Winston Porter Large Coffee Bar Cabinet Assembly Instructions

Product Overview

This document provides detailed, step-by-step instructions for assembling the Winston Porter Large Coffee Bar Cabinet. Please review all instructions, parts, and hardware carefully before beginning assembly. For optimal results and safety, assembly by two adults is recommended.

Parts List

Hardware List

Assembly Steps

Step 1: Prepare Slide Rails

Separate the slide rail set (E) into components E1 and E2. This process should be repeated for all four sets.

Diagram Description: A slide rail assembly (E) is shown being divided into two parts, E1 and E2. This action is performed four times.

Step 2: Assemble Side Panel to Support

Install two Cam Bolts (B) into Part #5. Attach Part #5 to Part #3 using two Dowels (A). Secure the connection by installing and turning two Nuts (C).

Diagram Description: Two Cam Bolts (B) are inserted into Part #5. Part #5 is then joined to Part #3 using two Dowels (A). Two Nuts (C) are tightened to secure the assembly. Quantities: B x2, A x2, C x2.

Step 3: Install Cam Bolts

Install two Cam Bolts (B) into Part #9.

Diagram Description: Two Cam Bolts (B) are shown being inserted into designated holes on Part #9. Quantity: B x2.

Step 4: Attach Slide Rail to Side Panel

Install one Rail E1 to Part #9 using two Screws (H). Ensure the rail is oriented correctly.

Diagram Description: A slide rail component (E1) is attached to Part #9 using two Screws (H). An arrow indicates the correct orientation. Quantities: E1 x1, H x2.

Step 5: Join Panels

Attach Part #3 to Part #9 using two Dowels (A). Secure the connection by installing and turning two Nuts (C).

Diagram Description: Part #3 is connected to Part #9 via two Dowels (A). Two Nuts (C) are tightened to fasten the parts together. Quantities: A x2, C x2. A note indicates that plates 3 and 9 may need to be held by hand while tightening screws.

Step 6: Install Cam Bolts

Install five Cam Bolts (B) into Parts #10 and #11.

Diagram Description: Five Cam Bolts (B) are shown being inserted into designated holes on Parts #10 and #11. Quantity: B x5.

Step 7: Connect Panels

Attach Part #11 to Part #10 using two Dowels (A). Secure the connection by installing and turning three Nuts (C).

Diagram Description: Part #11 is joined to Part #10 using two Dowels (A). Three Nuts (C) are tightened to fasten the parts. Quantities: A x2, C x3.

Step 8: Attach Brackets and Supports

Attach Part #12 and two of Part #22 to Part #10 using six Screws (M).

Diagram Description: Part #12 and two Corner Brackets (Part #22) are attached to Part #10 using six Screws (M). Quantities: M x6.

Step 9: Attach Slide Rail

Install one Rail E1 to Part #12 using two Screws (H). Ensure the rail is oriented correctly.

Diagram Description: A slide rail component (E1) is attached to Part #12 using two Screws (H). An arrow indicates the correct orientation. Quantities: E1 x1, H x2.

Step 10: Join Panels

Attach Part #10 to Part #3 using two Dowels (A). Secure the connection by installing and turning two Nuts (C).

Diagram Description: Part #10 is connected to Part #3 via two Dowels (A). Two Nuts (C) are tightened to fasten the parts together. Quantities: A x2, C x2. A 90-degree angle is indicated.

Step 11: Prepare Panels and Attach Bracket

Install two Cam Bolts (B) into Part #5. Attach Bracket (P) to Part #4 using six Screws (F).

Diagram Description: Two Cam Bolts (B) are inserted into Part #5. A Bracket (P) is attached to Part #4 using six Screws (F). A note indicates to tighten screws to 80% first, then fully tighten all once aligned. Quantities: B x2, P x1, F x6.

Step 12: Join Panels

Attach Part #5 to Part #4 using two Dowels (A). Secure the connection by installing and turning two Nuts (C).

Diagram Description: Part #5 is connected to Part #4 via two Dowels (A). Two Nuts (C) are tightened to fasten the parts together. Quantities: A x2, C x2. A 90-degree angle is indicated.

Step 13: Install Cam Bolts

Install five Cam Bolts (B) into Parts #7 and #11.

Diagram Description: Five Cam Bolts (B) are shown being inserted into designated holes on Parts #7 and #11. Quantity: B x5.

