FS Bullet Network Cameras

Introduction

Thank you for choosing the Bullet Network Cameras. This guide is designed to familiarize you with the structure of the cameras and describes how to deploy them in your network.

Camera Models:

• IPC101-2M-B/IPC101-5M-B
• IPC104-2M-B/IPC104-5M-B

Diagram Description: Images show two models of bullet network cameras, each with a mounting bracket.

Accessories

For IPC101-2M-B/IPC101-5M-B/IPC104-2M-B/IPC104-5M-B:

• Waterproof Kit x1: A kit containing components for weatherproofing the camera connections.
• Screw Kit x1: A set of screws and possibly wall anchors for mounting.
• Drill Template Sticker x1: A sticker with markings to guide drilling holes for mounting.

Hardware Overview

IPC101-2M-B/IPC101-5M-B

Diagram Description: Shows the rear of the camera with two connection cables labeled '1' and '2'.

IPC104-2M-B/IPC104-5M-B

Diagram Description: Shows the rear of the camera with a close-up view of the ports. Components are labeled: 1. Power Interface, 2. Network Interface, 3. Micro SD Card Slot, 4. Reset Button.

Installation Requirements

Precautions

• Make sure the working temperature is maintained at -30°C~60°C, and the relative humidity is ≤95%.
• Keep the camera with good ventilation from excessive pressure, vibration, dust, corrosive gases and intensive electromagnetic radiation.
• Keep the device placed on a flat surface. Unless otherwise specified, do not stack devices.
• Ensure that the cable is not tense. Lengthen the cable between the power adapter and mains if necessary.
• Do not overbend the cables or hold the tail cable by hand for weight bearing.
• The connectors of the tail cable, waterproof box, corrugated pipe and PVC pipe must be fully protected.
• Do not remove the protective film on the cover during mounting. Remove it before the device is powered on.
• Contact professionals for maintenance. Do not dismantle the device by yourself. FS shall not assume any responsibility for problems caused by unauthorized repair or maintenance.
• Using the device may involve the collection of personal information such as the face, fingerprint, license plate number, email, phone number, or GPS.

Maintenance

• Remove the dust on the front glass surface gently using an oil-free brush or a rubber dust blowing ball.
• Clean the glass surface gently from the center outward using a lens cleaning cloth. If necessary, use the cloth dipped with detergent.

⚠️ CAUTION: Never look at the laser, fiber ports and cable ends while the power is on.

Installation

Installing Micro SD Card (Optional)

Diagram Description: Shows the camera's bottom cover being opened with a screwdriver, and then the Micro SD card being inserted into the slot.

1. Open the bottom cover by loosening the screws.
2. Insert the Micro SD card (purchased separately) into the camera.

⚠️ NOTE: The Micro SD card doesn't support hot plug operation.

Installing the Waterproof Kit (Optional)

Diagram Description: Shows the assembly of waterproof components onto a network cable, with arrows indicating the sequence of connection.

Install the supplied waterproof components to the network cable in sequence.

Wall Mounting

Diagram Description: Shows a drill template sticker being applied to a wall, with alignment marks and a hole for cables.

1. Paste the drill template sticker on the wall and align the cross center to the hole. Lead the cables across the hole.

⚠️ NOTE: The ceiling mounting is similar to the wall mounting. This document takes the latter as an example.

Diagram Description: Illustrates drilling guide holes, inserting wall plugs, attaching the camera bracket, and connecting cables.

2. Drill 30mm-depth guide holes on the wall with a Ø6-6.5mm drill bit.
3. Knock the wall plugs of supplied self-tapping screws into the guide holes and tighten the plugs.
4. Unscrew the locknut to loosen the universal joint.
5. Connect the cables. Lead the screws through the guide holes in the base and fix the screws on the wall.
6. Adjust the opening of the universal joints. Rotate the spherical hinge of the camera to get the desired monitoring direction. Tighten the locknut.

Connecting the Power

PoE Device

Diagram Description: Shows a bullet network camera connected via an Ethernet cable to a PoE switch or NVR. It indicates the camera's Ethernet interface connecting to the PoE port.

