SENSO Coffee Table

Product Dimensions

Width: 68.1 cm

Depth: 68.1 cm

Height: 48.4 cm

Parts List

Panels:

• F-1: 681x681x16mm (x1)
• F-2: 681x681x16mm (x1)
• F-3: 252x678x16mm (x1)
• F-4: 252x678x16mm (x1)
• F-5: 252x648x16mm (x1)
• F-6: 648x66x18mm (x1)
• F-7: 642x204x16mm (x1)
• F-8: 300x120x16mm (x1)
• F-9: 300x120x16mm (x1)
• F-10: 592x120x16mm (x1)
• F-11: 622x306x3mm (x1)

Hardware:

• A: 7x50mm screws (x10)
• B: 8x32mm screws (x20)
• E: 3.5x13mm screws (x6)
• EP1: 4x16mm screws (x26)
• K6: Cam lock mechanism part (x1)
• M02: Magnetic catch (x1)
• N2: Feet/Supports (20x20/H=200mm) (x4)
• R: 5x9mm screws (x8)
• T3: Cam lock pins (x10)
• U: L=24.3mm parts (x8)
• W6: 3.5x13mm screws (x6)
• XA: 7x50mm screws (x2)
• ZA: Ø4mm parts (x10)
• ZR: Ø15mm parts (x8)

Note: Some panels may have load limits indicated (e.g., 2kg, 5kg).

Safety and Care Instructions

Safety Warnings

• [!] Check all parts for damage before assembly. If damaged, do not proceed and file a complaint.
• [!] Do not exceed maximum load values specified for the furniture.
• [!] When mounting to a wall, check the wall type and strength. Use appropriate wall fixings. Consult a specialist if unsure.
• [!] Assembly must be performed by a competent person.
• [!] Furniture with wood-based panels may emit pollutants. Ventilate the room frequently for at least four weeks after assembly.
• [!] Do not place hot objects on the furniture.
• [!] Do not place candles directly on the furniture.
• [!] Wipe up spilled liquids immediately.
• [!] Regularly check that screws and fittings are tight.
• [Note] The typical aromatic wood smell is a sign of quality for natural wood furniture.
• [Note] Bright spots on knots from natural resin can be polished with a dry, lint-free cloth.
• [Note] Initial odors from new materials are normal and will disappear over time. Ventilate frequently or wipe with water diluted with a little vinegar to speed up the process.

Cleaning Recommendations

• For panel materials, use a soft, lint-free cloth or a chamois leather. Wipe surfaces slightly damp.
• [X Mark] Avoid using: Microfibre cloths, dirt erasers, harsh chemicals, abrasive cleaning agents or solvents, scouring powder, steel wool, scouring pads, vacuum cleaner nozzles/brushes, or steam cleaners. These can scratch, damage, or destroy the surface.

Assembly Steps

Step 1: Base and Side Panels

Attach panels F-3, F-4, and F-5 to the base panel F-1. Use screws B (8x32mm) and U (L=24.3mm). Secure panels using cam pins T3 and cam locks K6. Panel F-2 is the top panel.

Step 2: Attach Side Panels

Attach side panels F-3 and F-4 to the base panel F-1 using screws R (5x9mm).

Step 3: Attach Back and Side Panels

Attach the back panel F-6 and the side panel F-4 to the existing structure using screws R (5x9mm).

Step 4: Attach Front Panel

Attach the front panel E to the assembly using screws E (3.5x13mm).

Step 5: Attach Top Panel

Place the top panel F-2 onto the assembled sides and secure it using screws A (7x50mm).

Step 6: Attach Feet and Brackets

Attach the feet N2 to the underside of the base panel F-1. Attach corner brackets EP1 to the top corners of the side panels using screws A (7x50mm) and EP1 (4x16mm).

Step 7: Assemble Drawer Housing

Assemble the drawer housing by attaching panels F-7, F-8, and F-9 to the main unit. Use screws B (8x32mm) and U (L=24.3mm).

Step 8: Attach Drawer Front/Back

Attach panel F-10 to panels F-8 and F-9 using screws A (7x50mm) and XA (7x50mm).

Step 9: Complete Drawer Box

Attach panel F-7 to panels F-9 and F-10 using screws R (5x9mm) to form the drawer box.

Step 10: Insert Drawer Panel

Slide the drawer panel F-11 into the assembled drawer box.

Step 11: Secure Drawer Panel

Secure the drawer panel F-11 using screws EP1 (4x16mm).

Step 12: Attach Drawer Slides

Attach the drawer slides K6 to the sides of the drawer box and the main unit. Use screws T3 (cam lock pins) and the corresponding cam lock mechanism parts.

Step 13: Insert Drawer

Insert the assembled drawer into the main unit. Use parts ZA and ZR, likely for a push-to-open mechanism.

Step 14: Adjust Drawer Slides

Adjust the drawer slides as shown in the diagram to ensure smooth operation and proper alignment.

Step 15: Final Drawer Assembly

Complete the drawer assembly. Attach any remaining hardware like the magnetic catch M02 and use screws E (3.5x13mm) and K6b (part of cam lock system).