Personal Protective Equipment Manufacturer | Bullard
P65Warnings.ca.gov
User Manual for Bullard models including: RAM1, RAM2, RAM4, RAM21R, RAM41R, RAM8, RAM81R, RAM1 Remote Air Manifold, RAM1, Remote Air Manifold, Air Manifold, Manifold
File Info : application/pdf, 2 Pages, 331.84KB
DocumentDocumentRemote Air Manifold (RAM) Series User Manual WARNING The RAM series remote air manifold boxes are designed to meet NIOSH requirements for a point of attachment when the work area is located away from the filtration source or main air supply. The RAM must be supplied with at least Grade D breathable air at the required pressure (psi) and volume (cfm) as recommended by the respirator manufacturer. See Table 1 below. Failure to continuously supply at least Grade D breathable air to the RAM could cause death or serious injury or life-threatening delayed lung disease including but not limited to silicosis, pneumoconiosis or asbestosis. Point of Attachment (POA) Point of Attachment: A pressure gauge, regulator, relief valve and congruous fitting are necessary to be considered a POA. (Reference: Federal Law 42 CFR Part 84 Subpart J Section 84.149) Regulator allows adjustment of air pressure to manufacturer's specified pressure range based on range of hose length used. Pressure gauge allows verification of this pressure setting at the point of attachment. Pressure relief valve prevents pressure from exceeding 125 psi. Congruous fitting allows connection of "Detachable couplings" as part of NIOSH approved respirator system. Specifications (Table 1) Size (W x H x D) Outlets Nominal Air Flow (cfm) Maximum Inlet Pressure Maximum Outlet Pressure RAM1 19"x 13" x 7" 1 15 125 psi (8.6 bar) RAM2 RAM4 RAM21R RAM41R 19" x 13" x 7" 24" x 18" x 9" 2 4 30 50 150 psi (10.3 bar) 125 psi (8.6 bar) 125 psi (8.6 bar) RAM8 RAM81R 27" x 20" x 10" 8 100 125 psi (8.6 bar) Operating Instructions 1) Attach incoming air line to the 1/2" inlet air QD Nipple. Air supplied to the remote air manifold must be at least Grade D breathable air, as specified by Federal Law 29 CFR 1910.134(i). 2) Attach respirator air supply hose to the outlet air quick disconnect fittings on the RAM unit. 3) Adjust the outlet pressure to the setting recommended by the respirator manufacturer. Turn the pressure regulator knob clockwise to increase pressure or counterclockwise to decrease pressure. California Proposition 65 WARNING Cancer and Reproductive Harm - www.P65Warnings.ca.gov. Propuesta de California 65 ADVERTENCIA Cáncer y Daño Reproductivo - www.P65Warnings.ca.gov. Proposition de la Californie 65 AVERTISSMENT Cancer et Troubles de l'appareil reproducteur - www.P65Warnings.ca.gov. Shutdown 1. Make sure all personnel have left the work area 2. Shut off the incoming air to the remote air manifold 3. Release air pressure by pulling the relief valve ring out 4. Disconnect the airline hoses 5. Install dust caps to prevent entry of debris into the outlet fittings. www.bullard.com Regulator Pressure Relief Valve Outlet Coupler Replacement Parts Description Part Number CABREG1 ................................................................. Regulator 15 CFM CABREG1 ................................................................. Regulator 30 CFM CABREG2 ................................................................. Regulator 50 CFM CABREG3 ............................................................... Regulator 100 CFM CABREG4 ........................................................Independent Regulator 41PRV ....................................................................Relief Valve 125 psi Description Part Number CABQDHA.......................................................... Outlet Fitting Hansen CABQDSC ........................................................Outlet Fitting Schrader CABQDSN....................................................... Outlet Fitting Snap-Tite CABQDCE ................................................................Outlet Fitting Cejn CABQDSS...........................................Outlet Fitting Hansen Stainless One Year LIMITED Warranty Return Authorization Bullard warrants to the original purchaser that the Remote Air Manifold will be free of defects in material and workmanship under normal use and service for a period of one (1) year from the date of purchase. Bullard's obligation under this warranty is limited to repairing or replacing, at its option, parts that are returned within the warranty period and that are, after examination, shown to Bullard's satisfaction to be defective, subject to the following limitations. a) Remote Air Manifold must be returned to the Bullard factory with shipping charges prepaid. b) Remote Air Manifold must not be altered from its original factory configuration. c) Remote Air Manifold must not have been misused, subjected to negligent use or damaged in transport d) The date of purchase is within the one year warranty period. (A copy of the purchaser's original invoice showing the date of purchase is required to validate warranty coverage) In no event shall Bullard be responsible for damages for loss of use or other indirect, incidental, consequential or special costs, expenses or damages incurred by the purchaser, notwithstanding that Bullard has been advised of the possibility of such damages. ANY IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE SPECIFICALLY EXCLUDED FROM THIS WARRANTY. Some states do not allow the exclusion or limitation of incidental or consequential damages, or allow limitations on how long an implied warranty lasts, so the above limitations or exclusion may not apply to you. This warranty gives you specific legal rights, and you may have other rights which vary from state to state. The following steps must be completed before Bullard will accept any returned goods. Please read carefully. Follow the steps outlined below to return goods to Bullard for repair or replacement under warranty or for paid repairs: 1. Contact Bullard Customer Service by telephone or in writing at: Bullard 1898 Safety Way Cynthiana, KY 41031-9303 Toll-Free: 877-BULLARD (285-5273) Phone: 859-234-6616 In your correspondence or conversation with Customer Service, describe the problem as completely as possible. For your convenience, the representative will try to help you correct the problem over the phone. 2. Verify with your representative that the product should be returned to Bullard. Customer Service will provide you with written permission and a return authorization number as well as the labels you will need to return the product. 3. Before returning the product, decontaminate and clean it to remove any hazardous materials which may have settled on the product during use. Laws and/or regulations prohibit the shipment of hazardous or contaminated materials. Products suspected to be contaminated will be professionally discarded at the customer's expense. 4. Ship returned products, including those under warranty, with all transportation charges pre-paid. Bullard cannot accept returned goods on a freight collect basis. 5. Returned products will be inspected upon return to the Bullard facility. Bullard Customer Service will telephone you with a quote for required repair work which is not covered by warranty. If the cost of repairs exceeds stated quote by more than 20%, your coordinator will call you for authorization to complete repairs. After repairs are completed and the goods have been returned to you, Bullard will invoice you for actual work performed. Bullard Center 2421 Fortune Drive Lexington, KY 40509 · USA 877-BULLARD (285-5273) Tel: +1-859-234-6616 Fax: +1-859-246-0243 Americas: Europe: Bullard Asia-Pacific Pte. Ltd. E.D. Bullard Company Bullard GmbH 51 Changi Business Park 1898 Safety Way Cynthiana, KY 41031-9303 Toll free: 877-BULLARD (285- Dieselstrasse 8a 53424 Remagen · Germany Tel: +49-2642 999980 Central 2 #03-04 The Signature Singapore 486066 ISO 9001 certified 5273) Fax: +49-2642 9999829 Tel: +65 6745 0556 ©2024 Bullard. All rights reserved. Tel: 859-234-6616 Fax: 859-234-8987 www.bullard.com Bullard is a registered trademark of Bullard. 6081257976D (0124)