IN GSK9903 DRAWER GASKET - 18.75"

5A* IN GSK1041 DRAWER GASKET - 21.75"

5B* IN GSK1046 DRAWER GASKET - 24.75"

RP TRK05SM DRAWER TRACKS (1L & 1R)

HD HDL130 DRAWER HANDLE

HC BRG210 DRAWER BEARING

9* FA SCW5002 DRAWER BEARING BOLT

* = NOT SHOWN

OM-8000 & 9000W SERIES PREP TABLES

DESCRIPTION

---X-X---X-X-X--X-X-X-X-X ---X-X---X-X-X--X-X-X-X-X ---X-X---X-X-X--X-X-X-X-X ---X-X---X-X-X--X-X-X-X-X ---X-X---X-X-X--X-X-X-X-X XXXXXXXXX XXXXXXXXX XXXXXXXXX XXXXXXXXX

DRAWER ASSEMBLY
CALL FACTORY FOR REPLACEMENT PARTS: 888-994-7636

Parts List

9148W-290 9260W-290 9272W-290

ITEM SERVICE PART

RP FRT0304

1A RP FRT0306

RP FRT0303

2A RP FRT0305

HD HDL0130

RP TRK05SM

IN GSK1042

5A* IN GSK1043

5B* IN GSK1048

5C* IN GSK1047

6 RP MOD1701A

6A RP MOD1603A

RP FRM0103

7A RP FRM127E

HD BRG210

9* FA SCW5002

HD HDL130

HC BRG210

9* FA SCW5002

* = NOT SHOWN

DRAWER FRONT - BOTTOM - 24" DRAWER FRONT - BOTTOM - 27" DRAWER FRONT - TOP - 24" DRAWER FRONT - TOP - 27" DRAWER HANDLE DRAWER TRACKS (1L & 1R) DRAWER GASKET - 24" Top DRAWER GASKET - 24" Bottom DRAWER GASKET - 27" Top DRAWER GASKET - 27" Bottom DRAWER CARTRIDGE - 24" DRAWER CARTRIDGE - 27" DRAWER FRAME - 24" DRAWER FRAME - 27" DRAWER BEARING DRAWER BEARING BOLT DRAWER HANDLE DRAWER BEARING DRAWER BEARING BOLT

OM-8000 & 9000W SERIES PREP TABLES

DESCRIPTION

-XX-X -X--XXX XXX -X-XX-X X-X -XX-X -XX-X XXX XXX XXX XXX XXX

DRAIN ASSEMBLY
CALL FACTORY FOR REPLACEMENT PARTS: 888-994-7636

Parts List

8148N-290 8260N-290 8268N-290 8383N-290 8395N-290 84111N-290 8148W-290 8268W-290 8395W-290 9148W-290 9260W-290 9272W-290

ITEM SERVICE PART

PB VLV1803

PL TBG1801

HD CLM1801

HD CLP1902

PB ELB1801

EL GRM1801

HD DRN1702

* = NOT SHOWN

DESCRIPTION
VALVE, GREEN BACK, 25 MM TUBING, 1" VINYL, BLACK CLAMP, 1-1/4" OETIKER CLIP, SPRING, 1 TO 1-7/8 NICKEL PLATED STEEL ELBOW, 90 DEG GROMMET, PUSHON, DRAIN ASSY DRAIN, ABS, GRAY, 1.375", 1.00" NPS X 2.875" LG W/NUT & WASHER

OM-8000 & 9000W SERIES PREP TABLES

XXXXXXXXXXXX XXXXXXXXXXXX XXXXXXXXXXXX XXXXXXXXXXXX XXXXXXXXXXXX XXXXXXXXXXXX XXXXXXXXXXXX

RAIL ASSEMBLY - NARROW HOOD COVER
CALL FACTORY FOR REPLACEMENT PARTS: 888-994-7636

Parts List

8148N-290 8260N-290 8268N-290 8383N-290 8395N-290 84111N-290

ITEM SERVICE PART

HD PIN107 PIN, THREADED SOUTHCO

HD PIN107I INSERT, THREADED SOUTCHO

HD PIN001 PIN, KEY PAN RAIL

RP DSN001 DRAIN SCREEN, 2"

