User Manuals: Happybuy Commercial Food Mixer & Mophorn Stainless Steel Work Table
Product 1: Happybuy Commercial Food Mixer
Model: B15B SERIES FOOD MIXERS
Main Specialty:
- The beater moves like planets in the bowls, ensuring complete food mixing according to the planet movement theory.
- Features three-range rotation speeds.
- All spare parts are made of premium stainless steel, meeting national hygiene standards for food.
- The machine is aesthetically pleasing, easy to operate, and highly efficient.
Technical Specifications:
| Model | Bowl Volume (L) | Voltage (V) | Rated Frequency (Hz) | Power (kW) | Max. Kneading Capacity(kg) | Mixing Speed (r/min) | Size(mm) |
|---|---|---|---|---|---|---|---|
| B15B | 15 | ~110 | 60 | 0.5 | 1.5 | 110/178/390 | 474×372×676 |
Operation and Notes:
- Before use, ensure the emergency stop button is released, the safety cover is closed, and the mixing bowl is in the right/highest position.
- Verify that the power supply matches the machine's requirements and that the external earthing wire is reliably connected.
- The 3-phase motor's rotation direction must be checked against the rotation mark. If incorrect, swap any two of the three livewires.
- Note: For testing, do not install mixing tools to prevent them from falling out due to incorrect rotation, which could damage machine parts.
Select Speed and Agitator:
- Dough arm: Best for heavy bread dough. Recommended flour-to-water ratio is approximately 47%-50% of the fill flour. Use at low speed.
- Beater: Suitable for thin batters, cakes, and mashing potatoes. Use at middle speed.
- Wire whip: Ideal for whipping cream and beating eggs. Use at high speed.
Important notice: Stop the machine before changing speed. Do not mix dough at middle or high speed.
Bowl Lift:
- To raise the bowl: Rotate the hand wheel until it touches the stop. This also makes the bowl more accessible for filling.
- To lower the bowl: Rotate the hand wheel to lower the bowl. Lowering the bowl is necessary for changing agitators or removing the bowl/agitators.
Note: When assembling an agitator, the bowl must be in the down position. Slip the agitator onto the shaft and turn until the driving pin engages the L-shaped slot in the agitator shank to prevent it from falling during operation.
Maintenance:
- After each use, clean the bowl and agitators thoroughly to keep the machine clear.
- Occasionally lubricate the bowl slide ways with a small amount of oil or grease using the tip of a finger.
Troubleshooting:
| Trouble | Probable Cause | Remedy |
|---|---|---|
| The mixing shaft doesn't rotate after switch on | Electric connectors are loose | Check the electric circuit and tighten loose connectors. |
| Oil leakage | Oil seals are worn out | Replace those oil seals. |
| Guide ways are corroded | Clean and oil the guide ways. | |
| The raising handle is too tight | The lead screw, bevel gear, and hand wheel shaft etc. is dry | Oil them. |
| Lack of voltage | Check the supply voltage. | |
| Temperature rise of motor is too high, below speed | Over load | Reduce the load. |
| The working speed selected is too high or agitator is not suitable | Select a suitable speed and agitator. | |
| The noise of the gearbox is serious, its temperature is too high | Lubrication is insufficient | Add or replace the oil. |
| The agitator knocks with the bowl | The agitator or the bowl is deformed | Repair or replace the deformed part. |
| Unable to open the machine | Cover opened, bowl lifted down or emergency stop button opened | Close the safety cover, lift the bowl up, and release the emergency stop button. |
Product 2: Mophorn Stainless Steel Work Table
Description: Stainless Steel Work Table with Wheels, 24 x 30 x 32 Inch Prep Table with 4 Casters, Heavy Duty Work Table for Commercial Kitchen Restaurant Business.
Assembly Instructions:
The following steps describe the assembly of the Mophorn Stainless Steel Work Table:
- Step 1: Identify all parts. This includes the tabletop (a), lower shelf (b), legs, casters, and hardware (screws, nuts, washers).
- Step 2: Attach the casters to the bottom of the legs. Ensure they are securely fastened.
- Step 3: Attach the legs to the underside of the tabletop. Use the provided screws and nuts.
- Step 4: Attach the lower shelf to the legs. Align the shelf with the pre-drilled holes on the legs and secure with hardware.
- Step 5: Once assembled, the work table with wheels is ready for use.
Visual Description of Assembly Steps:
- Image 1: Shows all the components laid out: tabletop, lower shelf, legs, casters, and various hardware pieces labeled 'a' and 'b'.
- Image 2: Illustrates attaching the legs to the tabletop, with a close-up showing how the hardware (b) connects the leg to the tabletop.
- Image 3: Depicts attaching the lower shelf to the legs, with a close-up showing the connection point and hardware.
- Image 4: Shows the attachment of the casters to the legs.
- Image 5: Presents the fully assembled stainless steel work table with wheels.