User Guide for ESR models including: Digital Controller, 156.658, 156.658 Sunrise to Sunset Controller, 156.658, Sunrise to Sunset Controller, Sunset Controller
Digital Time Clock Operating Instructions: The digital timer has been programmed for testing purposes before you receive the unit. The Initial program has been set for Monday – Sunday with the ‘On’ time starting at 7.00am.
Automatic LED Light Sunrise to Sunset Controller
Digital Controller
The Automatic LED light sunrise to sunset controller has been designed for use with aviaries, fish tanks and reptile enclosures. It simulates the natural progression from day to night and from night to day to give your animals a more natural environment. The on and off times are easy to adjust and the rate of change from light to dark can also be adjusted to suit you and your animals requirements. The controller is supplied with a reel of `Daylight' LED tape (6000k). The tape is IP65 rate with 60 LED's per metre. The LED's are covered in epoxy resin to give them good protection from the elements. The tape is just 2.8mm deep and at 10mm wide, it will fit easily into many locations. Supplied on a 5 metre reel with a 3M self-adhesive back, this tape is easily applied to most smooth surfaces by simply removing the backing paper. The tape can be easily cut or joined, with cutting points at every 3rd LED (50mm) intervals. Highly flexible and versatile and with a low power consumption
SAFETY Thank you for choosing this product. Please read the manual thoroughly before using this equipment. If the unit was damaged in transit, do not install or use it and contact your dealer.
· Not Suitable for children under the age of 16 years · Children shall not play with the appliance · For indoor use only · Do not use in bathrooms, wet rooms or other damp locations · Do not operate equipment with wet hands to reduce the risk of electric shock · Do not use this appliance in locations where paint, petrol or other flammable liquids are used or stored · Please ensure the unit is switched off and unplugged when not in use · Do not use the appliance for other than its intended use · Do not use this product in close proximity to gas appliances · Periodically check this product for any signs of damage. If any damage is detected stop using it immediately and consult your supplier · Only install in well ventilated areas · There are no user serviceable parts in this product · Do not move or knock this product while in use · Do not overload. Maximum load is 4A (48W) · This product must only be used in an upright position · Do not cover · Do not use in areas with high concentrations of dust or fibre particles · Care should be taken when fitting this product
Included in the package
1 x 5 metre LED Tape 1 x 4 Amp Power Supply 1 x Automatic LED Dimmer 1 x DC Coupler 4 x Fixing Screws 1 x Pack of LED tape couplers (5) 156.658 1 x Instruction Manual
Installation
Installation must take place before the unit is plugged in.
1/ Install the LED Tape in a suitable position to give you maximum light coverage. The surface must be completely free of dust and grease. Note. The LED Tape can be cut at 50mm (3 LED's) intervals to the required length, highlighted by a line with a pair of scissors. This cut can be made with regular scissors (not supplied). If you need to join the LED Tape to negotiate corners and bends use the connectors provided or if you feel competent solder the joint. Once the final location has been established simply remove the self-adhesive backing on the rear of the tape and apply firm pressure along the length of the tape to ensure it has adhered in all locations
2/ If required you can mount the Automatic LED Sunrise to Sunset Controller to a wall with the fixing screws provided. Or it can be used as free standing unit on a shelf or table. Fit the DC RED Coupler to the DC power plug from the LED tape then connect it into the RED DC Socket located on the top of the case. You can now connect the power supply for the Automatic LED dimmer into the Black DC socket and plug the mains plug into a suitable socket outlet.
3/ It is recommended to leave the unit with power on for approximately 2 hours before setting the clock or altering the running times. This is to allow the battery in the timer module to charge.
4/ Set the clock on the Timer module. (See time clock operating instructions)
5/ The Automatic LED Sunrise to Sunset Controller will now run with the settings used to test the unit.
6/ If you wish to alter the `On' and `Off' times or the time from sunrise to sunset follow instruction for the dimmer module.