RP HNG006 HINGE, PAN COVER SET OF 2

HD PIN0101 PIN, LOCATING 0.875 LENGTH

7 FA NUT0403SS NUT, 1/4-20 CAP NUT 18-8 SS

RP PCR0115 COVER, HINGED PAN

8A RC PCR0117 COVER, HINGED PAN

8B RC PCR0118 COVER, HINGED PAN

8C RC PCR0114 COVER, HINGED PAN

8D RC PCR0115 COVER, HINGED PAN

8E RC PCR0116 COVER, HINGED PAN

* = NOT SHOWN

OM-8000 & 9000W SERIES PREP TABLES

DESCRIPTION

XXXXXX XXXXXX XXXXXX XXXXXX XXXXXX XXXXXX XXXXXX X-----X-----X-----X-----X-----X

RAIL ASSEMBLY - WIDE HOOD COVER
CALL FACTORY FOR REPLACEMENT PARTS: 888-994-7636

Parts List

8148N-290 8260N-290 8268N-290 8383N-290 8395N-290 84111N-290 8148W-290 8268W-290 8395W-290 9148W-290 9260W-290 9272W-290

ITEM SERVICE PART

RP HOD0101

1A RPHOD1801

1B RP HOD0301

1C RP HOD0202

1D RP HOD1802

1E RP HOD0407

1F RP HOD0310

1G RP HOD1803

1H HP HOD0609

HD ROD100

HD ROD200

HD PIN107

HD PIN107I

RP DSN001

RP LID048

RP HNG017

RP LID1502

RP LID068

RP LID083

RP LID095

RP LID111

RP LID1801

6G RP LID1802

6H RP LID1803

HD PIN001

* = NOT SHOWN

DESCRIPTION
HOOD COVER HOOD COVER HOOD COVER HOOD COVER HOOD COVER HOOD COVER HOOD COVER HOOD COVER HOOD COVER HOOD COVER, ROD W/ SINGLE BEND HOOD COVER, ROD W/ DOUBLE BEND PIN, THREADED SOUTHCO INSERT, THREADED SOUTCHO DRAIN SCREEN, 2" COVER (IMAGE ON LEFT) SLIDE BACK COVER (IMAGE ON RIGHT) COVER COVER COVER COVER COVER COVER COVER COVER PIN, KEY PAN RAIL

OM-8000 & 9000W SERIES PREP TABLES

X--------X--

------X---X-

-X---------X

--X---------

-------X----

---X

-------

----X-------

--------X---

-----X------

X- - -X-X-XX- -

----X---X---

XXXXXXXXXXXX

X-----------

- - - - - - - - -XXX

-X--------X-

--X--------X

---X--------

----X-------

-----X------

------X-----

-------X----

--------X---

- - - - - -XXX- - -

8000-290 SINGLE COMPRESSOR
CAREL

Wiring Diagram

16 - WHITE

POWER SUPPLY 115V-60HZ-1PH CORD WITH GROUNDED CAP EL WIR461-90
NEMA G 5-15P
PLUG
GREEN

16 - BLACK

16 - BROWN 18 - BLACK 18 - BLUE 18 - BLACK 16 - WHITE 16 - BROWN 18 - BLACK 18 - BLUE 18 - BLACK 16 - WHITE

16FLA(96LRA) RAIL CONTROL
16(10)A 240V~ 16A
123456 7
COMP

16FLA(96LRA) 16(10)A 240V~

BASE CONTROL

16A

123456 7

COMP

SENSOR CONNECTIONS 10K NTC

RAIL 8 9 10 11

BASE 8 9 10 11

RAIL SENSING TUBE

CONDENSER

AIR

(OPTION)

COMPRESSOR

COIL CONDENSER (DEF) (OPTION)

