Bio Bidet by Bemis - Bidet Seats, Attachments, Smart Toilets
Instruction Manual for DIB models including: 2293 Special Edition Advanced Bidet Toilet Seat, 2293, Special Edition Advanced Bidet Toilet Seat, Edition Advanced Bidet Toilet Seat, Bidet Toilet Seat
Bio Bidet | DIB Special Edition Advanced Bidet Toilet Seat
File Info : application/pdf, 20 Pages, 2.59MB
DocumentDocumentDIB Special Edition OWNER'S MANUAL 1 TABLE OF CONTENTS PRODUCT INFORMATION Safety Precautions...................................................4 Product Features.......................................................8 Unit & Parts..................................................................10 Dimensions...................................................................12 Remote Control.........................................................13 PRODUCT INSTALLATION Installation....................................................................14 Remote Control Installation.................................16 Trial Operation............................................................18 Product Disassembly...............................................19 Operation.....................................................................22 TROUBLESHOOTING Settings........................................................................30 Maintenance & Cleaning......................................34 Specifications............................................................36 Troubleshooting.......................................................37 Warranty.......................................................................38 2 3 SAFETY PRECAUTIONS PLEASE OBSERVE THE FOLLOWING PRECAUTIONS AND INSTRUCTIONS BEFORE INSTALLATION AND USE. · This product must be connected to a grounded 120V GFCI (ground fault circuit interrupt) outlet. Do not connect the power cord if it is damaged or broken. Do not plug the product into a loose electrical outlet. · It is recommended to use this product on a dedicated circuit. Sharing a dedicated circuit could cause the breaker to trip or lights to flicker. · If it is necessary to use an extension cord, use only a three-pronged extension cord plugged into a proper GFCI outlet. The marked rating of the extension cord should be equal to or greater than the electrical rating of the unit (10 amp). Consult a qualified electrician or service person if you are not sure whether the unit is properly grounded. · Do not open this product for repair without authorization from the manufacturer. Only qualified service personnel should service this product. Do not use accessories not recommended by the manufacturer. · Connect this product to a potable cold water supply line. · Close supervision is necessary when this product is used by children, eldely, or adults with sensitive skin. A low-temperature burn may occur when the skin has been in contact with an object at relatively low temperature for an extended period of time. · If using any chemical toilet bowl cleaner, be sure to wipe up any spills that splash onto the bidet. Do not use benzene or any acid chemical detergent, as they can cause discoloration. Only neutral detergents are permitted. · Do not plug in the power cord before connecting the water supply hose. · Install in an area with adequate ventilation to avoid high levels of humidity, which can damage the electronic components. · Do not touch the power cord with wet hands or reach for a product that has fallen into water. Unplug immediately. · Unplug the bidet seat when cleaning or detaching from the toilet bowl. · Do not plug in until plumbing work has been completed. · Keep the power cord away from heated surfaces to prevent a fire hazard. Keep any flammable materials away from this product at all times. 4 5 PRODUCT FEATURES DIB Bidet has the following characteristics: Continuous Warm Water Supply Enjoy continuous warm water throughout the wash cycle. Bubble Wash Aerated water wash adds cleaning comfort. Pulse & Oscillate Pulsating wash repeatedly cycles from weak to strong. Nozzle moves back and forth for massage effect. Energy Saving Function When activated, Energy Saving Mode will set the heaters to a lower temperature to reduce energy consumption. Touch Panel Remote Control Convenient touch screen remote control provides easy user interface. 6 Vortex Wash Soft but powerful water wash for added cleansing benefit. Stainless Steel Nozzle For better hygiene, a stainless steel nozzle is applied. Deodorization Function Deodorizing filter eliminates odors efficiently. Child Settings Optimized nozzle position and water pressure for children. User Preset User can preset and store the memory for control settings. 