User Manual for BLUETTI models including: EB200P, 2AYT3-EB200P, 2AYT3EB200P, EB200P Portable Power Station, Portable Power Station, Power Station
SHENZHEN POWEROAK NEWENER CO., LTD EB200P Portable Power Station 2AYT3-EB200P 2AYT3EB200P eb200p
2 days ago — 06 USB-A 5V/3A output x 2pcs. Classic USB-A ports. Page 8. 6. LET`S GET STARTED. (1) Startup: short press the power button, the indicator light is on, and the ...
File Info : application/pdf, 20 Pages, 3.19MB
DocumentDocumentPlease read this manual before use and follow its guidance. Keep this manual for future reference. Please read this manual before use and follow its guidance. Keep this manual for future reference. CONTENTS 1. BRIEF INTRODUCTION......................................................................... 01 2. ABBREVIATION...................................................................................... 01 3. SAFETY INSTRUCTION .........................................................................01 4. IN THE BOX............................................................................................02 5. FUNCTIONS........................................................................................... 04 6. LET`S GET STARTED............................................................................ 05 7. TOUCHSCREEN OPERATION............... ..............................................05 8. CHARGIN G .............................................................................................08 9. DISCHARGING....................................................................................... 11 10. APPLICATION SCENARIO ....................................................................11 11. EXAMPLES OF LOADS ........................................................................ 11 12. ESTIMATION OF OPERATING TIME ................................................... 12 13. TECHNICAL SPECIFICATIONS ........................................................... 13 14. TROUBLESHOOTINGS........................................................................14 15. FAQ (Frequently Asked Questions) .......................................................15 16. DECLARATION.....................................................................................16 1.BRIEF INTRODUCTION The EB200P features continuous output power at 2,200W from the pure sine wave inverter and a built-in unique 30A NEMA TT-30 receptacle designed for the RV,and 100W PD3.0 USB-C port, 900W MPPT controller are all integrated. 2.ABBREVIATION be automatically turned off if the load on it is less than 50W over a span of 4 hours. 3.SAFETY INSTRUCTION ment in an environment with flammable, explosive gas, or smoke. It is also prohibited to operate the equipment in this environment. ment by anyone other than authorized electrician. dry completely before using. poor connections to the hardware inside. as a household wall outlet. Please use it carefully and keep children away from it. - 01 - For safety purposes, please use only the original charger and cables designed for the equipment. We are not liable for damage caused by third-party equipment and may render your warranty invalid. 4. IN THE BOX No. Picture Standard Accessories Category 1 Power Station(EB200P) Quantity 1PCS 2 T500 500W Adapter For AC charging 1PCS 3 PV Charging Cable (XT90 - MC4) 1PCS For solar charging, up to 15A,900W. Car Charging Cable 4 (XT90 - Cigarette Lighter Port) 1PCS Charge EB200P by car. 5 Multi-functional Aviation Cable (XT90 - Aviation) Expand the charging methods via PV input port. 1PCS User Manual 6 Please read the manual before use and follow its guidance, 1PCS keep this manual for future reference. 7 Warranty Card Please keep this Warranty Card properly. 1PCS 8 Certificate of QC PASS 1PCS - 02 - No. Picture 9 10 11 12 Optional Accessories Category Lead-acid Battery Charging Clamp Charging EB200P through lead-acid battery only. DO NOT charge the lead-acid battery via this cable. Multi-functional Input Cable (XT90 - DC7909) Expand the charging methods via AC input port. 12V/30A Output Bundle (Aviation - XT60, XT60 - SPC45) Perfect for RV. XT60 to Anderson Plug (Output) Type Optional Input Cable Optional Output Accessories D300S PV Step Down Module 13 Step down the voltage of solar panels(especially rigid panels) to adapt to Optional Accessories EB200P solar input limit range. - 03 - 5. FUNCTIONS 09 01 02 10 03 11 04 05 12 06 07 08 01 DC 12V/10A cigarette lighter port Output port for devices with corresponding plug such as vehicle-use vacuum, refrigerator. 08 AC input port Charging via T500 adapter. 02 DC 5521 12V/10A output x 2pcs Traditional ports for routers/cameras, old laptop etc. 03 DC 12V/30A output Special 30A output port can be adapted to appliances widely,perfect for RV. 04 USB-A 18W output x 2pcs Quick charge USB-A ports. 05 USB-C 100W output Can be used via USB-C to USB-C cable to charge most devices in the market such as Pixel Phone, Macbook Pro at 100W Max. 09 Wireless charging 15W x 2pcs Place your phone(if wireless charging supported) on the top of the EB200P vertically, and turn on the DC in mainpage on screen. 10 Touchable interaction LCD display Can be pressed/tapped to control the unit by nails. 11 Power button Lone/Short press to turn ON/OFF the EB200P. 06 USB-A 5V/3A output x 2pcs Classic USB-A ports. 07 DC input port Can be connected to solar panels, or achieving car charging, lead-acid battery, extra T500 adapter by extra cables. 