Step 14: Connect Panels

Attach Part #11 to Part #7 using two Dowels (A). Secure the connection by installing and turning three Nuts (C).

Diagram Description: Part #11 is joined to Part #7 using two Dowels (A). Three Nuts (C) are tightened to fasten the parts. Quantities: A x2, C x3.

Step 15: Attach Brackets and Supports

Attach Part #12 and two of Part #22 to Part #7 using six Screws (M).

Diagram Description: Part #12 and two Corner Brackets (Part #22) are attached to Part #7 using six Screws (M). Quantities: M x6.

Step 16: Attach Slide Rail

Install one Rail E1 to Part #12 using two Screws (H). Ensure the rail is oriented correctly.

Diagram Description: A slide rail component (E1) is attached to Part #12 using two Screws (H). An arrow indicates the correct orientation. Quantities: E1 x1, H x2.

Step 17: Join Panels

Attach Part #4 to Part #7 using two Dowels (A). Secure the connection by installing and turning two Nuts (C).

Diagram Description: Part #4 is connected to Part #7 via two Dowels (A). Two Nuts (C) are tightened to fasten the parts together. Quantities: A x2, C x2. A note indicates that plates 4 and 7 may need to be held by hand while tightening screws.

Step 18: Install Cam Bolts

Install two Cam Bolts (B) into Part #8.

Diagram Description: Two Cam Bolts (B) are shown being inserted into designated holes on Part #8. Quantity: B x2.

Step 19: Attach Slide Rail

Install one Rail E1 to Part #8 using two Screws (H). Ensure the rail is oriented correctly.

Diagram Description: A slide rail component (E1) is attached to Part #8 using two Screws (H). An arrow indicates the correct orientation. Quantities: E1 x1, H x2.

Step 20: Join Panels

Attach Part #8 to Part #4 using two Dowels (A). Secure the connection by installing and turning two Nuts (C).

Diagram Description: Part #8 is connected to Part #4 via two Dowels (A). Two Nuts (C) are tightened to fasten the parts together. Quantities: A x2, C x2. A 90-degree angle is indicated.

Step 21: Attach Side Panels

Attach Part #2 to Parts #7, #8, #9, and #10 using eight Dowels (A) and eight Screws (D).

Diagram Description: Part #2 is attached to the assembled structure (Parts #7, #8, #9, #10) using eight Dowels (A) and eight Screws (D). A note indicates that the groove on Part #2 should be on the reverse side. Quantities: A x8, D x8.

Step 22: Install Adjustable Feet

Install six Adjustable Feet (O) to Part #2 using eighteen Screws (F).

Diagram Description: Six Adjustable Feet (O) are attached to the bottom of Part #2 using eighteen Screws (F). A note states that it takes two people to spin the unit at the same time. Quantities: O x6, F x18.

Step 23: Attach Back Panels

Attach Back Panel #19 to Part #7&8. Attach Back Panel #20 to Part #8&9. Attach Back Panel #21 to Part #9&10.

Diagram Description: Three back panels are shown being attached to the main cabinet structure. Panel #19 connects to #7&#8, Panel #20 connects to #8&#9, and Panel #21 connects to #9 . A note mentions that the cable hole position on Part #20 can be adjusted according to the refrigerator's cable position. A 180-degree rotation is indicated, and two people are recommended for this step.

Step 24: Install Cam Bolts

Install eight Cam Bolts (B) into Part #1.

Diagram Description: Eight Cam Bolts (B) are shown being inserted into designated holes on Part #1. Quantity: B x8.

Step 25: Attach Top Panel

Attach Part #1 to Parts #7, #8, #9, and #10 using eight Dowels (A). Secure the connection by installing and turning eight Nuts (C).

Diagram Description: Part #1 (Top Panel) is attached to the main cabinet structure (Parts #7, #8, #9, #10) using eight Dowels (A). Eight Nuts (C) are tightened to fasten the parts. Quantities: A x8, C x8. A warning icon indicates caution with fingers.

Step 26: Install Power Outlets

Install one Power Outlet (J) to Part #1 using two Screws (H).

Diagram Description: A Power Outlet (J) is attached to Part #1 using two Screws (H). Quantities: J x1, H x2.

Step 27: Install Back Buckles

Install eighteen Back Buckles (N) to the backside of Parts #19, #20, and #21 using eighteen Screws (N). This step enhances product stability.

Diagram Description: Eighteen Back Buckles (N) are attached to the rear panels (#19, #20, #21) using eighteen Screws (N). Quantities: N x18.

