PROMISE Technology - Storage Solutions for IT, Cloud, Surveillance and Rich Media
User Guide for PROMISE TECHNOLOGY models including: PegasusPro R16, System CPU, PegasusPro R16 System CPU
6 мар. 2021 г. — The PegasusPro Series systems are shipped ready to use, configured with shared storage volumes on a RAID array. The user must download and install PROMISE ...
File Info : application/pdf, 2 Pages, 4.81MB
DocumentDocumentPegasusPro R16 Quick Start Guide OVERVIEW The PegasusPro Series systems are shipped ready to use, configured with shared storage volumes on a RAID array. The user must download and install PROMISE Utility Pro software on the computers used to mount and the Shared storage volume over the local network; or access the storage directly using a ThunderboltTM 3 cable. The initial setup procedure is summarized below: Preparing to install A. Unpacking the device B. Install Drivers and Software Device Installation 1. Connecting the power and powering on 2. Power on system 3. Connecting ThunderboltTM 3 cable 4. Connecting 10G cable(s) PROMISE Utility Pro Launch PROMISE Utility Pro, use for host administrator setup and connection to collaborative users. PREPARING TO INSTALL PEGASUSPRO R16 A UNPACKING The PegasusPro R16 box contains the following items: · One PegasusPro R16 enclosure · This Quick Start Guide · Two 1.5m (4.9 ft) Power cords · Thunderbolt 3 / USB3.2 cable B INSTALL SOFTWARE AND DRIVER First download and install the hardware driver for the host computer, or any other computer used to connect directly to the PegasusPro R16 via ThunderboltTM 3. Go to: promise.com > Products > Pegasus > PegasusPro > Download > Drivers Then download and install PROMISE Utility Pro on the host computer and collaborative user computers. Go to: promise.com > Products > Pegasus > PegasusPro > Download > Utilities The host computer is connected to the PegasusPro R16 via the ThunderboltTM 3 cable. This is a Direct Attached Storage (DAS) connection. Use the host computer for administration of the PegasusPro R16 and the storage network, including which users are allowed to access it. Promise Technology PegasusPro R16 Quick Start Guide DEVICE INSTALLATION 1 CONNECT POWER PegasusPro R16 enclosures are equipped a single power supply. Insert the female end of one of the supplied power cable in to a power cable receptacle on the power supply unit, and plug the other end in to a suitable power outlet. Power receptacle on rear panel 1 2 POWER ON Press the Power button on the front left bracket facing. Make sure to download and install the hardware driver for your computer before proceeding to connect the ThunderboltTM 3 port. The device illustrations here are for the purpose of describing the initial installation and setup. For more complete descriptions of the hardware, please see the Product Manual. 3 CONNECT PRIVATE PORT Connect the host computer directly to the PegasusPro R16 with a ThunderboltTM 3 cable. This Direct Attached Storage (DAS) connection is called the Private Port; it is used by one individual with access to two DAS volumes. After connecting the ThunderboltTM 3 cable, two DAS volumes appear on the desktop: PegasusPro_DAS1 and PegasusPro_DAS2. Later the host system can use PROMISE FileBoost to copy content from the DAS volumes to Shared folders. ThunderboltTM 3 and 10G ports on rear panel 3 4 Private Port and Share Port Connections PegasusPro is compatible with a ThunderboltTM4 Windows PC except when it is connected behind a Thunderbolt 4 dock or Hub (Goshen Ridge based). PROMISE SANLink3 Ethernet-to-ThunderboltTM 3 bridge is recommended for Mac collaborative users that do not have an Ethernet port. 4 CONNECT SHARE PORT Use a suitable Ethernet cabling (Cat. 6e or better) to connect one to four of the Share Ports (10G network ports) on the rear panel. The network cables for the Share Ports can be connected to a switched Ethernet network, or connect directly to a collaborative user computer. Mac users that do not have an Ethernet port, use the SANLink3 Ethernet-to-ThunderboltTM 3 bridge to connect to the 10G Share network. For simplicity, it is recommended to use DHCP on for all computers connected to the 10G network Share Ports. The 10G network Share Port enables the administrator to use PROMISE Utility Pro to manage the PegasusPro device, give access permission and create new shared or private folders. Other users connecting to the Share Port use PROMISE Utility Pro to mount shared folder for collaborative work. Power button on front left side 2 SanLink3 ThunderboltTM 3 port on collaborative user computer 4 3 Make sure the computer port is a ThunderboltTM 3 female connection. A ThunderboltTM 3 port has a ThunderboltTM icon next to the port. 1 ThunderboltTM 3 port on administrator's computer Version 1.0 PN: G6102PR16000000 PROMISE UTILITY PRO Host Computer Use the host computer to launch PROMISE Utility Pro. Log in as the PegasusPro system administrator using the default account log in: User Account: admin Password: admin Host Folders When connected to the PegasusPro, the host will see two DAS volumes under On DAS Space, a shared Public Folder and a shared Home Folder. New folders are created by clicking on the New Folder button. Host Access Request Collaborative user accounts will ask for permission to access the PegasusPro. The host account can Approve or Dismiss the request. Collaborative Users Launch PROMISE Utility Pro, the PegasusPro system will be located automatically. Click on Continue with Mac Device to automatically set up your user account. Collaborative User folder An access request is sent to the host computer - once access is granted, collaborative users see the default shared folders -- Public Folder, Home Folder. Promise Technology PegasusPro R16 Quick Start Guide 2