AIMOTION Casambi DALI Controller 10 / CBU-A2D
Controller for 10 luminaires with DALI or 2 luminaires with 0-10V control unit
Article no.: 1003P
Description
The AIMOTION controller controls individual luminaires in the Bluetooth Low Energy Mesh network without the use of gateways, routers, repeaters or extra cabling. The controller is connected directly to 100-240 Volt AC. The DALI-BUS output can be loaded with up to 20 mA max. The configuration and selection of the appropriate profile for the different operating modes (8xDIM, TW, RGB, RGBW, etc.) is done wirelessly via the Casambi App.
The installation may only be carried out by a qualified electrician.
Features
- Selectable operating mode / profiles
- Separate control of max. 8 DALI luminaires
- Wireless control via app, wall switch and motion detector
- Automatic switching on and off according to time, weekday, date or sunshine
- Group function
- Integration in scenes and animations
- iBeacon can be activated
Technical Details
| Description | Features |
|---|---|
| Operating voltage | 100-240 VAC / 50 Hz |
| Radio frequencies | 2,4...2,483 GHz / +4 dBm |
| Mains current | <0,5 W |
| Output channel 1 | 0-10 VDC, max. 7 mA DALI: 12 VDC, max. 20 mA |
| Output channel 2 | 0-10 VDC, max. 7 mA Relais: 12 VDC, max. 100 mA |
| Wire range, solid & stranded | 0,5-1,5 mm² |
| Wire strip length | 6-7 mm |
| Ambient temperature, ta | -20...+45 °C |
| Storage temperature | -25...+70 °C |
| Degree of protection | IP20 |
| Protection class | - |
| Weight | 40 g |
| Dimensions | 76 x 26 x 23 mm |
Wiring diagram for DALI or 0-10V driver:
Diagram shows connections for N (Neutral), L (Live), and the output terminals for DALI or 0-10V drivers. It indicates optional 12V relay connection.
Wiring diagram for two 0-10V drivers:
Diagram shows connections for N (Neutral), L (Live), and two separate 0-10V output channels (ch1, ch2) for drivers.
Commissioning
Follow these steps to add the device to a network:
- Open the Casambi App and log in to your Bluetooth network. If you have not yet created a network, you must create a new network.
- Before adding the device to the network, select the appropriate profile. Tap on 'More', then tap on 'Devices nearby'. Then tap the device, tap 'Change Profile' and follow the instructions.
- In the Near Devices overview, tap the device and add it to the network.
- The device is added to the network and ready to use.
- Optional: Use Casambi-enabled switches. Tap on 'More', then tap on 'Switches'. Then tap the switch you want to use.
Profiles
- DALI Controller Broadcast
- DALI 2CH
- DALI 3CH
- DALI 4CH
- DALI 5CH [Evo]
- DALI 6CH [Evo]
- DALI 7CH [Evo]
- DALI 8CH [Evo]
- DALI TW
- DALI RGB
- DALI RGB White
- DALI DT8 RGB/TW
- DALI DT8 TW
- DALI DT8 TW (Log)
- DALI DT8 XY/TW [Evo]
- 0-10V 2CH
- 0-10V + Relay
- 0-10V 2CH, Vertical
- 0-10V TW
- 0-10V 2CH, TW [NoMix]
Declaration of Conformity
CASAMBI Technologies Oy declares that the product DALI Controller 10 / CBU-A2D is in compliance with Directive 2014/53/EU. The detailed declaration of conformity can be found at https://www.aimotion-smartliving.de/en/support-en/download/ in the product category Dimmer.