Step 28: Lock Back Panel to Wall

Secure the strip (Q) to Part #1 using the short screw (Q) as shown. Wait for the back to lock to the wall.

Diagram Description: A strip (Q) is attached to the cabinet (Part #1) using a screw (Q). This is part of the wall anchoring system. Quantities: Q x2.

Step 29: Install Slide Rails

Install two Rails E2 to Parts #14 and #15 using four Screws (H) for each rail. Repeat this process twice.

Diagram Description: Two Rail E2 components are attached to Part #14 and Part #15 respectively, using four Screws (H) per rail. The process is repeated for the second set of drawer sides. Quantities: E2 x4, H x8. A note indicates to observe the direction of the slot on the rail.

Step 30: Assemble Drawer Sides

Attach Parts #14 and #15 to Part #16 using four Screws (L) for each connection. Repeat this process twice.

Diagram Description: Drawer Side Panels (#14 and #15) are attached to a Drawer Back Panel (#16) using four Screws (L) per side. This is repeated for the second drawer. Quantities: L x8.

Step 31: Attach Drawer Bottom Panel

Attach the Drawer Bottom Panel (Part #17) to the assembled drawer unit from Step 30. Repeat this process twice.

Diagram Description: Drawer Bottom Panel (Part #17) is inserted into the assembled drawer frame (from Step 30). This is done for both drawers.

Step 32: Install Cam Bolts

Install four Cam Bolts (B) into Part #13. Repeat this process twice.

Diagram Description: Four Cam Bolts (B) are shown being inserted into designated holes on Part #13. This is repeated for a second Part #13. Quantity: B x8.

Step 33: Connect Drawer Fronts

Connect Part #13 to Parts #14 and #15. Install and turn four Nuts (C) to secure the position. Repeat this process twice.

Diagram Description: Drawer Front Panel (Part #13) is connected to the assembled drawer sides (#14, #15) using Cam Bolts (B) and secured with four Nuts (C). A note indicates the hypotenuse should be on a specific side. This is repeated for the second drawer. Quantities: C x8.

Step 34: Install Drawers

Attach the two assembled drawers to the cabinet as shown.

Diagram Description: The two completed drawers are shown being inserted into the cabinet structure. A note explains that a screw (H) can be loosened to adjust drawer gaps. Quantities: H x4.

Step 35: Install Hinges

Install two Hinges (I) to Part #18 using four Screws (H) for each hinge. Repeat this process twice.

Diagram Description: Two Hinges (I) are attached to Part #18 using four Screws (H) per hinge. This is repeated for the second Part #18. Quantities: I x4, H x8.

Step 36: Attach Doors

Attach Part #18 (with hinges) to Parts #7 and #10 using sixteen Screws (H).

Diagram Description: The doors (Part #18 with attached hinges) are mounted onto the cabinet frame (Parts #7 and #10) using sixteen Screws (H). The diagram shows adjustment screws on the hinges for fine-tuning door alignment (up/down, left/right, front/back). Quantities: H x16.

Step 37: Install Door Handles

Install two Handles (G) to Part #18 using four Screws (H) for each handle.

Diagram Description: Two Handles (G) are attached to the doors (Part #18) using four Screws (H) per handle. Quantities: G x2, H x4.

Step 38: Insert Shelves

Place eight Adjustable Pegs (K) at your desired height level and insert Shelf Part #6 into the cabinet.

Diagram Description: Eight Adjustable Pegs (K) are inserted into the cabinet's interior holes at the desired shelf height. Shelf Part #6 is then placed onto these pegs. The diagram shows how the pegs should be inserted (rotary press into hole). Quantities: K x8.

Step 39: Wall Anchoring Preparation

The cabinet must be permanently fixed to the wall with the included anti-tipping device to prevent tipping over. Mark the drill position on the wall with a pencil. Drill holes at the marked positions using a bit. Gently insert the wall anchor (Q) into the drilled hole with the help of a hammer.

Diagram Description: A wall is depicted. Drill positions are marked. Holes are drilled, and wall anchors (Q) are inserted using a hammer. This is the preparation for securing the cabinet to the wall.

Step 40: Secure Cabinet to Wall

Fix the cabinet to the wall with the provided screws (Q).

Diagram Description: The cabinet is shown positioned against the wall. Long screws (Q) are inserted through a strip on the cabinet and into the wall anchors to secure the unit. Quantities: Q x2.