Digital Time Clock
Operating Instructions:
The digital timer has been programmed for testing purposes before you receive the unit. The Initial program has been set for Monday Sunday with the `On' time starting at 7.00am. The LED tape will start to come on and at 9.00pm the LED's will start to dim to `Off'. The dimming function has been for approximately 45 minutes, this and the clock can be adjusted to suit your own personal requirements.
D+ H+ M+
MANUAL
Press to access programming mode Press to select day
Press to increase hour
Press to increase minute
Press to set time Press to toggle between On, Off or Automatic
To alter the clock time or the On/Off times please follow these instructions. Setting the Clock:
Day
Press keep button pressed down, and then keep pressing D+ until the day you require appears on the top row of display. Hour
Press keep button pressed down, and then keep pressing H+ until the correct hour appears on the display (Note AM/PM indicator).
Minute Press keep button pressed down, and then keep pressing M+ until the correct minute appears on the display.
Programming Mode:
Press to enter programming mode. (Program 1) `On Time' Press H+ for hour you would like the light to start to come `on' followed by M+ for the minutes Press D+ to select one of the following options: (keep pressing for next option)
Optio n
1 2 3 4 5 6 7 8
9
10 11
12
13 14 15
Symbol
Mo Tu We Th Fr Sat Sun Mo, We, Fr
Tu, Th, Su
Sa, Sun Mo, Tu, Wed
Th, Fr, Sat
Mo, Tu, We, Th, Fr Mo, Tu, We, Th, Fr, Sa Mo, Tu,We,Th,Fr,Sa,Sun
Function
Only operates on Mondays Only operates on Tuesdays Only operates on Wednesdays Only operates on Thursdays Only operates on Fridays Only operates on Saturdays Only operates on Sundays Only operates on Mondays, Wednesdays and Fridays Only operates on Tuesdays, Thursdays and Sundays Only operates on Saturdays and Sundays Only operates on Mondays, Tuesdays and Wednedays Only operates on Thursdays, Fridays and Saturdays Only operates on week days Only operates on week days and Saturday Operates every day of the week {*}
Press again to program the Off (Program 1) Press H+ to select the hour followed by M+ for minutes to select the time you wish the light to start and dim off Press D+ to select one of the above options (if you require same option as don't press this button) To set up any of the other programs (2 20) repeat above procedure.
When finished press
Note: Timer will quit automatically if no buttons have been pressed within 10 seconds and no data will be saved.
Specifications:
LED Tape No LED's Colour Temperature (K) LED Tape 5 metre Cut Intervals IP Rating LED Type LED's per metre Power Supply
120 6000 2.8 x 10mm 50mm 65 5050 60 12Vdc
Dimmer Module Dimming Range Maximum Load
Time Clock Digital Time Range
Minimum Programming Timing Error Battery Back Up Power Failure Memory Mechanical Life Electrical Life Temperature Range Ambient Humidity
Power Supply
Dimensions Weight
1 second to 2 hours 4A (48 watts)
Quartz 7 day 24 hour ON/OFF programming 1 minute ± 2 sec/day @ 25°C Yes 3 Years 10,000,000 operations 100000 operations -10 to 50°C 35 to 85% RH
4 Amp 230Vac
125 x 175 x 125mm
Fixing Centres
Product Designed and Assembled in the UK Manufactured in Europe and Asia
This symbol on the device or the package indicates that disposal of the device after its lifecycle could harm the environment. Do not dispose of the unit (or batteries) as unsorted municipal waste; it should be taken to a specialized company for recycling.
This device should be returned to your distributor or to a local recycling service. Respect the local environmental rules. If in doubt, contact your local waste disposal authorities.
© COPYRIGHT NOTICE The copyright to this manual is owned by Logistic Technical Services. All worldwide rights reserved. No part of this manual may be copied, reproduced, translated or reduced to any electronic medium or otherwise without the prior written consent of the copyright holder.
Writer LibreOffice 24.8.4.2 (X86 64) / LibreOffice Community