7 UNIT & PARTS 8 Mounting bolts Cone packing Mounting bracket Bolt guides Water supply hose (for toilet) Water supply hose (for bidet) Remote control Remote control AAA 4 batteries bracket 9 DIMENSIONS Elongated Round REMOTE CONTROL 10 11 INSTALLATION 1. Toilet Seat Removal 2. Turn Off Shut-Off Valve 5. Install Mounting Bracket 6. Slide Seat onto Plate · Lift hinge covers and use a screwdriver to remove the mounting bolts. · Remove the toilet seat. Steps may vary by type of seat. · Turn shut-off valve completely. · Flush toilet and hold down handle to completely empty tank. 3. Install T-Valve 4. Water Supply Hose Installation of T-valve Removal of water hose · Remove the existing water hose and then install T-valve to the bottom of the toilet tank. Ensure the rubber washer is properly seated and attach the original water hose to the T-Valve. 12 · Connect water supply hose for toilet. · Place adjustable mounting plate over mounting holes on toilet, flat side down, rubber side off mounting plate should be closet to the toilet tank. 7. Connect Bidet hose · Slide seat onto plate until it is secure and "clicks" into place. 8. Insert Deodorizing Cartridge · Connect bidet hose, making sure the hose is firmly connected. · Do not twist bidet hose, excessively bend it, or strip the plastic screw threads. 13 REMOTE CONTROL INSTALLATION 1. Remove Adhesive 2. Clean Area 5. Battery Life 6. Unplug If Unit Does Not Work · Remove the adhesive protection to attach the remote control bracket to the wall or other surfaces. · Clean the area thoroughly before attaching the bracket. 3. Batteries 4. Mount Remote (Optional) · Turn remove over and open the battery compartment. Inset four "AAA" type batteries (included) as indicated inside battery compartment and replace battery cover. 14 · Identify a location in the bathroom for the remote control that is visible and reachable from the toilet and mount remote using double stick tape (included). · When the batteries have reached the end of service life, all LEDs will blink. Replace the batteries with new AAA size (4pcs). · CAUTION - Do not use old and new batteries together. This could cause damage or failure of the remote control. · If the unit does not work after replacing the batteries, unplug and wait for 3 seconds. Plug in again. · After replacing the batteries, ID of the unit will be initialized as "00" and its ID will be equalized ID of the remote control that reaches the unit first. This ID assigning function will be needed to prevent signal interruption if more than 2 units are used at one place. In case of using one unit only, no setting is needed. 15 TRIAL OPERATION 1. Open Water Supply 2. Check For Leaks PRODUCT DISASSEMBLY 1. Unplug Power 2. Close Water Supply Valve · Open the water supply valve by turning it counterclockwise. 3. Nozzle · Check that there are no leaks around the hose connection. 4. Test · Unplug the power plug from the outlet. 3. Drain Water · Close the water supply valve by turning it clockwise. Completely drain out the toilet water tank, release the nuts at bidet body of the bidet hose, and then remove them from the main body. 4. Release & Remove · Be sure that the nozzle comes out and retracts when powered on. · Don't plug the power cord with wet hands. Risk of electric shock. 16 · Place your hand on the occupied sensor of the seat. The unit will fill with water. Check if water comes out from drain hold next to the nozzle for 1-2 seconds. · Press and release/drain button on the side of bidet. Completely drain the water out of the main body. While pressing the button, pull the main body forward and then remove it from the toilet. · Release the nuts, and then remove the brackets from the toilet. 17 PRODUCT DISASSEMBLY (CONT.) 5. Remove Bidet Hose 6. Connect Water Supply Hose · Remove the bidet hose, toilet hose and T-Valve. · Connect the water supply hose that was removed when the bidet was installed. 7. Open Water Supply Valve 8. Attach Toilet Seat · Open the water supply valve by turning it counterclockwise. · Attach the toilet seat and cover that were removed when the bidet was installed. 