Use an Ethernet cable to connect the Ethernet interface of the camera to the PoE port on a PoE device, such as a PoE switch or a PoE NVR.

Power Adapter

Diagram Description: Shows a bullet network camera connected via its power interface to a power adapter, which is then plugged into a wall outlet.

Connect the power interface of the camera to the local power supply with the power adapter (purchased separately).

Log in Camera

Before you begin, check that:

• Your camera is operating properly and connected to the network.
• The PC you are using is installed with Chrome 45 or later.

Follow these steps to log in your camera through the Web:

1. Open your browser, input the IP address of your camera in the address bar and then press Enter to open the login page. The default IP is 192.168.1.13.
2. Enter the default username and password (admin/admin) and then click Login.

Diagram Description: Screenshot of the camera's web login interface, featuring fields for Username and Password, with Login and Reset buttons.

⚠️ NOTE: 1. DHCP is enabled by default. If a DHCP server is used in your network, your camera may be assigned an IP address, and you need to use the assigned IP address to log in. 2. You may need to install a plug-in at your first login. Please follow the on-screen instructions to complete the installation and then open the browser again to log in. 3. The default password is intended only for your first login. To ensure security, please change the password after your first login. You are strongly recommended to set a strong password of at least nine characters including all three elements: digits, letters and special characters. 4. If the password has been changed, please use the new password to log in.

Online Resources

• Download: https://www.fs.com/products_support.html
• Help Center: https://www.fs.com/service/fs_support.html
• Contact Us: https://www.fs.com/contact_us.html

Product Warranty

FS ensures its customers that for any damage or faulty items due to workmanship, FS will offer a free return within 30 days from the day you receive your goods. This excludes any custom-made items or tailored solutions.

Warranty: The products enjoy a 2-year limited warranty against defects in materials or workmanship. For more details about the warranty, please check at https://www.fs.com/policies/warranty.html

Return: If you want to return the item(s), information on how to return can be found at https://www.fs.com/policies/day_return_policy.html

Compliance Information

FCC

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

UKCA

Hereby, FS.COM Innovation Ltd declares that this device is in compliance with the Directive SI 2016 No. 1091 and SI 2016 No. 1101.

FS.COM LIMITED

24F, Infore Center, No.19, Haitian 2nd Rd, Binhal Community, Yuehai Street Nanshan District, Shenzhen City

FS.COM Innovation Ltd

4th Floor Imperial House, 8 Kean Street, London, England, WC 2B 4AS

CE

FS.COM GmbH hereby declares that this device is in compliance with the Directive 2014/30/EU and 2014/35/EU. A copy of the EU Declaration of Conformity is available at https://www.fs.com/company/quality_control.html

FS.COM GmbH déclare par la présente que cet appareil est conforme à la Directive 2014/30/UE et 2014/35/UE. Une copie de la déclaration de conformité de l'UE est disponible à l'adresse suivante https://www.fs.com/fr/company/quality_control.html

FS.COM LIMITED
24F, Infore Center, No.19, Haitian 2nd Rd, Binhai Community, Yuehai Street, Nanshan District, Shenzhen City

FS.COM GmbH
NOVA Gewerbepark Building 7, Am Gfild 7, 85375 Neufahrn bei Munich, Germany

IC

CAN ICES-003(A)/NMB-003(A)

English: This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. The digital apparatus complies with Canadian CAN ICES-3 (A)/NMB-3(A).

French: Cet appareil contient des émetteurs/récepteurs exempts de licence qui sont conformes aux RSS exemptés de licence d'Innovation, Sciences et Développement économique Canada. L'exploitation est soumise aux deux conditions suivantes : (1) Cet appareil ne doit pas provoquer d'interférences. (2) Cet appareil doit accepter toute interférence, y compris les interférences susceptibles de provoquer un fonctionnement indésirable de l'appareil. l'appareil numérique du ciem conforme canadien peut - 3 (a) / nmb - 3 (a).