CONGRATULATIONS ON YOUR PURCHASE

Better Bathrooms aims to provide extraordinary bathroom products at affordable prices. Whether you prefer a modern, traditional, or unique style, Better Bathrooms offers fittings and fixtures to bring your ideas to life.

If you encounter any issues with your new product, Better Bathrooms is available to assist.

• Contact their UK call centre at 0871 244 0935 (Monday-Friday, 9:00 AM - 4:30 PM; Saturday, 9:00 AM - 2:00 PM).
• Send a message via betterbathrooms.com.

SAFETY

• Installation should be performed by a qualified electrician.
• The fitting is suitable for connection to a 220-240V earthed supply, adhering to current IEE wiring regulations and local Building Regulations.
• This product is intended for domestic, indoor use only.
• Connection should be to a dedicated lighting circuit protected by a 5-amp fuse or a 6-amp miniature circuit breaker.
• Ensure adequate distance between the electrical connection and the mirror casing to prevent shorting.
• Before installation, switch off the mains supply and remove the appropriate fuse or circuit breaker. Take precautions to prevent accidental reconnection.
• Do not place flammable materials within the indicated "Minimum Distance" from the unit.
• Handle the product with care, as it may contain delicate parts prone to breakage.
• Keep the shaver socket cover closed when not in use to prevent moisture ingress.
• Only use items designed for shaver sockets, such as shavers or electric toothbrushes.
• The shaver socket provides 230V at a maximum current of 80mA and is not earthed. Do not connect devices requiring higher current, different voltage, or an earth connection.
• Modifications to the fitting will void the warranty and may render the product unsafe.
• Do not operate a defective or damaged appliance, as it may cause electric shock. Disconnect from mains before seeking assistance.
• The product is IP44 rated. Installation is permitted in Bathroom Zone 2 only; not in Zones 0 or 1.
• Ensure no pipes or wires are located behind the wall before drilling.
• Clearly mark the hanging location to avoid wall damage due to incorrect positioning.
• Inspect the mirror for damage before installation.
• Unpack carefully, avoiding sharp blades to prevent mirror damage and warranty voidance.
• Apply a bead of silicone sealant between the mirror and the wall along the top and sides. Do not seal the bottom to prevent water accumulation behind the mirror.

BATHROOM ZONES

The diagram illustrates bathroom zones for electrical safety:

• Zone 0: The interior of the bathtub or shower basin.
• Zone 1: The area around the bathtub or shower basin up to a height of 2.25m above the floor.
• Zone 2: The area extending 0.6m outside the bath or shower and above the bath or shower if over 2.25m.

PARTS SUPPLIED

• WALL PLUGS (x2)
• SCREWS M4 (x2)

Note: Installers are responsible for ensuring supplied fittings are suitable for the wall type. Alternative fittings may be required and are not supplied. Seek professional advice if unsure.

TOOLS REQUIRED

• TAPE MEASURE
• SPIRIT LEVEL
• ELECTRIC DRILL
• SCREWDRIVER
• HAMMER
• 8mm DRILL BIT
• PENCIL

HANGING THE MIRROR

The mirror can be hung in landscape or portrait orientation. It features four keyholes on the back: two on the vertical side and two on the horizontal side.

1. Ensure the power is disconnected at the circuit breaker and cannot be reconnected during installation.
2. Measure the distance between the two keyholes.
3. Mark the positions of the keyholes on the wall, using a spirit level to ensure they are level.
4. Drill two holes into the wall at the marked positions using a suitable drill bit.
5. Insert the wall plugs into the holes.
6. Insert the screws into the wall plugs, leaving approximately 3mm of the screw head protruding.
7. Check that the screws align correctly and that the mirror can be hung securely.
8. Connect the mirror to a suitable fuse spur, following current regulations and guidance. Ensure sufficient cable length for safe removal.
9. Carefully hang the mirror onto the screws, ensuring it is secure and will not slide.
10. Reconnect the power supply.

Wiring Diagram:

LUMINAIRE input wiring diagram

• Brown/black (live)
• Yellow/green/green (earth)
• Blue/white (neutral)

MAINS SUPPLY

• Brown/red/black (live)
• Yellow/green/green (earth)
• Blue/black/white (neutral)

OPERATION

• Lights & Demister: Press the button once to turn on the lights and activate the de-misting function.
• Colour Temperature: Hold the button to cycle through colour temperatures from 3000K (Warm White) to 6000K (Cool White).
• Turn Off: Press the button again to turn off the lights and demister.

BLUETOOTH PAIRING

To pair your phone with the Bluetooth speaker system:

1. Press the Bluetooth symbol to initiate pairing.
2. Access your phone's Bluetooth settings. A list of available devices will be displayed.
3. Locate and select "Mirror-BT".
4. Your phone is now paired to the speakers. To exit pairing, disconnect via your phone or press the Bluetooth button on the mirror.

SHAVER SOCKET

The mirror features a shaver socket on its underside, next to the speakers. This socket is designed exclusively for shavers and other low-voltage items compatible with a shaver socket.

The shaver socket is ready for use once the mirror is connected to the mains power.

CLEANING AND MAINTENANCE

• Avoid using cleaning products containing bleach or abrasive cleaners, as they can damage the mirror's appearance and lifespan.
• Clean the mirror with a clean microfiber cloth.

TECHNICAL SPECIFICATION

DISPOSAL

Recycling facilities are available for old electrical products. Customers can deposit old electrical equipment at participating sites managed by local councils.

Please be considerate during the recycling process. Contact your local council for details on household waste recycling centers.

At the time of printing, the product does not contain substances listed in Annex XIV of the REACH Regulations (EC) 1907/2006. In accordance with Article 59 of the same regulation, Cadmium is present at permitted levels.

Better Bathrooms monitors regulations to ensure continued compliance. Further information is available upon request.