18 19 OPERATION 1. Sit On Toilet Seat 2. Press Posterior, Feminine, and Vortex Wash Buttons 3. Press Dry Button 4. Press STOP Button · Deodorization function starts automatically. · Selected function can be used as described. When selecting VORTEX WASH function, Oscillate function cannot be used). When selecting Child function, VORTEX WASH function may not operate). · Dib's specialized water spray in VORTEX WASH function enters into rectum, and then helps relieve constipation and fecal stasis. · Unless STOP button is pressed after Posterior and Feminine function, the dryer will start automatically. · Dryer temperature is adjustable. (5 levels) · Selected function may be used for up to 3 minutes. · Dryer effect will be improved if you wipe the moisture lightly before operating the drying function. · Selected functions stop. · Press STOP on the side control panel for 3 seconds to turn off the unit. 20 21 OPERATION (CONT.) 5. Wide Clean (Oscillation) 6. Massage (Pulse) 7. Water Pressure Control 8. Nozzle Position Control · When pressing the Wide Clean button during the operation of Posterior and Feminine, nozzle will move back and forth to wash a wider range. · When pressing the Child button during the operation of Wide Clean, the nozzle position can be adjusted in 5 positions. · Wide Clean function will not operate during the operation of Vortex wash. · When pressing Massage button during operation of Posterior, Feminine, and Vortex wash, water pressure will repeat high and low for smooth pulsating wash. · Adjust Water Pressure. · During the operation of Posterior, Feminine, and Vortex wash, nozzle position can be adjusted by pressing < or >. 22 23 OPERATION (CONT.) 9. Child Function 10. Seat Temperature Control · Press the Child button to activate. · Nozzle position will be one level move forward than normal. · Water pressure will be one level weaker than normal. · Seat temperature will be one level lower than normal. · Vortex wash will not operate while Child mode is activating. · Temperature of seat can be adjusted to the desired level by pressing Seat temp. button. · Room temp Low - Middle - High 24 11. Water Temperature Control · Temperature of water can be adjusted to the desired level by pressing Seat temp. Button. · Room temp Low - Middle - High 12. Energy Saving Modes Automatic Energy Save Mode · This mode will be activated by pressing the Energy Saving button until yellow LED lamp lights on. · Seat will be kept at 320C. Smart Energy Save Mode · This mode will be activated by pressing the Energy Saving button until green LED lights on. · Seat temperature will be kept at 320C when it is not occupied and raised back to preset level according to memorized time of use. · It may take 5-7 days to let the unit memorize the usage pattern. Cancel Energy Save Mode · Press the Energy Saving Button until LED is off to release the energy save modes. This unit adopts the instant heating technology for water heating and does not consume energy for water heating when it is in stand by mode. 25 OPERATION (CONT.) 13. Deodorizing Function · When sitting on the seat, deodorizing function starts automatically. · Speed of deodorizing fan can be controlled. (Refer to the User setting facilities). · After leaving the seat, the deodorizing function will operate for 1 additional minute. 14. Low Temperature Burn Protection · To reduce the chance of low temperature buns, the seat has a seat heater auto adjustment function which turns on low temperature (320C, 900F) when user sits on the seat for more than 15 minutes consecutively. 15. User Preset · Nozzle position, water pressure, dry/water/seat temperature can be present and stored for 2 different users. How to Preset 1. Adjust nozzle position, water pressure, dry/water/seat temperature to your preference. 2. Press the STOP button or wait. Red activating indicator will blink for 5 seconds when setting is completed. Using the Preset Feature 1. Press selected preset button 2. Preset nozzle position, water pressure, and temperatures will be activated. 26 27 SETTINGS User Setting With Remote Control Seat Switch `Off' Status Seat Switch `On' Status Regardless of On/Off Function Seat Status On/Off 1 Automatic Deodorizer Fan Switch Operation Press the "Stop" and "Energy Saving" for 3 seconds. Then adjust the fan speed by pressing "-" or "+" button. Leave the remote control alone for 5 seconds to complete the setting. Setting the ID of 2 Remote Control Press the "Wide Clean" button for 3 seconds. Then set the ID 0-3 by pressing "-" or "+". Leave the remote control alone for 5 seconds to set the ID. On/Off 3 Night Light Press "+" button for seconds. 