12 US AC output x 6 pcs (EU/UK AC output x 4pcs) Standard AC receptacle: wildly used in 100-120V areas, generates the almost same AC power as a household wall outlet. High-voltage area uses special sockets. - 04 - 6. LET`S GET STARTED (1) Startup: short press the power button, the indicator light is on, and the machine is in standby mode. (2) Shutdown: press and hold the power button for more than 2 seconds, and the indicator light will be off and the machine shut off. The LED indicator lamp status warning BMS Over current or short circuit protection Turn off after the indicator light flashes BMS Startup timeout The indicator light flashes and not shut down Normal startup The indicator light on Normal shutdown The indicator light off (3) DC power switch and AC power switch are integrated in the interaction LCD screen(Figure 1),press"DC ON/OFF"button and "AC ON/OFF"button on the screen to turn on/off the DC /AC output. 7. TOUCHSCREEN Interaction LCD screen(Information Vision) supports below functions: Real time display of voltage, current, power, temperature and state of charge and discharge. consumption mode and time information according to the setting column. Support energy-saving, and enable Super ECO mode to save more than 30% of useless energy loss. Support users to view fault information, historical fault information, software version independently. - 05 - Warm tip: touch button by fingernail lightly until it "beeps". on it. (1) When press the power button,it will enter the main interface of the LCD display screen: (Mainpage) ((Figure 1)) a.PV/Car charging display b.BMS Info c.Date/Time d.DC load Info e.DC ON/OFF Switch f. AC ON/OFF Switch g.Adapter charging display h.AC load Info (2) Click the settings button in the main interface (Figure 2) to enter the setting interface as follows (Figure 3) : Warm tip: Please enter the setting interface to set the date and time according to the local time zone, and check the output voltage, frequency and other parameters for the first time. Voltage and Frequency Reference: EU output: 230V/50Hz UK output: 230V/50Hz DC Input Source: Select the right method you choose to charge EB200P. ECO Mode: While it`s on, the AC output ports will be automatically turned off if the load on it is less than 50W over 4 hours. Press "Next" icon to enter date setting as (Figure 3): Backlight and Sleep time: set the proper value as your need for power saving. Date and time: 2000-00-00 00 00 00, tap the number to set it right. - 06 - Figure 2 Figure 3 (3)Return to the mainpage, tap the "Data" icon to enter the Data page (Figure 4) : Tap the "Product Info" icon, you can view the product model, software version, BMS version etc; which can also be accessed directly from the shortcut icon on the mainpage; Tap the "BMS Maintenance" icon to view the status of battery, and it can also be accessed directly from the shortcut icon in the mainpage; Tap the "Fault History" icon, all the fault information generated by the EB200P in daily use. Figure 4 (4) Tap Alarm Icon (mainpage) to view the current error information: the fault indicator will display orange if there is a fault occurs. - 07 - 8. CHARGING (1) From AC Wall outlet Turn EB200P ON and connect the plug of adapter to the wall outlet, the other side to AC input port. Charging will automatically stop when it reaches 100% (4.6-5.1Hrs). AC socket AC-DC adapter (2) From the solar panels Connect the solar panels(in series or parallel) with Open Circuit Voltage range 10V-145V. Connect the solar panel to EB200P via solar charging cable. (Standard Accessories 5 to Accessories 3) Plug and play charging: EB200P will be activated when solar charging system built up successfully. Max input current of the solar charging: 15.2A ± 0.3. MC4 Connecting 3 XT90 Plug Aviation Plug - 08 - (3) Car Charging Press the power button and connect it to the cigarette lighter port through the car charging cable. Enter the setting interface as shown in (Figure2) through the display screen to set DC input source to car mode; The product can be charged with 8.2A maximum current. (4) Generator Charging(gasoline, propane or diesel) Connect the AC adapter input to the generator and the output port to the AC charging port of the machine. Press the power button, the product will be charged, the charging will automati- cally stop when it reaches 100%. (5) Lead-acid Battery Charging Connect to the positive and negative poles of the battery through the Charging Clamp (Accessories 9) Note: pay attention to distinguish the positive and negative poles of the battery, the red side indicates positive pole. Enter the setting interface in (Figure 1) through the screen to set DC input source to "car mode" to achieve 12V/24V car charging mode, with the maximum current of 8.2A. Note: DO NOT charge the battery through this accessory. - 09 - 9 (6) Dual Charging Set the DC input source to PV to achieve AC + PV Dual Charging Set the DC input source to others to achieve AC + T500/Lead-Acid Battery Charging. - 10 - 9. DISCHARGING 10. APPLICATION SCENARIO 11. EXAMPLES OF LOADS - 11 - 12. ESTIMATION OF OPERATING TIME Smartphone 165-200Times 10W LED Light Bulb Around 75-85hrs 20W Television Around 21-23hrs 75W Electronic Tools Around 19-21hrs 80W Refrigerator Around 17-19hrs 90W Slow Cooker Around 7-9hrs 200W - 12 - 13. TECHNICAL SPECIFICATIONS Dimensions Charging Temperature Discharge Temperature Working Humidity Working Noise 5-12VDC, 5VDC,3A 3A, 15W Total 18Wx2 AC-DC Adapter 58.8VDC,8A Solar Charging 10V-145VDC/15A Car Charging Battery Charging 11-28.8VDC/8.2A - 13 - 14. TROUBLESHOOTINGS - 14 - 15. FAQ (Frequently Asked Questions) - 15 - 16. DECLARATION - 16 - Company: Address: Mail: Company: Address: Mail: P/N:17.0303.0375-00A0Microsoft: Print To PDF