iDatalink - Home
Installation Guide for FIRSTECH models including: FTI-HDP8 Vehicle Coverage and Preparation, FTI-HDP8, Vehicle Coverage and Preparation, Coverage and Preparation, and Preparation, Preparation
FTI-HDP8 | MyFirstech Install
File Info : application/pdf, 3 Pages, 1.70MB
DocumentDocumentFTI-HDP8: Vehicle Coverage and Preparation Notes Make DL-HA6 Acura Model RDX PTS AT Year Install 2019-24 Type 1 CAN Blue Lights Park / Auto gray/blue BCM AFB Clutch S-NET Data BCM Gray 40-pin N/A Yellow Firmware: This installation requires BLADE-AL(DL)-HA6 firmware, flash module and update the controller firmware before installing. Lights: This kit includes a pre-terminated harness for the purpose of connecting the parking lights and clutch wire (when required). Use of the included harness requires modofocation of the gray I/O connector of the control module, removal of the existing parking light and status wires (the negative start wire also, when clutch handling is required), and replacing them with wires from the included harness. The required connections are located in the gray 28-pin connector, parking lights (pin #11), auto-lights (pin #10) S-Net: Gathering S-NET data requires a manual connection to be made at the Gray 40-pin connector of the BCM, the S-NET data wire is located at pin #35 of the connector. FTI-HDP8: Installation and Configuration Notes A REQUIRED CONNECTION B REQUIRED CONNECTIONS (SEE NOTES REGARDING REQUIRED MODIFICATION) C REQUIRED CONNECTIONS D NOT REQUIRED IIIIIIIIIIIIIIIIIIIIIIEIIIRIIIIIIIIIIIIIIIIIIIIIIIIIIIII D LAN 2001 O O Z K E R E D st. E IIIIIIIII S ID D KO O rG fo AD E R R E 'T T AN NC CE AND WHO O H W WANNA LEARN TO IIIIIIIII FEATURE COVERAGE CM7000/7200 Cut loop for A/T CM7X00 CM-900S/900AS CM900AS/900S Jumper IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII D O OTHER STUFF GOOD TOO IMMOBILIZER DATA A/M RS CONTROL DOOR LOCK DOOR UNLOCK ARM OEM ALARM DISARM OEM ALARM TRUNK/HATCH RELEASE DOOR STATUS TRUNK STATUS HOOD STATUS BRAKE STATUS E-BRAKE STATUS TACH OUTPUT AUTOLIGHT CTRL PARKING LIGHTS CM -900 FTI-HDP8 - DL-HA6 - Type 1 2019-24 Acura RDX PTS AT B BLADE PWR STATUS NOPCKOLINGNHETCSTION HDP8 2 1 OBD-II Connector 1 1 16 BCM 2 Blue Black Gray LED Programming Error Codes Module LED flashing RED during programming 1x - No CAN activity, check connectors/CAN voltage 2x - Klon data error, confirm S-NET connection 3x - No S-NET data, confirm connection 4x - No VIN, confirm CAN connections and vehicle entered when flashing ---------------------------After Klon: Solid red LED - redo part 1 of Klon 2x - Klon data is wrong, confirm data connection, start over from the beginnning 20 1 40 35 21 S-NET A PK LIGHTS ( - ) C AUTO LIGHTS N/C D 14 11 10 1 28 26 15 Takeover not supported: Vehicle engine will shut down when doors are opened. INSTALL GUIDE Page 40 of 41 Patent No. US 8,856,780 CA 2759622 COM-BLADE-AL(DL)-HA6-EN CARTRIDGE INSTALLATION 1 Slide cartridge into unit. Notice button under LED. 2 ALL IN ONE HONDA/ACURA Doc. No.: ##75672## 20210503 Ready for Module Programming Procedure. 1 2 OFF ACC ON START ENGINE START STOP 3 4 OFF ACC ON START ENGINE START STOP 5 6 MODULE PROGRAMMING PROCEDURE Close driver door. Re-open driver door to wake up data bus. Turn ignition to ON position. 7 8 OFF ACC ON START ENGINE START STOP WARNING: Do not press RS programming button. Connect power first. Connect RS to vehicle. Turn ignition to ON position. Wait, LED will flash BLUE rapidly. Turn ignition to OFF position. WARNING: Disconnect power last. Disconnect RS from vehicle. Connect RS to computer and proceed with extended programming. 9 Wait, LED will turn solid BLUE for 2 seconds . OFF ACC ON START 10 ENGINE START STOP 11 x1 Turn ignition to OFF position. Press UNLOCK on the OEM remote. ! If the vehicle is equipped with a power liftgate: Open and close the power liftgate with the OEM keyfob. 12 Module Programming Procedure completed. WWW.IDATALINK.COM Automotive Data Solutions Inc. © 2020