28 Description Level Fan Speed Occu. Unocc. Display of activating indicator Energy saving (blinking) Initial Status default High 0 Off 1 Low High Off Low 2 Low High 3 High High Level default Display of activating indicator - 0 Blinking 1 Blinking 2 Blinking 3 Blinking Blinking Red Blinking Blinking Off Blue Blinking Purple Blinking Red Display of Seat temperature (blinking) Off Blue Purple Red High Speed in Both Modes ID "0" Night light can be turned on and off by pressing "+" button on the remote. Night Light is turned on 29 SETTINGS (CONT.) Extra Functions With Side Control Panel Seat Switch `Off' Status Seat Switch `On' Status Regardless of On/Off Function Manual 1 Nozzle Cleaning Seat Status Switch Operation Press "Posterior" for longer than 3 second Description Nozzle will move forward for cleaning 2 Power Off Press "STOP" Nozzle will retract and clean itself Factory 3 Default Setting Press "STOP" for longer than 5 seconds Press one of "Stop", "Posterior", or"Feminine" to power on Selecting/ 4 Canceling Silent Mode Press "Feminine" for longer than 3 seconds To on/off the chime sound. 30 Using Inline Carbon Filter Use of external water filter is only recommended in areas with known hard water issues. If a filter is used, it must be replaced every 3 months. This product is designed and intended for use exclusively with Bio Bidet DIB water filters. The purchase or use of any other water filter is not the responsibility of BBC Innovation LLC. As such, any use of non DIB water filters is prohibited and will void the warranty for those Bio Bidet products. Bio Bidet will not be responsible for any resulting damages or claims related to the misuse or distribution of non Bio Bidet DIB filters. 31 MAINTENANCE & CLEANING Manual Nozzle Cleaning Cleaning of Bidet Body Drain Remaining Water Maintenance During Winter 1. Press Posterior for longer than 3 seconds, and then nozzle will extract and stop (for 2 minutes). 2. Clean the nozzle with an unused toothbrush, etc., and press STOP. Nozzle will retract. 1. Exterior surface of bidet is made of plastic material, which may be damaged by scrubber, chemicals, etc. 2. Wipe the surface with a soft damp cloth. Do not spray water directly onto surface. 3. Clean the body after removing the power plug from the outlet. Be sure no water plashes onto the power plug or outlet. 4. Do not touch the power outlet with wet hands. Risk of electric shock. 1. Remove the power plug from the outlet. 2. Close the water feed valve by turning it counterclockwise. 3. Press the button on the side of the main body to drain the water. 1. Insert the power plug into the outlet and be sure if the power is supplied. 2. When the dib will not be used for a long time (more than a few days), close the water shut off valve and drain the water from the bidet. 32 33 SPECIFICATIONS ITEM Rated Voltage DIB-850 AC 120V, 60Hz Max. Consumption Power 1270W Power Cord Length 4ft. Water Feed Method Directly Connected to Water Pipe Water Pressure 9.95 - 106.7 psi Wash Posterior 0.16 gal/min Feeding Feminine Volume Vortex 0.16 gal/min 0.16 gal/min Water Pressure Control 5-Step Control Temp. Control Room Temp. ~ 1000F Heat Capacity 1200 W Safety Device Temp. Fuse, Thermo Switch Heated Seat Temp. Control Heater Capacity Room Temp. ~ 1070F 55W Safety Device Temp. Fuse Temp. Control Room Temp. ~ 1220F Dry Heater Capacity 250W Safety Device Temp. Fuse, Bi-metal Deodorization Catalytic Deodorization Product Dimension inch (mm) Elongated Round Product Weight/ Gross Weight lb (kg) Elongated Round 15.9" (406) x 20.8" (528) x 6.5" (165) 15.9" (406) x 19.5" (496) x 6.5" (165) 10.8 (4.9 kg)/17.4 (7.9 kg) 10.6 (4.9 kg)/17.2 (7.8 kg) 34 TROUBLESHOOTING Please check the following points before requesting the repair of the product. Problem Check List The bidet is not working Check if the power plug is not connected. Check for power failure. Water does not spray Water pressure is low Check if the water supply is suspended. Check if the water supply is suspended. Check if the nozzle is locked by foreign materials. Check if connection hose is bent. Check if the water pressure is set at too low level Water is not warm enough Check if its temperature is set at `off' or `low' Check if energy save mode is on. Seat is not warm enough Check if its temperature is set at `off' or `low' Check if energy save mode is on. Vortex wash is not operated Check if it is set on CHILD mode. Check if energy save mode is on. 35 WARRANTY 3 YEAR WARRANTY Bio Bidet warrants its products to be free from manufacturing defects under normal use and service for a period of 3 year from the date of purchase. This warranty is extended only to the original purchaser. For full warranty details, visit www.biobidet.com Contact Bio Bidet customer support with any questions you may have. 847.458.2334 support@biobidet.com www.biobidet.com 36 37 Thank You Technical Support/Customer Service 7900 S Route 31 Crystal Lake, IL 60014 T: 847.458.2334 U.S. TOLL FREE: 877.339.5214 support@biobidet.com www.biobidet.com