16 - BLACK
16 - WHITE 16 - BROWN

EL WIR470 NEMA 5-15 EL WIR469A

16 - BLACK

BLACK

FAN #1

CONDENSER BLACK

CONDENSER

16 - WHITE

BLACK

FAN #2

BLACK

16-WHITE

18 - BLUE 18 - BLUE

18 - BLACK 16 - WHITE

18 - BLUE

RAIL SOLENOID

18 - BLUE 18 - BLUE

BASE SOLENOID

18 - BLUE

18 - BLACK
18 - BLACK 18 - BLUE

EVAP FAN #1 EVAP FAN #2 EL WIR0005

18 - WHITE
18 - WHITE 18 - GREEN

18 - GREEN

16-WHITE

OM-8000 & 9000W SERIES PREP TABLES

8000-290 DOUBLE COMPRESSOR
CAREL

Wiring Diagram

POWER SUPPLY 115V-60HZ-1PH CORD WITH GROUNDED CAP NEMA # 5-15P

NEMA
G
5-15 PLUG

16FLA(96LRA) RAIL CONTROL
16(10)A 240V~ 16A
123456 7
COMP
35

GREEN

16-BROWN 16-BLACK 18-BLUE 16-BLACK 16-WHITE 16-BROWN 18-BLACK 18-BLUE 18-BLACK 16-WHITE

16FLA(96LRA) 16(10)A 240V~

BASE CONTROL

16A

123456 7

SENSOR CONNECTIONS 10K NTC

RAIL 8 9 10 11

BASE 8 9 10 11

COMP

RAIL SENSING TUBE

CONDENSER

AIR

(OPTION)

COIL CONDENSER (DEF) (OPTION)

16-BROWN

BASE COMPRESSOR 16-WHITE 16-WHITE

18-BLUE

CONDENSER FANS RAIL
BASE

18-BLUE 18-BLUE

16-WHITE 18-BLACK

16-WHITE

2 (OPTIONAL TIMER)

TIMER

16 - WHITE 16-WHITE

16-BROWN

RAIL COMPRESSOR

18-BLACK

COND HTR

16-WHITE

EVAP FAN #1 18-BLACK

16-WHITE

EVAP FAN #2 18-BLACK

16-WHITE

(OPTIONAL LED LIGHT)

16-WHITE

18-BLACK

16-WHITE FAN ASSIST OPTION ONLY

OM-8000 & 9000W SERIES PREP TABLES

9000W-290 CAREL

Wiring Diagram

16 - WHITE

POWER SUPPLY 115V-60HZ-1PH CORD WITH GROUNDED CAP EL WIR461-90
NEMA
G
5-15P PLUG
GREEN

16 - BLACK

16 - BROWN 18 - BLACK 18 - BLUE 18 - BLACK 16 - WHITE 16 - BROWN 18 - BLACK 18 - BLUE 18 - BLACK 16 - WHITE

16FLA(96LRA) RAIL CONTROL
16(10)A 240V~ 16A
123456 7
COMP

16FLA(96LRA) 16(10)A 240V~

BASE CONTROL

16A

123456 7

COMP

SENSOR CONNECTIONS 10K NTC

RAIL 8 9 10 11

BASE 8 9 10 11

RAIL SENSING TUBE

CONDENSER

AIR

(OPTION)

COMPRESSOR

COIL CONDENSER (DEF) (OPTION)

16 - BLACK
16 - WHITE 16 - BROWN

EL WIR470 NEMA 5-15 EL WIR469A

16 - BLACK

BLACK

FAN #1

CONDENSER BLACK

CONDENSER

16 - WHITE

BLACK

FAN #2

BLACK

16-WHITE

18 - BLUE 18 - BLUE

18 - BLACK 16 - WHITE

18 - BLUE

RAIL SOLENOID

18 - BLUE 18 - BLUE

BASE SOLENOID

18 - BLUE

18 - BLACK
18 - BLACK 18 - BLUE

EVAP FAN #1 EVAP FAN #2 EL WIR0005

18 - WHITE
18 - WHITE 18 - GREEN

18 - GREEN

16-WHITE

OM-8000 & 9000W SERIES PREP TABLES

8000-290 SINGLE COMPRESSOR
DANFOSS

Wiring Diagram

OM-8000 & 9000W SERIES PREP TABLES

8000-290 DOUBLE COMPRESSOR
DANFOSS

Wiring Diagram

OM-8000 & 9000W SERIES PREP TABLES

9000W-290 DANFOSS

Wiring Diagram

OM-8000 & 9000W SERIES PREP TABLES

Model No: Serial No: Date Purchased: Purchase Order No:
Date

Service Log
Purchased From: Location: Date Installed: For Service Call:
Maintenance Performed

Performed By

OM-8000 & 9000W SERIES PREP TABLES

References

Unified Brands » Re-imagining Food Preparation

Adobe PDF Library 16.0.7 Adobe InDesign 17.2 (Macintosh)