High-Quality Custom Window Coverings | Sun Glow
Instruction Manual for SUN GLOW models including: Roller Shade Savalan Window Decor, Savalan Window Decor, Window Decor, Decor
Installation Instructions | Open Roll | 202-04-29 www.mysunglow.com 2 of 4 3 INSTALL THE SHADE NOTE: For shades with Zero Gravity, please refer to Zero Gravity instructions on page 3 at this stage.
File Info : application/pdf, 4 Pages, 1.24MB
DocumentDocumentRoller Shade - Open Roll Installation Instructions WARNING STRANGULATION HAZARD -- Young children can be strangled by cords. Immediately remove this product if a cord longer than 22 cm or a loop exceeding 44 cm around becomes accessible. MISE EN GARDE RISQUE D'ÉTRANGLEMENT -- Les enfants en bas âge peuvent s'étrangler avec des cordes. Enlevez immédiatement ce produit si une corde mesurant plus de 22 cm devient accessible ou si le contour d'une boucle de plus de 44 cm devient accessible. 1 PREPARATION B C B C Component List A. Shade B. Universal Mounting Bracket C. Bracket Cover (Optional) D. Chain Tension Device A D 2 MOUNT THE BRACKETS Brackets are universal and are capable of receiving both the clutch and pin end. CEILING MOUNT WALL MOUNT LATERAL MOUNT Installation Instructions | Open Roll | 202-04-29 www.mysunglow.com 1 of 4 3 INSTALL THE SHADE NOTE: For shades with Zero Gravity, please refer to Zero Gravity instructions on page 3 at this stage. STEP 3A: INSTALL PIN END FIRST Put the spring loaded Pin End into the hole in the bracket. STEP 3B: INSTALL CLUTCH END Keeping gentle pressure against the Pin End lift the clutch up and align the two hooks on the clutch with the two slots in the bracket. The hooks should fall into place in the bracket, pull down gently to secure the blind into the bracket. **The bottom of the Clutch should point straight down. 4 INSTALL BRACKET COVERS (OPTIONAL) If you were supplied with bracket covers, install them by sliding them on to the mounting brackets. 5 INSTALL THE SAFETY SHIELD NOTE: For shades with chain operation only. Ensure that Safety Shield is carefully and properly installed. Installation Instructions | Open Roll | 202-04-29 www.mysunglow.com 2 of 4 Zero Gravity - Fascia or Open Roll Instructions These steps are not required for Zero Gravity in Curved Cassettes. Skip these steps if using chain, Neo, or motorized control If the Pin End of the shade appears as shown here, proceed with Steps 1,2 & 3 before returning to Step 4 of the Open Roll Installation Instructions If the Pin End of the shade appears as shown here, proceed with Steps 4,5 & 6 before returning to Step 4 of the Open Roll Installation Instructions 1 PREPARING FOR INSTALLATION NOTE: The blue shipping lock is used to lock the tension in place during shipping. Hex Plunger Remove shipping lock before installing 2 INSTALLING THE SYSTEM (A) Insert the pin end of the blind into the bracket. (B) Insert the hooked end into the other side bracket, and ensure the Zero Gravity head sits on the hooked teeth firmly. This should compress the hex plunger which releases the tension onto the shade. A B Push Push 3 TESTING THE SYSTEM Always operate the shade from the center of the bottom bar. Ensure that the shade is balanced and does not want to roll up or down on its own. If it does, then the spring will require more or less tension to be perfectly balanced. If the shade requires more tension, turn the zero gravity head into the fabric, ie opposite direction to the fall of the fabric. Insert for 5mm hex (only for outside mount) Adjusting Spanner Installation Instructions | Open Roll | 202-04-29 www.mysunglow.com 3 of 4 Zero Gravity Mini - Pin Lock Instructions These steps are not required for Zero Gravity in Curved Cassettes. Skip these steps if using chain, Neo, or motorized control WARNING · Do not pull pin lock out until shade is installed or tension will be released. · If tension has been released, see trouble shooting. 1 RUBBER BAND REMOVAL Before installing the shade remove the rubber band holding the Pin Lock in place. A B 2 INSTALL SHADE AND REMOVE PIN LOCK C D C: Install roller shade while keeping Pin Lock toward you and held in place. D: After installation remove the pin lock 3 TESTING THE INSTALLED ROLLER SHADE Installed roller shade must be operated smoothly by the centre of the bottom bar to avoid excessive telescoping TROUBLE SHOOTING: ONLY REQUIRED IF TENSION IS RELEASED If the tension is released or removed accidentally follow these instructions: The tension can be put back in any Zero Gravity Mini by turning the clutch head in the opposite direction of the fabric approximately 1 2 full rotations. While holding tension, insert the Pin Lock into the hole of the clutch. PROCEED WITH STEP 2 WHEN FINISHED. Installation Instructions | Open Roll | 202-04-29 www.mysunglow.com 4 of 4